mirror of
https://github.com/smaeul/u-boot.git
synced 2025-10-13 20:36:02 +01:00
mips: octeon: mrvl, octeon-nic23.dts: Add ethernet DT support
Add the Octeon ethernet (BGX) and SFP DT nodes to the NIC23 dts file to enable ethernet support on this board. Signed-off-by: Stefan Roese <sr@denx.de>
This commit is contained in:
parent
03b5f836b6
commit
f858bcccf4
@ -118,11 +118,208 @@
|
||||
&i2c0 {
|
||||
u-boot,dm-pre-reloc; /* Needed early for DDR SPD EEPROM */
|
||||
clock-frequency = <100000>;
|
||||
|
||||
sfp0eeprom: eeprom@50 {
|
||||
compatible = "atmel,24c01";
|
||||
reg = <0x50>;
|
||||
};
|
||||
|
||||
sfp0alerts: eeprom@51 {
|
||||
compatible = "atmel,24c01";
|
||||
reg = <0x51>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
u-boot,dm-pre-reloc; /* Needed early for DDR SPD EEPROM */
|
||||
clock-frequency = <100000>;
|
||||
|
||||
vitesse@10 {
|
||||
compatible = "vitesse,vsc7224";
|
||||
reg = <0x10>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* Note that reset is active high with this device */
|
||||
reset = <&gpio 7 0>;
|
||||
|
||||
/* LoS pin can be pulled low when there is a loss of signal */
|
||||
los = <&gpio 6 0>;
|
||||
|
||||
vitesse,reg-init =
|
||||
/* Clear all masks */
|
||||
/* Page select FSYNC0 (0x30) */
|
||||
<0x7f 0x0030>,
|
||||
/* Set FSYNC0 for 10.3125Gbps */
|
||||
<0x80 0x2841>, /* See Table 3. */
|
||||
<0x81 0x0008>,
|
||||
<0x82 0xc000>,
|
||||
<0x83 0x0010>,
|
||||
<0x84 0x1d00>,
|
||||
|
||||
/* All channels Rx settings set equally */
|
||||
<0x7f 0x0050>,
|
||||
/* Shrink EQ_BUFF */
|
||||
<0x82 0x0014>,
|
||||
/* Set EQVGA_ADAP = 1 (enable EQVGA circuitry),
|
||||
* USE_UNIT_GAIN = 1 (EQVGA is in unity gain),
|
||||
* USE_LPF = 0 (VGA adapt not using LPF),
|
||||
* USE_EQVGA = 1
|
||||
<0x89 0x7f13>,
|
||||
/* Select min DFE Delay (DFE_DELAY) */
|
||||
<0x90 0x5785>,
|
||||
/* Set DFE 1-3 limit (DXMAX) = 32dec,
|
||||
* AP Max limit = 127 decimal
|
||||
*/
|
||||
<0x92 0x207f>,
|
||||
/* Set AP Min limit = 32 decimal */
|
||||
<0x93 0x2000>,
|
||||
/* Set DFE Averaging to the slowest (DFE_AVG) */
|
||||
<0x94 0x0031>,
|
||||
/* Set Inductor Bypass OD_IND_BYP = 0 & fastest Rise/Fall */
|
||||
<0x9c 0x0000>,
|
||||
/* Setting DFE Boost = none. Must set for
|
||||
* rev C (if DFE in adapt mode)
|
||||
*/
|
||||
<0xaa 0x0888>,
|
||||
/* Setting EQ Min = 8 & Max limit = 72 dec.
|
||||
* Must set for rev C, otherwise EQ is 0
|
||||
* (if EQ is in adaptive mode)
|
||||
*/
|
||||
<0xa8 0x2408>,
|
||||
/* Setting EQVGA = 96, when in EQVGA manual mode */
|
||||
<0xa9 0x0060>,
|
||||
/* Setting SW_BFOCM, bits 15:14 to 01 */
|
||||
<0x87 0x4021>,
|
||||
/* Turn off adaptive input equalization
|
||||
* and VGA adaptive algorithm control.
|
||||
*/
|
||||
<0x89 0x7313>,
|
||||
/* Turn on adaptive input equalization
|
||||
* and VGA adaptive algorithm control.
|
||||
*/
|
||||
<0x89 0x7f13>;
|
||||
|
||||
vitesse-channel@0 {
|
||||
compatible = "vitesse,vsc7224-channel";
|
||||
reg = <0>;
|
||||
direction-tx;
|
||||
sfp-mac = <ð0>;
|
||||
|
||||
/* TAP settings. The format of this is as
|
||||
* follows:
|
||||
* - cable length in meters, 0 = active or
|
||||
* optical module
|
||||
* - maintap value
|
||||
* - pretap value
|
||||
* - posttap value
|
||||
*
|
||||
* For the cable length, the value will apply
|
||||
* for that cable length and greater until the
|
||||
* next largest cable length specified. These
|
||||
* values must be ordered first by channel mask
|
||||
* then by cable length. These are typically
|
||||
* set for the transmit channels, not the
|
||||
* receive channels.
|
||||
*/
|
||||
taps = <0 0x0013 0x000f 0x0000>,
|
||||
<1 0x001f 0x000f 0x0004>,
|
||||
<3 0x0014 0x000b 0x0004>,
|
||||
<5 0x0014 0x0009 0x0006>,
|
||||
<7 0x0014 0x000f 0x0000>,
|
||||
<10 0x0012 0x000b 0x0013>;
|
||||
};
|
||||
|
||||
vitesse-channel@1 {
|
||||
compatible = "vitesse,vsc7224-channel";
|
||||
reg = <1>;
|
||||
/* Ignore mod_abs and module */
|
||||
direction-rx;
|
||||
sfp-mac = <ð0>;
|
||||
|
||||
/* Disable pre-tap */
|
||||
pretap-disable;
|
||||
|
||||
/* Disable post-tap */
|
||||
posttap-disable;
|
||||
|
||||
/* Taps has the following fields:
|
||||
* - cable length (ignored for rx)
|
||||
* - main tap value
|
||||
* - pre tap value
|
||||
* - post tap value
|
||||
*
|
||||
* NOTE: if taps are disabled then they
|
||||
* are not programmed.
|
||||
*/
|
||||
taps = <0 0x0a 0x0b 0x10>;
|
||||
};
|
||||
|
||||
vitesse-channel@2 {
|
||||
compatible = "vitesse,vsc7224-channel";
|
||||
reg = <2>;
|
||||
direction-tx;
|
||||
sfp-mac = <ð1>;
|
||||
|
||||
/* TAP settings. The format of this is as
|
||||
* follows:
|
||||
* - cable length in meters, 0 = active or
|
||||
* optical module
|
||||
* - maintap value
|
||||
* - pretap value
|
||||
* - posttap value
|
||||
*
|
||||
* For the cable length, the value will apply
|
||||
* for that cable length and greater until the
|
||||
* next largest cable length specified. These
|
||||
* values must be ordered first by channel mask
|
||||
* then by cable length. These are typically
|
||||
* set for the transmit channels, not the
|
||||
* receive channels.
|
||||
*/
|
||||
taps = <0 0x0013 0x000f 0x0000>,
|
||||
<1 0x001f 0x000f 0x0004>,
|
||||
<3 0x0014 0x000b 0x0004>,
|
||||
<5 0x0014 0x0009 0x0006>,
|
||||
<7 0x0014 0x000f 0x0000>,
|
||||
<10 0x0012 0x000b 0x0013>;
|
||||
};
|
||||
|
||||
vitesse-channel@3 {
|
||||
compatible = "vitesse,vsc7224-channel";
|
||||
reg = <3>;
|
||||
/* Ignore mod_abs and module */
|
||||
direction-rx;
|
||||
sfp-mac = <ð1>;
|
||||
|
||||
/* Disable pre-tap */
|
||||
pretap-disable;
|
||||
|
||||
/* Disable post-tap */
|
||||
posttap-disable;
|
||||
|
||||
/* Taps has the following fields:
|
||||
* - cable length (ignored for rx)
|
||||
* - main tap value
|
||||
* - pre tap value
|
||||
* - post tap value
|
||||
*
|
||||
* NOTE: if taps are disabled then they
|
||||
* are not programmed.
|
||||
*/
|
||||
taps = <0 0x0a 0x0b 0x10>;
|
||||
};
|
||||
};
|
||||
|
||||
sfp1eeprom: eeprom@50 {
|
||||
compatible = "atmel,24c01";
|
||||
reg = <0x50>;
|
||||
};
|
||||
|
||||
sfp1alerts: eeprom@51 {
|
||||
compatible = "atmel,24c01";
|
||||
reg = <0x51>;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc {
|
||||
@ -151,6 +348,26 @@
|
||||
compatible = "marvell,pci-bootcmd";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
sfp0: sfp-slot@0 {
|
||||
compatible = "ethernet,sfp-slot";
|
||||
tx_disable = <&gpio 16 0>;
|
||||
mod_abs = <&gpio 17 0>;
|
||||
tx_error = <&gpio 19 0>;
|
||||
rx_los = <&gpio 18 0>;
|
||||
eeprom = <&sfp0eeprom>;
|
||||
diag = <&sfp0alerts>;
|
||||
};
|
||||
|
||||
sfp1: sfp-slot@1 {
|
||||
compatible = "ethernet,sfp-slot";
|
||||
tx_disable = <&gpio 21 0>;
|
||||
mod_abs = <&gpio 22 0>;
|
||||
tx_error = <&gpio 24 0>;
|
||||
rx_los = <&gpio 23 0>;
|
||||
eeprom = <&sfp1eeprom>;
|
||||
diag = <&sfp1alerts>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
@ -160,3 +377,24 @@
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
/* BGX 2 */
|
||||
&bgx2 {
|
||||
status = "okay";
|
||||
|
||||
/* SerDes 0, may differ from PCS Lane/LMAC */
|
||||
eth0: ethernet-mac@0 {
|
||||
compatible = "cavium,octeon-7890-bgx-port";
|
||||
reg = <0>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
sfp-slot = <&sfp0>;
|
||||
};
|
||||
|
||||
/* SerDes 1, may differ from PCS Lane/LMAC */
|
||||
eth1: ethernet-mac@1 {
|
||||
compatible = "cavium,octeon-7890-bgx-port";
|
||||
reg = <1>;
|
||||
local-mac-address = [ 00 00 00 00 00 00 ];
|
||||
sfp-slot = <&sfp1>;
|
||||
};
|
||||
};
|
||||
|
Loading…
x
Reference in New Issue
Block a user