As there are few redundant functions in board/ti/*/evm.c files, pull
them to a common location of access to reuse and include the common file
to access the functions.
Call k3-ddrss driver through fixup_ddr_driver_for_ecc() to fixup the
device tree and resize the available amount of DDR, if ECC is enabled.
Otherwise, fixup the device tree using the regular
fdt_fixup_memory_banks().
Also call dram_init_banksize() after every call to
fixup_ddr_driver_for_ecc() is made so that gd->bd is populated
correctly.
Ensure that fixup_ddr_driver_for_ecc() is agnostic to the number of DDR
controllers present.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Update simple-framebuffer device-tree node by enumerating framebuffer
related information in existing simple-framebuffer node in Linux
device-tree file and enabling it.
In case there is no simple-framebuffer stub detected in Linux kernel
device-tree and video is still active, then update the device-tree to
reserve the framebuffer region for the active splash screen.
This helps preserve the splash screen till the display server takes over
after OS is booted.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62x
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Stop using the findfdt script and switch to setting the fdtfile from
C code.
While at this, replace findfdt in environment with a warning as it is
no longer needed
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Remove video_setup from evm_init sequence since video memory is getting
called at an earlier place to make sure video memory is reserved at
the end of RAM.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use spl_dcache_enable, in place of setup_dram, arch_reserve_mmu to set
up pagetable, initialise DRAM and enable Dcache to avoid multiple
function calls.
Check for CONFIG_SPL_VIDEO in place of CONFIG_SPL_VIDEO_TIDSS to prevent
any build failure in case video config is not defined and video related
functions are called.
Check for CONFIG_SPL_SPLASH_SCREEN and CONFIG_SPL_BMP before calling
splash_display to avoid compilation failure.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
At the time of compilation evm.c gives below warning for implicit
declaration of enable_caches, to mitigate this include cpu_func.h.
board/ti/am62x/evm.c: In function ‘spl_board_init’:
board/ti/am62x/evm.c:90:9: warning: implicit declaration of function ‘enable_caches’ [-Wimplicit-function-declaration]
90 | enable_caches();
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
To enable splash screen on AM62x at a53 SPL setup DRAM, set page table,
enable cache to allow copying of bmp image to frame buffer and display
it using splash_display.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Add ospi boot media support to load splash image from OSPI memory,
add offset to read image from ospi and necessary flags defininig type
of storage and storage device.
Use CONFIG_IS_ENBALED to use the splash locations at SPL and u-boot
proper.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Splash screen function needs splash source information
to load image and display it, splash_location provides
the necessary info, Set default_splash_location to MMC
at partition 1:1. Probe DSS for splash screen display.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Call into k3-ddrss driver to fixup device tree and resize
the available amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup
as done from R5 SPL and apply it to DT passed to A53 U-boot,
which in turn passes this to the OS.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the appropriate fdtdec_setup_mem_size_base() call in
dram_init() and fdtdec_setup_bank_size() in dram_bank_init()
to pull these values from DT, where they are already available,
instead of hardcoding them.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
