JH7110 SoC requires no specific handling before entering Linux kernel.
Let's drop the specific implementation to avoid duplication.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The current implementation is equivalent to the fallback one, so
this shouldn't change any behaviour but cleans the code up only.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Most RISC-V SoCs have similar cleanup_before_linux() functions. Let's
provide a weak symbol as fallback to reduce duplicated code.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following diagram illustrates the boot flow for OP-TEE OS
initialization on RISC-V.
(1)-----------+
| U-Boot SPL |
+------------+
|
v
(2)-------------------------------------------------------------+
| OpenSBI (fw_dynamic.bin) |
| (4)------------------------+ |
| | optee dispatcher driver | |
+-----------------+-------^---------|-------+------------------+
M-mode | | |
---------+--[trusted domain]---+----.----+--[untrusted domain]-------
S-mode | (coldboot domain) | | |
v | | v
(3)---------------------------+ |(5)----------------------------+
| OP-TEE OS (tee.bin) | | | U-Boot (u-boot-nodtb.bin) |
+----------------------------+ | +-----------------------------+
| |
| v
|(6)----------------------------+
| | Linux |
| +-----------------------------+
This patch enables the inclusion of the OP-TEE binary within the
U-Boot ITB, allowing it to be loaded to a platform defined address
by U-Boot SPL.
Signed-off-by: Yu-Chien Peter Lin <peter.lin@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Allow specifying load address of OP-TEE binary. It is
recommended that the specified address aligns with the
base address of an PMP-protected NAPOT region and matches
the CFG_TDDRAM_START configuration in OP-TEE.
Signed-off-by: Yu-Chien Peter Lin <peter.lin@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If CONFIG_AVAILABLE_HARTS=y, variable available_harts_lock is created in
the data section which will not be writable while executing from flash.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Implement functionality to probe and calculate the DRAM size
during the boot phase for the RISC-V spacemit K1 platform.
Tested-by: Marcel Ziswiler <marcel@ziswiler.com> # BPI-F3 16G
Signed-off-by: Huan Zhou <me@per1cycle.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The fields SizeOfCode, SizeOfInitializedData, and SizeOfUninitializedData
are define in the PE-COFF specification [1].
* SizeOfCode must match the size of all .text sections.
* SizeOfInitializedData must match the size of all .data sections.
* SizeOfUninitializedData must match the size of all .bss sections.
We only have one .text and one .data section. SizeOfCode and
SizeOfInitializedData have to be calculated as the difference between
the end and the start of the respective section.
As we don't have any .bss sections in the generated EFI binaries.
SizeOfUninitializedData must remain 0.
[1] https://learn.microsoft.com/en-us/windows/win32/debug/pe-format
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Except for the architecture specific lines ARM and RISC-V can use the same
linker script. Move the common lines to an include.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add Canaan K230 SoC with sysreset support, running without cache
enabled.
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update the cpu probing to fallback to "riscv,isa" property if
"riscv,isa-extensions" is not available and modify the riscv CMO code
to use the block size that was probed during cpu setup.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enhance the existing extension probing mechanism by adding support for
more extensions and probing using the "riscv,isa" property. This patch
is ported from the latest upstream linux.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Split out StarFive VisionFive2 multi-board target specific configuration
into starfive-visionfive2-binman.dtsi in preparation for removal of
jh7110-u-boot and jh7110-common-u-boot in part or whole as sent upstream.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Andrew Goodbody <andrew.goodbody@linaro.org> says:
Picking up a series from Dan Carpenter and applying requested
changes for v2.
I had previously set CONFIG_64BIT for arm64. This patchset does the
same thing for sandbox and x86_64. (Mips and riscv were already
doing it). This CONFIG option is used in the Makefile to determine
if it's a 32 or 64 bit system for the CHECKER.
Makefile
1052 # the checker needs the correct machine size
1053 CHECKFLAGS += $(if $(CONFIG_64BIT),-m64,-m32)
Link: https://lore.kernel.org/r/20241216180736.1933807-1-andrew.goodbody@linaro.org
Select CONFIG_64BIT so that we pass the -m64 option (instead of -m32) to
static analysis tools.
Introduce CONFIG_SPL_64BIT and select it for architectures other than
x86 with 64 bit builds. Do not select it for x86 builds as x86 uses
a 32 bit SPL.
Ensure that when limits are set they use CONFIG_64BIT for U-Boot
proper and CONFIG_SPL_64BIT for SPL. This is to allow for the 32 bit
SPL build used by x86.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Add basic support for SpacemiT's Banana Pi F3 board.
Update the k1.dtsi align with mainline.
Note that the device tree files follow the mainline Linux source[1].
Links: https://patches.linaro.org/project/linux-serial/patch/20240730-k1-01-basic-dt-v5-8-98263aae83be@gentoo.org/ [1]
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Signed-off-by: Huan Zhou <pericycle.cc@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Add SDHCI and EMMC controlles nodes on TH-1520 SoC. And enable them for
Lichee module 4A.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
The imply statements should be sorted in the sequence
of appearance in .config.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Support multiple DTBs for JH7110 based boards, so they can
select the correct DT at runtime.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
To support the other JH7110 based boards, add u-boot
device tree for them.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: H Bell <dmoo_dv@protonmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
To support JH7110 based boards besides v1.3B,
add a common dtsi and add common code to it.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Add u-boot features to the U-Boot device tree.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: E Shattow <lucent@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Enable OF_UPSTREAM to use upstream DT and add starfive/ prefix to
the DEFAULT_DEVICE_TREE. Rename jh7110-starfive-visionfive-2-u-boot.dtsi
to jh7110-starfive-visionfive-2-v1.3b-u-boot.dtsi and set the v1.3b
device tree as the default device tree.
Drop redundant DT files from arch/riscv/dts/ and redundant clock and
reset definitions from include/dt-bindings/.
Since the old clock definitions is a little different from those in
upstream Linux, update the clock definitions in clock drivers
accordingly.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Import a slightly modified version of the LicheeRV Nano and SG2002
device trees from the Linux Kernel. The current supported IPs are UART,
MMC, Timer, PLIC and CLINT.
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
This replaces dm_remove_devices_flags() calls in all boot
implementations to ensure non vital devices are consistently removed
first. All boot implementation except arch/arm/lib/bootm.c currently
just call dm_remove_devices_flags(DM_REMOVE_ACTIVE_ALL). This can result
in crashes when dependencies between devices exists. The driver model's
design document describes DM_FLAG_VITAL as "indicates that the device is
'vital' to the operation of other devices". Device removal at boot
should follow this.
Instead of adding dm_remove_devices_flags() with (DM_REMOVE_ACTIVE_ALL |
DM_REMOVE_NON_VITAL) everywhere add dm_remove_devices_active() which
does this.
Fixes a NULL pointer deref in the apple dart IOMMU driver during EFI
boot. The xhci-pci (driver which depends on the IOMMU to work) removes
its mapping on removal. This explodes when the IOMMU device was removed
first.
dm_remove_devices_flags() is kept since it is used for testing of
device_remove() calls in dm.
Signed-off-by: Janne Grunau <j@jannau.net>
The commit 7576ab2facae ("riscv: Add support for AMD/Xilinx MicroBlaze V")
added support for 32bit version. 64bit version is also available that's why
wire it up too.
DT is providing description for generic QEMU target.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The U-Boot copy of the mpfs devicetree has, in general, been neglected
somewhat in comparison to the one in Linux. Moving to OF_UPSTREAM to
keep both in sync should serve to eliminate that discrepancy.
Additionally, moving to OF_UPSTREAM will let U-Boot automatically pick
up the devicetree rework that is in progress at [1].
Link: https://lore.kernel.org/all/20241002-private-unequal-33cfa6101338@spud/ [1]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
If we take an exception before u-boot is relocated, there's a good
chance we will end up in an endless loop of exceptions because resume is
invalid until after relocation.
Signed-off-by: Anton Blanchard <antonb@tenstorrent.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Align U-Boot with QEMU amd-microblaze-v-virt platform to be able to wire
it with CI.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Padmarao Begari <padmarao.begari@amd.com>
Define CBO inval and flush instructions and use those for the
dcache inval and flush operations respectively.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add insn-def.h which is similar to that in linux and contains the macros
to generate any instruction of type 'I' using the assembler's .insn
directive.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
* Messages written with log_err() should be terminated with linefeed.
* Spell device-tree with hyphen as elsewhere in U-Boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch series enables full RVVM virtual machine support which was
earlier inconveniently provided as out-of-tree patchset.
This should be cleaner than a separate board config, since both
emulators provide similar feature set.
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The SBI 3.0 specification [1] adds the following extensions:
* Firmware Features Extension
* Message Proxy Extension
Let the sbi command detect their availability.
The Firmware Features Extension is already implemented in OpenSBI.
Correct the text for the DBTR extension and move it to the same position
as in the specification.
[1] https://github.com/riscv-non-isa/riscv-sbi-doc/releases/download/vv3.0-rc1/riscv-sbi.pdf
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The dtbs: target is almost identical in all architecture Makefiles.
All architecture Makefiles include scripts/Makefile.dts . Deduplicate
the dtbs: target into scripts/Makefile.dts . No functional change.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org> #qcom, OF_UPSTREAM
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is not actually a command so the name is confusing. Use
BOOTEFI_HELLO_COMPILE instead. Put it in the efi_loader directory
with the other such config options.
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add driver for AST2700 to initialize DRAM in SPL.
This patch also refactors the Kconfig dependency of
Aspeed DRAM drivers as some of them are shared among
the file structures of RV and ARM ISAs.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Define and parse the header of the First Mutable Code (FMC)
of AST2700 SoCs at runtime phase.
The FMC header contains the information to load prebuilt binaries
required for device initialization such as DRAM and VGA.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The _image_binary_end symbol was aligned to the 8-bytes boundary.
However, the SPL device tree (u-boot-spl.dtb) is concatenated right
after the binary (u-boot-spl-nodtb.bin) wihtout the consideration of
the 8-bytes alignment restriction.
After then, for the SPL_SEPARATE_BSS case, fdtdec_setup() searching
for the DTB by _image_binary_end will return the "Missing DTB" error.
As the real DTB starting point does not align to a 8-bytes address
like _image_binary_end does.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add prompt for STACK_SIZE_SHIFT to make it configurable.
The default value remains 14 as usual.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Make the Atomic (A) ISA extension selectable. Thus CPUs such as
Ibex without the A extension can be supported.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
