This updates the "old style" DTs to that of Linux v6.10, matching what
OF_UPSTREAM is at now. Hopefully we won't need to do this (manually)
anymore. Since this brings in the DT for a new board (Tanix TX1), also
add the defconfig for that, which has just been waiting for that sync.
There are three more fixes: two for the SPI clock setup, which avoids
too high frequencies in some cases, and one fix to avoid a build warning
with GCC 14 for the sunxi TOC0 part of the mkimage tool.
The gitlab CI passed, and I tested the SPI flash on the OrangePi Zero 3
and also booted that into Linux.
The Tanix TX1 is a tiny TV box, featuring the Allwinner H313 SoC with up
to 2GB of DRAM and 16GB of eMMC. There is no SD card or Ethernet port on
this small device, but it can be booted via the USB debug "FEL" mode.
The bootloader could then be written to the eMMC.
Add the defconfig for that board, and add the devicetree file to the
Makefile, for it to be built.
The DRAM parameters were taken from the vendor firmware on the eMMC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Versal NET boards has QSPI and OSPI and default bus set to 0
is not working when system is booting out of OSPI which is
controller 1, as fixed aliases are set for all the boards
i.e., QSPI to 0 and OSPI to 1. Add controller autodetection
via spi_get_env_dev().
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240614124811.22945-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
LDFW is a Loadable Firmware which provides additional security
capabilities in EL3 monitor. For example, True Random Number Generator
(TRNG) block registers can't be accessed from EL1 (where U-Boot and
Linux kernel are running), but it's possible to access TRNG capabilities
via corresponding SMC calls, which in turn are handled by LDFW. To do
so, LDFW firmware has to be loaded first. It's stored on a raw eMMC
partition, so it has to be read into NWD (Normal World) RAM buffer, and
then loaded to SWD (Secure World) memory using the special SMC call to
EL3 monitor program. EL3_MON will load LDFW to SWD memory, more
specifically to the area starting at 0xbf700000 (with size of 7.5 MiB).
That memory area is reserved in device tree, so there shouldn't be any
collisions. After that LDFW becomes functional.
Implement LDFW firmware loading on board init. While at it, fix the
copyright date in header comments, as this board support was actually
added in 2024, not in 2020: it was probably a copy-paste mistake.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add an environment file for E850-96 board with default eMMC partition
list. It follows the Samsung's partition list used for Android-Q on
Exynos850 devices. It was verified on E850-96 board with:
=> gpt verify mmc 0 "$partitions"
Verify GPT: success!
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The conversion to DM_I2C is mandatory, rework to remove
use of legacy I2C API.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_I2C by the deadline.
Remove it.
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21728
- Conversions to DM_I2C and DM_SERIAL.
- Support for I2C3 and PWM1 for the imx6q clock driver.
- Improvements for udoo-neo
- Describe the i.MX93 CPU clocks in the devicetree to fix CPU clock printing
- Fix for SPI and NANC clk-imx8mn clock driver
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Rework to remove use of legacy I2C API. Also switch
to DM_SERIAL to avoid board removal warning.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
The udoo_neo_defconfig target supports several board variants.
All of these variants use the imx6sx-udoo-neo-basic devicetree in U-Boot.
Currently, the devicetree model as well as the board variant name
are shown:
...
Model: UDOO Neo Basic
Board: UDOO Neo FULL
...
Printing the devicetree model that is used internally by U-Boot
may confuse users.
Unselect the CONFIG_DISPLAY_BOARDINFO option and move the board printing
inside board_init() so that only the real board name that is detected
in run-time is printed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
With the watchdog driver model in place, it is no longer needed
to have board code to initialize the watchdog, so remove
its related board code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Daniel Schultz <d.schultz@phytec.de> says:
The overlays are specified in the bootenv.txt file that is loaded into
the environment. Then these overlays get loaded and applied via a script.
These scripts for loading and applying devicetree overlays are identical
for many phytec boards.
Create a common overlays.env that can be included.
Add support for devicetree overlays to phycore-imx8mp and include the
overlays.env for phycore-imx93.
Rename existing environment variables according to bootstd doc.
Move MMC boot logic into a common k3_mmc.env file and include the new
overlays.env file as well.
Use our common environment file to implement MMC boot.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Rename existing environment variables according to the bootstd doc.
Renamed variables are fdto_addr, bootenv_addr, fdt_addr and
fdt_file.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Include the common overlays env file for phycore_imx93.
The common overlays env file supports disabling loading overlays by
setting the no_overlays variable.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Add support for loading bootenv.txt as well as loading and applying
overlays during boot from mmc and net.
${no_bootenv}: Prevent loading external bootenv.txt environment. Use
${overlays} variable directly from u-boot environment.
${no_overlay}: Do not load overlays defined in ${overlays} variable.
Overlays loaded over the extension command are still
being applied.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
