Get product ID and the other information from EEPROM, use them to select
the correct DTB.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
The prefix "SPL_" is not needed when using CONFIG_IS_ENABLED().
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: 5ecf9b0b8a75 ("board: starfive: add StarFive VisionFive v2 board support")
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
As OF_UPSTREAM is implemented, these code are redundant.
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: E Shattow <lucent@gmail.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Milk-V Mars vendor board support package has value 0xa (multiplier=150) for both
rx and tx delay. Upstream Linux has this as 1500 for both rx and tx delay. There
is no documentation for why this should remain 1900 so correct it now. Mars CM
and Mars CM Lite follow the same network phy delay values as Mars in the vendor
board support package.
Fixes: 92db23f7660de5897c8e3b91489b5b5780ffcd16
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Fix bad delay values copied from vendor board support package of Star64, improves
performance and reliability of bottom network port.
Fixes: 7ebf7e77c0616ef0d2f58cc1684c230f656bd3d6
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For the Milk-V Mars CM (lite) we have only been copying sizeof(void *)
bytes to the compatible property instead of the whole string list.
Fixes: de3229599d4f ("board: add support for Milk-V Mars CM")
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Similar to the Milk-V Mars, The Star64 board contains few differences to the
VisionFive 2 boards, so can be part of the same U-boot build.
Signed-off-by: Henry Bell <dmoo_dv@protonmail.com>
Cc: ycliang@andestech.com
Cc: heinrich.schuchardt@canonical.com
Reviewed-by: E Shattow <lucent@gmail.com>
We already support the VisionFive 2 and the Milk-V Mars board by
patching the VisionFive 2 device tree. With this patch the same
is done for the Milk-V Mars CM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: E. Shattow <lucent@gmail.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Rename spl_soc_init() to spl_dram_init() because the generic function
name does not reflect what the function actually does. Also
spl_dram_init() is commonly used for dram initialization and should be
called from board_init_f().
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The usage of common.h is deprecated. Remove it from board files.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The differences between the Milk-V Mars board and the VisionFive 2 board
are small enough that we can support both using the same U-Boot build.
* The model and compatible property are taken from proposed Linux patches.
* The EEPROM is atmel,24c02 according to the vendor U-Boot.
* The second Ethernet port is not available.
usb@10100000 does not exist in U-Boot yet. So we don't have to reflect
differences in usage here.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Configure the pad drive strength register for both PHYs.
The values correspond to what can be found in the Linux DTS
for VisionFive2 v1.3b.
Pad drive strength configuration is required for the phy0 to work correctly
with 100Mbit links.
Signed-off-by: Lukasz Tekieli <tekieli.lukasz@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between the StarFive VisionFive 2 1.2A and 1.3B boards is
handled dynamically by looking at the PCB version in the EEPROM in order
to have a single u-boot version for both versions of the board. While
the "model" property is correctly handled, the "compatible" one is
always the the one of version 1.3b.
This patch add support for dynamically configuring that property.
Fixes: 9b7060bd15e7 ("riscv: dts: jh7110: Combine the board device tree files of 1.2A and 1.3B")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
JTAG pins are mapped as below. To access the JTAG pins, we need to
control the GPIO pins from SPL which seems to be the earliest stage for
JTAG.
- JTAG nTRST: GPIO36 / Input
- JTAG TDI: GPIO61 / Input
- JTAG TMS: GPIO63 / Input
- JTAG TCK: GPIO60 / Input
- JTAG TDO: GPIO44 / Output
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Very few of the existing event-spy records use the arguments they are
passed. Update them to use a simple spy instead, to simplify the code.
Where an adaptor function is currently used, remove it where possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
The main difference between StarFive VisionFive 2 1.2A and 1.3B is gmac.
You can read the PCB version of the current board by
get_pcb_revision_from_eeprom(), and then dynamically configure the
difference of gmac in spl_perform_fixups() according to different PCB
versions, so that one DT and one defconfig can support both 1.2A and
1.3B versions, which is more user-friendly.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
