Remove device tree overlay (DTBO) entries for the ZynqMP target
from the Makefile. Add new device tree binaries (DTBs) for the
zynqmp-sm-k24-revA and zynqmp-smk-k24-revA configurations.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240906070808.1045991-3-prasad.kummari@amd.com
Linux commits:
15d16d6dadf6 kbuild: Add generic rule to apply fdtoverlay
44f87191d105 kbuild: parameterize the .o part of suffix-search
The Linux commit 15d16d6dadf6 adds a generic rule in Makefile.lib
to automatically apply fdtoverlay, so that each platform doesn't
need to include a complex rule. This also automatically appends
DTC_FLAGS_foo_base += -@ to all base files
The platform's Makefile only needs to have this now:
foo-dtbs := foo_base.dtb foo_overlay1.dtbo foo_overlay2.dtbo
dtb-y := foo.dtb
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240906070808.1045991-2-prasad.kummari@amd.com
Add support for the Comvetia i.MX6Q LXR2 board, which is
uses the Phytec PFLA02 SoM.
Based on the original work from Stefano Babic <sbabic@denx.de>.
The Phytec PFLA02 devicetrees are taken from kernel 6.11-rc7.
The imx6q-lxr.dts has been submitted upstream:
https://lore.kernel.org/linux-devicetree/20240913200906.1753458-3-festevam@gmail.com/
After it gets accepted in mainline (most likely in kernel 6.13),
the lxr2 board can then be switched to OF_UPSTREAM and these device trees
can be removed from U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable OF_UPSTREAM for Keystone boards. Remove DT files that
are now available in dts/upstream.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Neha Malcom Francis <n-francis@ti.com>
Instead of using the local imx6-tqma6 devicetree copies from U-Boot,
convert the imx6-tqma6 target to OF_UPSTREAM so that the upstream
kernel devicetrees can be used instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The Tanix TX1 is a tiny TV box, featuring the Allwinner H313 SoC with up
to 2GB of DRAM and 16GB of eMMC. There is no SD card or Ethernet port on
this small device, but it can be booted via the USB debug "FEL" mode.
The bootloader could then be written to the eMMC.
Add the defconfig for that board, and add the devicetree file to the
Makefile, for it to be built.
The DRAM parameters were taken from the vendor firmware on the eMMC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Instead of using the local imx7s-warp devicetree copies from U-Boot,
convert the imx7s-warp board to OF_UPSTREAM so that the upstream
kernel devicetree can be used instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of using the local imx6sx-udoo-neo devicetree copies from U-Boot,
convert the imx6sx-udoo-neo boards to OF_UPSTREAM so that the upstream
kernel devicetrees can be used instead.
Tested on a imx6sx-udoo-neo-full board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
No meaningful changes were made to this SoM since February 2021. Nobody
from Theobroma has booted anything recent on that product since July
2021 at the latest. The product isn't available to buy anymore and
disappeared from our website.
This product is therefore unmaintained and it would be disingenuous to
say the opposite, so drop support for RK3368 Lion.
If you're a user of Lion, feel free to revert this patch or contact our
sales/support department.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
DEFAULT_DEVICE_TREE in DS116 defconfig. Remove current DTS in
arch/arm/dts/ directory.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT and SoM rev.100 backward
compatibility DTO to cater for this change.
Since the MDIO address adjustment is now also in the rev.100 SoM DTO, not
only in the rev.100 PDK3 DTO, update Makefile accordingly as well, else the
DTC would complain about the DTO overriding the 'reg' property without also
updating the node unit-address, which is not doable without duplicating the
entire PHY node in the DTO, which leads to large amount of duplication with
no gain.
Fixes: 9de599ec3d59 ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
The Lenovo IdeaPad Yoga 11 is a hybrid laptop/tablet Windows RT-based
computer released in late 2012. The device uses a 1.3 GHz quad-core
Nvidia Tegra 3 chipset with 2 GB of RAM, features a 11.6 inch 1366x768
screen and 32/64 GB of internal memory that can be supplemented with
a microSDXC card slot, full size SD card slot and 2 full size USB 2.0
ports.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Surface RT is a hybrid tablet computer developed and manufactured
by Microsoft and shipped with Windows RT. The tablet uses a 1.3 GHz
quad-core Nvidia Tegra 3 chipset with 2 GB of RAM, features 10.8
inch 1366x768 screen and 32/64 GB of internal memory that can be
supplemented with a microSDXC card giving up to 200 GB of
additional storage.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
WEXLER Tab 7t is a mini tablet computer developed by WEXLER that
runs the Android operating system. The device features a 7.0-inch
(180 mm) HD display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM,
8, 16 or 32 GB of storage that can be supplemented with a microSDXC
card giving up to 64 GB of additional storage and a full size USB
port.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Asus Eee Pad Transformer family are 2-in-1 detachable/slider
tablets developed by Asus that run the Android operating system.
The Eee Pad Transformers feature a 10.1-inch (260 mm) display,
an Nvidia Tegra 2 dual-core chip, 1 GB of RAM, and 16/32 GB of storage.
Transformers board derives from Nvidia Ventana development board.
This patch brings support for all 3 known T20 Transformers:
- Asus Eee Pad Transformer TF101
- Asus Eee Pad Transformer TF101G
- Asus Eee Pad Slider SL101
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Migrate imx8mn_bsh_smm_s2 and imx8mn_bsh_smm_s2pro boards to OF_UPSTREAM.
Signed-off-by: Patrick Barsanti <patrick.barsanti@amarulasolutions.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Jayesh Choudhary <j-choudhary@ti.com> says:
Hello there,
This series add the U-Boot support for our new platform of K3-SOC
family - J722S-EVM which is a superset of AM62P. It shares the same
memory map and thus the nodes are being reused from AM62P includes
instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
- Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
- Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
- 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
TRM: <https://www.ti.com/lit/zip/sprujb3>
Schematics: <https://www.ti.com/lit/zip/sprr495>
Boot test log:
<https://gist.github.com/Jayesh2000/0313e58fde377f877a9a8f1acc2579ef>
Include the uboot device tree files needed to boot the board.
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
This stm32mp135f-dhcor-dhsbc board is a stack of DHCOR SoM based on
STM32MP135F SoC (900MHz / crypto capabilities) populated on DHSBC
carrier board.
The SoM contains the following peripherals:
- STPMIC (power delivery)
- 512MB DDR3L memory
- eMMC and SDIO WiFi module
The DHSBC carrier board contains the following peripherals:
- Two RGMII Ethernet ports
- USB-A Host port, USB-C peripheral port, USB-C power supply plug
- Expansion connector
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZnBfewAKCRDKSWXLKUoM
Ib/7AJ0cn3q7lMpxbSbRj33oftI8Vy8+owCeN35Nl8TN9l/DHbfusER4uVfnOVw=
=YMIB
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
Nishanth Menon <nm@ti.com> says:
Cleanup am625 on by switching over the last two platforms (SK and
beagleplay) over to OF_UPSTREAM, and while at it, switch over am62a7
(last of the am62* family) over as well.
This superscedes the previous version of beagleplay only patch[1]
Test logs: https://gist.github.com/nmenon/ba310d3750a80789aca6a4fd90190135
Enable OF_UPSTREAM for am62a7-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Enable OF_UPSTREAM for am625-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Enable OF_UPSTREAM for AM625-beagleplay board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Migrate PX30/RK3326 boards that exists in Linux v6.8 to use OF_UPSTREAM.
firefly-px30 is not migrated to OF_UPSTREAM because there's no Device
Tree in the Linux kernel.
Differences between U-Boot's Odroid-Go2 and Linux's are now moved to the
-u-boot.dtsi, though I have a gut feeling that the existing cru
overrides aren't necessary (anymore?).
The U-Boot GPIO led-0 is on GPIO0_C1 but such is the pin of PWM3 which
is used for Linux's PWM led-2 so keep Linux's.
I also doubt vcc_cam is actually used, though the Odroid-Go2 Black
Edition uses this dcdc regulator for WiFi, so let's just move it to the
-u-boot.dtsi to play it safe.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Move to using OF_UPSTREAM config and thus using the devicetree-rebasing
subtree.
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Neha Malcom Francis <n-francis@ti.com> says:
This series was plucked out from the larger series [1] that did some
templating reformatting and also enabled OF_UPSTREAM for J721E. The
former has been kept aside till all the platforms affected have moved to
using OF_UPSTREAM to have less conflicts while merging.
Patches split J721E EVM and J721E SK to using separate builds, as well
as enable OF_UPSTREAM for both the platforms.
Boot logs:
https://gist.github.com/nehamalcom/8f326376b6c6b1196084721405159bb9
[1] https://lore.kernel.org/all/20240322131011.1029620-1-n-francis@ti.com/
Move to using OF_UPSTREAM config and thus using the devicetree-rebasing
subtree.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20956
- Support different RAM sizes on imx8m phycoce boards.
- Support new toradex variants.
- Support Samsung 4GB DDR and Realtek RTL8211E PHY on imx8mm-cl-iot-gate.
- Convert imx8mm-phycore and imx8mp-phycore boards to use OF_UPSTREAM.
The PHYCORE_IMX8MP is used by the phyBOARD-Pollux. Migrate board to
OF_UPSTREAM. Linux kernel device tree for the board can be used as is,
corresponding U-Boot device tree files are removed. U-Boot tweaks are
kept unchanged.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
The PHYCORE_IMX8MM is used by the phyBOARD-Polis and the
phyGATE-Tauri-L. Migrate both boards to OF_UPSTREAM. Linux kernel device
trees for both boards can be used as is, corresponding U-Boot device
tree files are removed. U-Boot tweaks are kept unchanged.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Remove R8A779H0 V4M DTs which are now replaced by OF_UPSTREAM counterparts.
No functional change expected.
This patch finalizes OF_UPSTREAM conversion of R8A779H0 V4M which DTs landed
in Linux 6.9 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Javier Martinez Canillas <javier@dowhile0.org> says:
Hello,
I noticed that the IGEPv2 board did not boot anymore with mainline U-Boot.
This was caused by a driver change to allocate its platform data before
relocation and U-Boot not having enough pre-relocation heap size for this.
This series fixes this issue and also makes the board support more modern,
by enabling DM for SPL and migrating the IGEP boards to use upstream DTBs.
Enable OF_UPSTREAM to use upstream DT and add a ti/omap/ prefix to the
DEFAULT_DEVICE_TREE config option.
That way, a DTS from the upstream dts/upstream/src/ directory is used
instead of the arch/$(ARCH)/dts/ directory. These in turn are removed.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Use upstream device tree files and bindings. To do so:
- imply (enable) OF_UPSTREAM option for E850-96 target
- point DEFAULT_DEVICE_TREE in E850-96 config to upstream dts
- remove now not needed local dts files, binding docs and headers
- update MAINTAINERS and board/samsung/e850-96/MAINTAINERS
correspondingly
Upstream device tree files for Exynos850 SoC and E850-96 board are
pretty much the same as local (removed) ones, so the conversion is
rather straightforward and painless in this case. The appended dts file
(arch/arm/dts/exynos850-e850-96-u-boot.dtsi) stays unchanged.
The only remaining local dt-bindings doc for E850-96 board is
exynos-pmu.yaml. It wasn't removed as it's quite different from Linux
kernel version. Particularly U-Boot local version of exynos-pmu.yaml
describes "samsung,uart-debug-1" property, which is not present in Linux
kernel binding. Later it might be upstreamed to Linux kernel, and once
it's done the U-Boot exynos-pmu.yaml binding can be removed.
No functional change.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
