The phyCORE-i.MX 93 is available in various variants (e.g. different ram
sizes, eMMC HS400 yes/no). Enable hardware introspection for the
imx93-phyboard-segin_defconfig, so that during startup the SOM module
variant can be detected, and the hardware can be configured accordingly.
The resulting SPL and u-boot binary shall able to boot each
phyCORE-i.MX 93 module variant on each carrier board. Finally rename
imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight
its SOM scope.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
The phyCORE-i.MX 93 is available in various variants. Relevant variant
options for the spl/u-boot are:
- with or without HS400 support for the eMMC
- with 1GB ram chip, or 2GB ram chip
The phyCORE's eeprom contains all information about the existing variant
options. Add evaluation of the eeprom data to the spl/u-boot to
enable/disable HS400 and to select the appropriate ram configuration at
startup.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
The phyCORE-i.MX 93 is available with a 1GB ram chip or a 2GB ram chip.
Add the ram timings for the 2GB chip, in form of a diff compared
to the existing LPDDR4X 1GB timings. With that, the SPL can select the
appropriate timings at startup.
Update also the 1GB ram timings with new version of the DDR Tool.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Tested-by: Primoz Fiser <primoz.fiser@norik.com>
Since we use SPEED GRADE fuse to set A55 frequency, remove the
set_arm_core_low_drive_clk function which has hard coded frequency.
And adjust clock_init called sequence and split it to early and late
functions.
Set the authen register in early function, because CCF driver checks
NS bit.
Set bus and core clock in late function, because the fuse read and
SoC type/rev depend on ELE.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Rename existing environment variables according to the bootstd doc.
Renamed variables are fdto_addr, bootenv_addr, fdt_addr and
fdt_file.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Include the common overlays env file for phycore_imx93.
The common overlays env file supports disabling loading overlays by
setting the no_overlays variable.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The following information printed on every boot is not very
helpful for the users:
SOC: 0xa0009300
LC: 0x40040
Move them to debug() level.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Mathieu Othacehe <othacehe@gnu.org>
Put imx9_probe_mu declaration in a new mu.h header file.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
