Since commit 6007b69d544e ("rockchip: rk3399-puma: Update SPL_PAD_TO
Kconfig option"), SPL_PAD_TO matches
(CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR - 64) * 512 and the default
value for simple-bin:fit:offset in rockchip-u-boot.dtsi is
SPL_PAD_TO, so let's remove this override.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Sync rk3399-puma related device tree from Linux kernel v6.8.
The vdd_log node is already part of rk3399-puma.dtsi, only keep the
regulator-init-microvolt prop in u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes
with bootph props. Also move bootph for common nodes shared by all
boards to the SoC u-boot.dtsi.
eMMC, SD-Card and SPI flash nodes are also changed to only be tagged
with bootph props for SPL and U-Boot pre-reloc phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The initial serial console UART iomux is typically configured in
board_debug_uart_init() at TPL stage on Rockchip platform.
Later stages typically use pinctrl driver to configure iomux UART once
again based on the control FDT.
Include uart related pinctrl nodes in TPL/SPL control FDT to make it
possible for pinctrl driver to configure UART iomux at TPL/SPL stage.
Following debug log message may also be seen at U-Boot pre-reloc stage:
ns16550_serial serial@ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
This can be resolved by including bootph prop for U-Bood pre-reloc
phase (bootph-some-ram or bootph-all). However, this has intentionally
been excluded due to including it unnecessarily slows down boot around
200-400 ms.
Also add the clock-frequency prop similar to what has been done for
other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3399-puma is the only supported board that use uart0 for serial
console, other RK3399 boards typically use uart2 for serial console
and may use uart0 for bluetooth.
Move setting bootph prop to board u-boot.dtsi to only include the uart0
node in TPL/SPL control FDT for the rk3399-puma target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the required binman images to replace the Makefile rules which are
currently used. This includes subsuming:
- tpl/u-boot-tpl-rockchip.bin if TPL is enabled
- idbloader.img if either or both of SPL and TPL are enabled
- u-boot.itb if SPL_FIT is enabled
- u-boot-rockchip.bin if SPL is used, either using u-boot.itb when
SPL_FIT is enabled or u-boot.img when it isn't
Note that the intermediate files are dropped with binman, since it
producing everything in one pass. This means that
tpl/u-boot-tpl-rockchip.bin is not created, for example.
Note that for some 32-bit rk3288 boards, rockchip-optee.dtsi is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
The GPT table is taking the first 34 sectors, which amounts to 0x4400
bytes. Saving the environment below this address in storage will corrupt
the GPT table.
While technically the table ends at 0x4400, some tools (e.g. bmaptool)
are rounding everything to the logical block size (0x1000), so it is
safer to make it point to 0x5000 so that the environment could still
persist when flashing a sparse image with bmaptool or similar tools.
Obviously, the default 0x4000 environment size does not work anymore, so
let's set it to 0x3000 so it does fill the gap between the GPT table
(rounded to 0x1000) and the start of the idbloader.img.
Fixes: 56f580d3eb8d ("rockchip: dts: rk3399-puma: put environment (in MMC/SD configurations) before SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Now that a single binary containing TPL/SPL correctly formatted for SPI
flashes and U-Boot proper, can be generated by binman, let's do it.
Also update the documentation to tell the user to use this newly
generated file instead of manually generating and flashing the binaries.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The offset of the SPL payload on Puma is different than for other
Rockchip devices in that it is stored at offset 256K instead of much
further away in the MMC.
Flashing one binary instead of two at different offsets is much more
user friendly so let's migrate to it by modifying the offset in the Puma
specific Device Tree.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Depending on the toolchain used to compile the SPL for Puma RK3399-Q7
module, the board does not boot because the resulting binary is too big
to fit in SRAM.
Let's add a TPL so that there's no need to fiddle with or hack the
defconfig to have a working bootloader.
This follows what's been done for the majority of other RK3399-based
boards.
See the original commit for the first migrations:
bdc00080111f "rockchip: rk3399: update defconfig for TPL"
Unfortunately, the offset in SPI-NOR for U-Boot proper needs to be
modified, since the move from SPL to TPL+SPL for idbloader.img (and the
"only the first 2KB per 4KB blocks are written" "hack" for rkspi format)
increased the size above 256KB. Let's move it to 512KB to, hopefully, be
safe.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Trying to load U-Boot proper from SPL when SPL was not loaded from
SD-Card is currently not working because the SDMMC pins aren't muxed
correctly. It is assumed the BootROM is doing this for us when booting
from SD-Card hence why it's not needed when booting TPL/SPL from
SD-Card.
The pinctrl properties are removed from the SPL DT property removal list
and the pinctrl configuration nodes made available in the SPL DT, in
addition to the pull-up configurations to allow loading U-Boot proper
from SD-Card as a fallback mechanism for SPI-NOR and eMMC.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force
booting from SD card or USB via rkdeveloptool by toggling a switch. This
switch needs to be overridden in software to be able to access eMMC and
SPI-NOR once the device has booted from SD Card. Puma SoM can override
this pin via gpio3_d5.
Until now, fixed regulator device was abused to model this, but since
there's now support for GPIO hogs, let's use it.
Since we want to be able to boot the SPL from SD Card but give it the
ability to load U-Boot proper from a fallback medium such as eMMC and
SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for
other kinds of regulators are not needed anymore, so let's disable them.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.
Fixes: 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0. Formerly the alias spi1
pointed to &spi5, use an alias spi5 for this instead.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
