The phyCORE-i.MX 93 is available in various variants. Relevant variant
options for the spl/u-boot are:
- with or without HS400 support for the eMMC
- with 1GB ram chip, or 2GB ram chip
The phyCORE's eeprom contains all information about the existing variant
options. Add evaluation of the eeprom data to the spl/u-boot to
enable/disable HS400 and to select the appropriate ram configuration at
startup.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Wadim Egorov <w.egorov@phytec.de> says:
Changes in v2:
- Reabse to current next
- Add Tested-by: John Ma <jma@phytec.com>
- Add Kconfig option to select RAM size statically
- Make board/phytec/common/k3 always compile for CONFIG_ARCH_K3
v1: https://lists.denx.de/pipermail/u-boot/2024-May/553057.html
Introduce fdt_apply_ddrss_timings_patch() to allow board code to
override DDR settings in the device tree prior to DDRSS driver probing.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: John Ma <jma@phytec.com>
This API is based on a block structure with a 8 Byte large
API v3 header and various of different blocks following. It extends
our current API v2, which is always 32 Byte large, and is located
directly after v2.
Add the MAC block as first block type. It contains the physical
Ehternet interface number, a MAC address and a CRC checksum over the
MAC payload.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Environment handling code can be reused across all our K3 based SoMs.
Instead of adding the same code for every new SoM, move it to a common
board.c file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Add all functions to read each SOM option from the EEPROM
image and detect whether it's the correct product for this
image.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Commit aa7858fe5e2e ("board: phytec: som_detection: move definitions to
source file") moved function definitions from header to source file.
Makefile however was not updated to unconditionally (from
[..]_SOM_DETECTION) build the imx8 and phytec som detection units.
Also remove unused includes that cause build failures on arm 32bit
boards. SoM detection shall support 32bit boards as well, but arch
specific code should not be included in the generic module.
Fixes: aa7858fe5e2e ("board: phytec: som_detection: move definitions to source file")
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Add imx8m specific detection part. Which includes checking the
EEPROM data for article number options.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Recent shipped PHYTEC SoMs come with an i2c EEPROM containing
information about the hardware such as board revision and variant.
This can be used for RAM detection and loading device tree overlays
during kernel start.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
