Now that the PMIC has a DM driver and binds device tree subnodes, the
GPIO device can be bound that way, instead of from inside board code.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it does not differentiate among
the supported compatibles.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This is now handled automatically by the clock and pinctrl drivers.
SPL still calls this function because it needes the non-DM code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that issues with the BROM have been sorted out, we can implement
PSCI system suspend on H3 by delegating to SCP firmware. Let's start by
including the firmware in the FIT image and starting the coprocessor if
valid firmware is loaded.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that mkimage can generate TOC0 images, and the SPL can interpret
them, hook up the build infrastructure so the user can choose which
image type to build. Since the absolute load address is stored in the
TOC0 header, that information must be passed to mkimage.
Cover-letter:
sunxi: TOC0 image type support
This series adds support for the TOC0 image format used by the Allwinner
secure boot ROM (SBROM). This series has been tested on the following
SoCs/boards, with the eFuse burnt to enable secure mode:
- A50: Ainol Q88 Tablet
- A64: Pine A64 Plus
- H5: Orange Pi Zero Plus
- H6: Pine H64 Model B
- H616: Orange Pi Zero 2
This time I also tested it on boards that are not switched to secure
mode (with A64, H3, and H5).
Due to both series changing Makefile.spl, the last patch depends on:
https://patchwork.ozlabs.org/project/uboot/list/?series=267136
Since this series no longer selects TOOLS_LIBCRYPTO anywhere, building
certain platforms/options may fail with an error like the following if
TOOLS_LIBCRYPTO is disabled:
MKIMAGE spl/sunxi-spl.bin
./tools/mkimage: unsupported type Allwinner TOC0 Boot Image
make[1]: *** [scripts/Makefile.spl:426: spl/sunxi-spl.bin] Error 1
make: *** [Makefile:1982: spl/u-boot-spl] Error 2
END
Series-to: sunxi
Series-version: 4
Series-changes: 2
- Rebase on top of Icenowy's RISC-V support series
- Rename Kconfig symbols to include the full image type name
Signed-off-by: Samuel Holland <samuel@sholland.org>
Without default setting of gd->env_addr, U-Boot will cause
a synchronous abort if the env-variables on the SPI flash is
broken or not saved corectly. Set gd->env_addr correctly.
This reverts commit 535870f3b0fb09ee9b2885409f05304111464643.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
The subdivision name "TQ Components" hasn't been in use for a long time.
Rename the vendor directory to "tq", which also matches our Device Tree
vendor prefix.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Config check should be done without the SPL_ prefix.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Link: https://lore.kernel.org/r/20211104192802.3093811-1-ricardo@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to filter out NET_ETH_START errors because we have to enable
networking in order to propagate the MAC addresses to the DT while there
is no network driver for the prueth in U-Boot yet.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DHSOM uses different SPI NOR layout than the ST devkit, stop
pulling in the ST specific runtime mtdparts settings and adjust
the mtdparts accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
I'd like to keep informed about ls1028a.dtsi changes. For now, there is
no top-level entry for any layerscape specific files. Instead, add the
file entry to my board MAINTAINERS file.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Increase fdt blob size for lx2160 and lx2162 series
to fix below errors/warnings during device tree fixup.
Unable to update property /soc/spi@2100000:status, err=FDT_ERR_NOSPACE
Unable to update property /soc/spi@2110000:status, err=FDT_ERR_NOSPACE
Unable to update property /soc/spi@2120000:status, err=FDT_ERR_NOSPACE
WARNING: could not set reg FDT_ERR_NOSPACE.
WARNING unable to set iommus: FDT_ERR_NOSPACE
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set popts->cpo_sample to 0x54 in t104xrdb/ddr.c to optimize cpo
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to ./include/linux/kconfig.h,
CONFIG_IS_ENABLED(OF_BOARD) expands to 0
when CONFIG_SPL_BUILD is defined because
there is no CONFIG_SPL_OF_BOARD.
Use #if defined instead.
Fixes: 2e8d2f88439d ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Most modern platforms use 64-bit EFI so it is useful to have a U-Boot app
that runs under that. Add a (non-functional) build for this.
Note that --whole-archive causes the gcc 9.2 linker to crash, so disable
this for now. Once this is resolved, things should work.
For now, avoid mentioning the documentation for the 64-bit app, since it
does not work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- add JetHub D1 eth mac generation with manufacturer OUI
-----BEGIN PGP SIGNATURE-----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=UyL3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211102' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- add sm efuse write support and cmd for read/write efuse
- add JetHub D1 eth mac generation with manufacturer OUI
patman 'postfix' support
fix binman test race condition causing a timeout error
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmF+8FcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYP+AgApwZWYteNQu/OKwCFrZq0QIQYZwJQqe93
9CdQtpKH2boakfNcvsbPP5dXk8GNz5cEky1Whk2kIH1b11FHgklnIPFtFxzMesm8
oYET1w0iItp+4P4ZsQmVgJpynz4yUmUnMEOBNqwI2zeo7dMgx8Zw+cWz8FDo4e6K
pDKHAx9UmiCRu6h+IbsAzeMcq/HqAvFOzoWbp/LkmaWnwIjASCM4UUVoz1+UtoFU
0ENn/7vn70WOLw0JoEib8M7qy+IT7Mz42eZwDVGzYKSDlTZmXNwKLLzgJpEqW4hw
lYIEBUK3sr0q+kcKI776JeFaFhI6k71uVJcjkkUgGuF1hda1kc0Msw==
=E8s4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-boo21' of https://source.denx.de/u-boot/custodians/u-boot-dm
Environment tidy-ups
patman 'postfix' support
fix binman test race condition causing a timeout error
# gpg: Signature made Sun 31 Oct 2021 03:36:55 PM EDT
# gpg: using RSA key B25C0022AF86A7CC1655B6277F173A3E9008ADE6
# gpg: issuer "sjg@chromium.org"
# gpg: Good signature from "Simon Glass <sjg@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B25C 0022 AF86 A7CC 1655 B627 7F17 3A3E 9008 ADE6
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes we use uchar and sometimes char for the default environment
array. By always using char, we can get rid of some explicit casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Various freescale boards set gd->env_addr to default_environment in
board_init(), conditional on CONFIG_ENV_IS_NOWHERE, but this is
redundant, since it is done by env_init() before board_init() is called.
Let the env subsystem handle this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board sets gd->env_addr to default_environment in board_init(), but
the board has environment in SPI flash according to defconfig. Let the
env API handle environment automatically.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Samsung Galaxy A3, A5, A7 (2017) - middle class Samsung smartphones.
U-boot can be used as chain-loaded bootloader to gain control
on booting vanilla linux(and possibly others) kernels
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659f7fca9ea65df4318e5bca2b8274310.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that the three M/N/H variants can be built from one config,
rename the defconfig file to be more generic since it supports multiple
RZ/G2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TARGET_BEACON_RZG2M can handle all the work that
was done with TARGET_BEACON_RZG2N and TARGET_BEACON_RZG2H,
remove them since they just create more duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
There are three boards from Beacon, RZ/G2 M/N/H which all
use the same board file, but different device trees.
Add code to automatically select the proper device tree
based on the CPU type.
Signed-off-by: Adam Ford <aford173@gmail.com>
JetHome has own MAC OUI. Add jethub-j100 board file. Update config.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fix issue reported by checkpatch.pl
WARNING: Possible comma where semicolon could be used
#499: FILE: board/xilinx/zynqmp/zynqmp.c:499:
+ size = ALIGN(CONFIG_SYS_MALLOC_LEN + total_size, MMU_SECTION_SIZE),
+ reg = lmb_alloc(&lmb, size, MMU_SECTION_SIZE);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/ef264451ef9455ada9784bedbc91f74b94b8a237.1634799528.git.michal.simek@xilinx.com
- mvebu: Fix usage of BIN header arguments (Pali)
- mvebu: turris_omnia: Fix MTD partitions order for Linux (Pali)
- mvebu: nandpagesize support for kwbimage v1 (Pali)
