update MAINTAINERS file, add some more board maintainers.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
The signal integrity test generates pattern on DDR lines
for certification. The signals must be as fast as possible
and unidirectional.
The test is required from our HW team. The available
u-boot memory test doesn't full fill the our requirements.
The test is planed to be used in all new siemens boards.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add siemens specific memory test. Enable it through Kconfig option
SPL_CMT. The test is required from our HW team. It runs over
temperature during many days:
* must run indefinitively through the *whole* DDR area,
so we cannot use linux memtest for example.
* must write/read/check all values
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
The eeprom contains the information on which module
we are running, so read it from the eeprom and print
it on the console.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Get the memory region information from system controller to reduce the
number of platform specific headers. We were aligned on NXP mek board
implementation. This need at least 1 header per memory configuration.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add the HW version read directly from EEPROM.
EEPROM chip data structure is now in a .h file common to draco
and capricorn.
Therefore move out the definitions in draco board to siemens
common place.
From: Alessandro Zini <alessandro.zini@siemens.com>
Signed-off-by: Alessandro Zini <alessandro.zini@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
with newest SCFW build_info() works now, so call it
from checkboard() now.
As we only use uart2 as console, do not init uart0.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Boards which use DCD data in SCFW can drop SPL.
We tried in our mainline rework to use this approach
too as other imx8qxp boards do in mainline. But we
failed ... it was a hard way to understand the
reason!
We cannot use DCD image in container as the SCFW
from siemens, does the RAM init on boot itself!
Siemens SCFW reads the RAM config from i2c eeprom and
dependent on this settings, initializes the RAM.
Adding DCD data to the bootcontainer will result in
hang of the SCFW, also DCD data in container image is
static which do not fit our needs.
So we must drop DCD data image, and this has the side
effect that we need SPL, as the task which loads the images
from the container only loads the images to addresses,
and if executed bit is set, starts them.
As now RAM is not initialized from it, and there is no
option to "wait until SCFW has setup RAM", we can only
load SPL into internal RAM at this point, as than SPL
and SCFW boot parallel.
The SPL itself then uses the SCU API to communicate
with the SCFW and it seems that SCFW only responds to
this API requests when RAM setup is already done by the
SCFW, which has a side-effect of a "sync" for the RAM
setup is done by SCFW!
We checked if SPL is always save in accessing RAM for
loading images to it! For tests, we added in our RAM
init part in the SCFW long delays (10 seconds and more)
as we thought there is such a sync missing, and we can
break the board through delaying RAM setup... but we
did not managed to fail booting U-Boot from SPL!
Signed-off-by: Heiko Schocher <hs@denx.de>
We have many HW with capricorn i.MX8X boards. The difference in u-boot is
at all by the display of the LEDs.
* put upstream a reference project & board for DT and defconfig
* use the capricorn prefix outside the board/siemens/capricorn folder
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this board vendor directory and when needed
add missing include files directly.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
Since we have boards using the driver model or not for i2c, use abstraction
function to probe the i2c, check the EEPROM and read from EEPROM.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Move the I2C and EEPROM address definitions in common board header.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
1. Convert all linker symbols to char[] type so that we can get the
corresponding address by calling array name 'var' or its address
'&var'. In this way, we can avoid some potential issues[1].
2. Remove unused symbol '_TEXT_BASE'. It has been abandoned and has
not been referenced by any source code.
3. Move '__data_end' to the arch x86's own sections header as it's
only used by x86 arch.
4. Remove some duplicate declared linker symbols. Now we use the
standard header file to declare them.
[1] This patch fixes the boot failure on MIPS target. Error log:
SPL: Image overlaps SPL
Fixes: 1b8a1be1a1f1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is empty, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imx8image => imx/mkimage/imx8image.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
