It turns out only Puma had a working git:// URL. Though that is now
fixed, having HTTPS URLs make it easier to directly reach our cgit
webserver to check what's up without having to change the URL manually.
Depending on your terminal settings, this also makes it possible to
open the link from it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Most of the current URLs should be redirected but some aren't already,
so let's anticipate more IT hiccups by migrating to new URLs.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
See
https://embedded.cherry.de/theobroma-systems-is-now-officially-part-of-cherry-se/
While the mail addresses on the theobroma-systems.com domain should be
redirect to cherry.de, let's anticipate IT hiccups and avoid important
mails not reaching us by swapping the domain name wherever appropriate
for the newer one.
Christoph Mueller isn't working at ~Theobroma~ CHERRY Embedded Solutions
anymore, but I don't know his new mail address so mails destined to him
will keep bouncing.
Cc: Heiko Stuebner <heiko.stuebner@cherry.de> <heiko.stuebner@theobroma-systems.com>
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@cherry.de>
Cc: Klaus Goger <klaus.goger@cherry.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The STM32_RST line is routed to the ATtiny microcontroller
PA0/RESET/UPDI pin. By driving the PX30 SoC pin as GPIO output high, we
prevent external UPDI to be used for flashing without first putting this
pin as GPIO input, an extra step we could avoid in userspace.
There's an external hardware pull-up strong enough to keep the STM32_RST
state high on ATtiny side but weak enough it can be overridden by
external UPDI. This also means it is safe to use for the STM32 variant,
where STM32_RST line will be in the same state as if output high was
used.
The Q7 standard specifies that MFG_NC1 and MFG_NC2 (used for UPDI for
Ringneck) pins should neither be driven by the carrierboard, nor have
pull-up or pull-down resistors. This means this commit is safe to use
regardless of the carrierboard this module would be connected to
(provided it follows the Q7 standard).
Fixes: 6acdd63e8771 ("rockchip: ringneck-px30: always reset STM32 companion controller on boot")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The original link returns a custom 404, so let's point to a link that
works today instead.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
This migrates the plaintext README in
board/theobroma-systems/ringneck_px30 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Only setup_boottargets differs from the original misc_init_r from
Rockchip mach code, so let's use rockchip_early_misc_init_r instead of
reimplementing the whole misc_init_r from Rockchip.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Ringneck PX30 and Puma RK3399 both have the same expectation with regard
to bootstd device order and U-Boot environment storage device, except
that Puma RK3399 also supports SPI Flash.
Let's move all of this into a common file where common logic can be put.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prepare to put the similar logic around storage medium selection for
Ringneck PX30 and Puma RK3399 in common, let's not use hardcoded paths
but use uclass functions instead to find udevice based on their DT node
full path.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It's happened that glitches on the STM32_RST and STM32_BOOT lines have
put the STM32 companion microcontroller into DFU mode making it not boot
its FW, rendering it useless for the user.
Considering that the STM32 companion microcontroller is always reset on
a reboot or power cycle, resetting it once again in U-Boot SPL isn't
going to hurt it any more.
For ATtiny companion microcontroller, the situation is a bit different
because a reboot or power cycle doesn't reset it. Additionally, since it
can only be reset with a UPDI reset on the STM32_RST line, and that is
virtually impossible to mistakenly trigger, the ATtiny is unlikely to be
in unwanted reset or enter reset because U-Boot toggles STM32_RST line.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Ringneck PX30 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
