Allow specifying load address of OP-TEE binary. It is
recommended that the specified address aligns with the
base address of an PMP-protected NAPOT region and matches
the CFG_TDDRAM_START configuration in OP-TEE.
Signed-off-by: Yu-Chien Peter Lin <peter.lin@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If CONFIG_AVAILABLE_HARTS=y, variable available_harts_lock is created in
the data section which will not be writable while executing from flash.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add Canaan K230 SoC with sysreset support, running without cache
enabled.
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Andrew Goodbody <andrew.goodbody@linaro.org> says:
Picking up a series from Dan Carpenter and applying requested
changes for v2.
I had previously set CONFIG_64BIT for arm64. This patchset does the
same thing for sandbox and x86_64. (Mips and riscv were already
doing it). This CONFIG option is used in the Makefile to determine
if it's a 32 or 64 bit system for the CHECKER.
Makefile
1052 # the checker needs the correct machine size
1053 CHECKFLAGS += $(if $(CONFIG_64BIT),-m64,-m32)
Link: https://lore.kernel.org/r/20241216180736.1933807-1-andrew.goodbody@linaro.org
Select CONFIG_64BIT so that we pass the -m64 option (instead of -m32) to
static analysis tools.
Introduce CONFIG_SPL_64BIT and select it for architectures other than
x86 with 64 bit builds. Do not select it for x86 builds as x86 uses
a 32 bit SPL.
Ensure that when limits are set they use CONFIG_64BIT for U-Boot
proper and CONFIG_SPL_64BIT for SPL. This is to allow for the 32 bit
SPL build used by x86.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Add basic support for SpacemiT's Banana Pi F3 board.
Update the k1.dtsi align with mainline.
Note that the device tree files follow the mainline Linux source[1].
Links: https://patches.linaro.org/project/linux-serial/patch/20240730-k1-01-basic-dt-v5-8-98263aae83be@gentoo.org/ [1]
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Signed-off-by: Huan Zhou <pericycle.cc@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Define CBO inval and flush instructions and use those for the
dcache inval and flush operations respectively.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch series enables full RVVM virtual machine support which was
earlier inconveniently provided as out-of-tree patchset.
This should be cleaner than a separate board config, since both
emulators provide similar feature set.
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add prompt for STACK_SIZE_SHIFT to make it configurable.
The default value remains 14 as usual.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Make the Atomic (A) ISA extension selectable. Thus CPUs such as
Ibex without the A extension can be supported.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If an exception occurs in main U-Boot, show the registers. This makes
analyzing crashes especially in external applications easier.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To minimize SPL size it is reasonable to disable SHOW_REGS. For main U-Boot
the size restrictions are much more relaxed.
* Provide separate Kconfig symbols for SPL and main U-Boot.
* Add a help text.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The CONFIG_SPL_FRAMEPOINTER symbol is only relevant in SPL.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Ben Dooks <ben.dooks@codethink.co.uk>
When virtio_init() gets called from board_init() PCI isn't ready. Thus,
virtio-over-PCI (e.g. network interfaces) devices can't be detected and
used without additional `virtio scan` scan in the shell or a script.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add Sophgo cv1800b SoC to support RISC-V arch.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When debugging, it is useful to have a backtrace to find
out what is in the call stack as the previous function (RA)
may not have been the culprit.
Since this adds size to the build, do not add it by default
and avoid putting it in the SPL build if not needed.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Leo Yu-Chi Liang <ycliang@andestech.com>
These configs are used in multiple places so put them in a shared
Kconfig file.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Sophgo's Milk-V Duo board, only minimal device tree and
serial console are enabled, and it can boot via vendor first stage
bootloader.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Clean things up for the next time somebody adds a target.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Similar change was done by commit b4c2c151b14b ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
This patch adds ISA string to the -march to generate zbb instructions
for U-Boot binaries, along with optimized string functions introduced
from Linux kernel.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Introduce common Kconfig symbol for riscv architecture.
This symbol SPL_LOAD_FIT_OPENSBI_OS_BOOT is like falcon mode on ARM,
the Falcon boot is a shortcut boot method for SD/eMMC targets. It
skips the loading the RAM version U-Boot. Instead, it will loads
the FIT image and boots directly to Linux.
When SPL_OPENSBI_OS_BOOT is enabled, linux.itb is created after
compilation instead of the default u-boot.itb. It initialises memory
with the U-Boot SPL at the first stage, just as a normal boot process
does at the beginning. Instead of jumping to the U-Boot proper from
OpenSBI before booting the Linux kernel, the RISC-V falcon mode
process jumps directly to the Linux kernel to gain shorter booting time.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most boards don't enable the pre-console buffer. So we will not see any
early messages. OpenSBI 1.3 provides us with the debug console extension
that can fill this gap.
For S-Mode U-Boot enable CONFIG_DEBUG_UART by default.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Multiple revisions of the StarFive VisionFive 2 board exist. They can be
identified by reading their EEPROM.
Linux uses two differently named device-tree files. To load the correct
device-tree we need to set $fdtfile to the device-tree file name that
matches the board revision.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Add a Kconfig item to allow SPL to clear stack/GD/malloc area before
using them.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's
TH1520 SoC, only minimal device tree and serial console are enabled,
so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
As the RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, we rename SiFive CLINT to RISC-V
ALINT in the source tree to be future-proof.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint ipi driver to
support ACLINT mswi device, by checking the per-driver data field of
the ACLINT mtimer driver to determine whether a syscon based approach
needs to be taken to get the base address of the ACLINT mswi device.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Describe that CONFIG_SBI_V02=y does not mean SBI specification v0.2
but v0.2 or later.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The riscv32 toolchain for GCC-12 provided by kernel.org contains libgcc.a
compiled for double-float. To link to it we have to adjust how we build
U-Boot.
As U-Boot actually does not use floating point at all this should not
make a significant difference for the produced binaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In SMP all harts will register themself in available_hart
during start up. Then main hart will send IPI to other harts
according to this variables. But this mechanism may not
guarantee that all other harts can jump to next stage.
When main hart is sending IPI to other hart according to
available_harts, but other harts maybe still not finish the
registration. Then the SMP booting will miss some harts finally.
So let it become an option and it will be enabled by default.
Please refer to the discussion:
https://www.mail-archive.com/u-boot@lists.denx.de/msg449997.html
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
U-Boot and SPL don't necessary share the same location, so we might end
with U-Boot SPL in read-only memory (XIP) and U-Boot in read-write memory.
In case of non XIP boot mode, we rely on such variables as "hart_lottery"
and "available_harts_lock" which we use as atomics.
The problem is that CONFIG_XIP also propagate to main U-Boot, not only SPL,
so we need CONFIG_SPL_XIP to distinguish SPL XIP from other XIP modes.
This adds an option special for SPL to behave it in XIP manner and we don't
use hart_lottery and available_harts_lock, during start proccess.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
When trying to run qemu-riscv64_smode_defconfig with 32 harts booting
fails. The debug UART shows a message
alloc space exhausted
32 is the current maximum number of harts for machine virt in QEMU 7.0.
Raise the default for SYS_MALLOC_F_LEN to 16 KiB.
Move the setting to /Kconfig where we define SYS_MALLOC_F_LEN for
other architectures too.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The enable_caches is a generic hook for architecture-implemented, we
define this function to enable composable cache of sifive platforms.
In sifive_cache, it invokes the generic cache_enable interface of cache
uclass to execute the relative implementation in SiFive ccache driver.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the SYS_CACHE_SHIFT_N options from arch/arm/Kconfig to
arch/Kconfig, and introduce SYS_CACHE_SHIFT_4 to provide a size of 16.
Introduce select statements for other architectures based on current
usage. For MIPS, we take the existing arch-specific symbol and migrate
to the generic symbol. This lets us remove a little bit of otherwise
unused code.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Leo <ycliang@andestech.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Currently all assembly optimized implementation of memory routines
show up at the top level of the RISC-V architecture Kconfig menu.
Let's group them together into a submenu.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
