The SPI flash node has been added in upstream DT, drop all props beside
bootph-* props from the SPI flash related nodes in u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-pinephone-pro device tree from Linux kernel v6.8.
Add SPI flash related node and options to support boot from SPI flash.
Remove REGULATOR_PWM=y, board does not use pwm-regulator compatible.
Add SYS_NS16550_MEM32=y to use readl/writel for serial console.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove superfluous bootph-all props already inherited from main soc
u-boot.dtsi file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A lot of RK3399 boards use a u-boot,spl-boot-order of "same-as-spl",
&sdhci and &sdmmc.
Move this to rk3399-u-boot.dtsi and make this default for boards
currently missing a u-boot,spl-boot-order prop.
Before commit a7e69952eb6d ("rockchip: spl: Cache boot source id for
later use") it was required to include the SPI flash node in the
u-boot,spl-boot-order prop to successfully load FIT from SPI flash.
The SPI flash node reference has been dropped from spl-boot-order from
pinebook-pro, roc-pc and rockpro64 now that "same-as-spl" also gets
resolved to the SPI flash node and loading FIT from SPI flash works
without having the node explicitly referenced in spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399 SoC contain a crypto engine block that can generate random
numbers.
Imply DM_RNG and RNG_ROCKCHIP Kconfig options to take advantage of the
random generator on all RK3399 boards. Also remove the unnecessary use
of a status = "okay" prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
