Add support for building U-Boot SPL for Renesas R-Car Gen4 R8A779G0 V4H SoC.
The SPL initializes the DBSC5 DRAM controller, RT-VRAM and loads and starts
U-Boot proper on the Cortex-A76 core.
The SoC BootROM can not boot the CA76 core directly, instead the SPL starts
on the CR52 core which immediately brings up the CA76 core, which in turn
starts executing the actual SPL. This is achieved by placing a tiny bit of
precompiled Aarch32 code at the very beginning of the SPL. The code consists
of some 32 instructions, uses APMU to configure CA76 start address to offset
0x80 Bytes from start of the SPL, and uses APMU to start the CA76 core. The
code parts the CR52 core in an endless loop once the CA76 core got started.
The 32 instructions are completely arbitrary number, so is the offset 0x80
Bytes from start of SPL, because 0x80 = 128 decimal and 128 / 4 bytes per
instruction is 32 instructions. The 32 instructions turned out to be enough
to started the CA76 and 0x80 is nicely aligned.
Once the SPL completes hardware initialization, the SPL loads U-Boot proper.
The u-boot.itb proper fitImage contains 64bit build on u-boot-nodtb.bin and
a DT for R8A779G0 V4H White Hawk board and is generated by binman. The
u-boot.itb is loaded from SPI NOR offset 0x80000.
In order to install this setup on an existing R8A779G0 V4H White Hawk board,
build using r8a779g0_whitehawk_defconfig, generate SPI NOR image flash.bin
and write flash.bin to SPI NOR offset 0x0 . Finally, configure board MD pin
switches according to the R8A779G0 V4H White Hawk board documentation for
40 MHz SPI NOR boot using DMA and restart the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The U-Boot is currently not capable of handling ethernet-phy-ieee802.3-c45
PHYs correctly, and also does not handle MDIO bus wide reset-gpios property.
Until proper C45 PHY support lands in U-Boot, disable AVB1/AVB2 interfaces.
This only disables the two MACs with 88Q2110/88Q2112 100/1000BASE-T1 PHYs
on ethenet sub-board, the main board AVB0 ethernet is unaffected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RPC SPI DT node is now part of mainline Linux DT, remove the
duplicate content from U-Boot DT extras. The SPI flash DT node name
has been changed from "spi-flash@0" to "flash@0", reflect this change
in this patch. Retain "bank-width" and "num-cs" DT properties which
are used by U-Boot. Retain "spi-rx-bus-width" and "spi-tx-bus-width"
DT properties to indicate the bus should always be operated in 1-1-1
mode as the U-Boot RPC SPI driver does not support higher bus width
modes yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The U-Boot build system can automatically paste -u-boot.dtsi at the
end of matching .dts during build. Stop emulating this behavior and
rename the -u-boot.dts files to -u-boot.dtsi, drop "#include...dts"
from those new u-boot.dtsi files, and update board configuration
accordingly.
The rename, '#include...dts` scrubbing and configuration update has
been done using the following script:
```
$ find . -name r[78]\*-u-boot.dts | sort -u | while read line ; do \
git mv ${line%-u-boot.dts}-u-boot.dts ${line%-u-boot.dts}-u-boot.dtsi ; \
done
$ sed -i '/^#include.*dts"/ d' `find . -name r[78]\*-u-boot.dtsi`
$ sed -i 's@-u-boot@@g' `git grep -li renesas configs`
```
The Salvator-X and ULCB board files have been updated manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com>
