Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Enable MMC_SPEED_MODE_SET config option in defconfig to enable
changing MMC bus modes with mmc rescan for am62ax device.
Signed-off-by: Judith Mendez <jm@ti.com>
Prasanth Babu Mantena <p-mantena@ti.com> says:
The channel allocation and deallocation for dma copy was happening on every
dma transfer. This is a overhead for transactions like NAND, which does
page reads recursively for complete data.
So, moving the dma allocation to probe and implement corresponding
remove function and cleanup dma device while exiting from spl.
Enable SPL_DM_DEVICE_REMOVE, for device removal capability in SPL.
Link: https://lore.kernel.org/r/20241009145703.1970034-1-p-mantena@ti.com
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable OF_UPSTREAM for am62a7-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
There is a default ATF load address that is used for devices that have
ATF running in SRAM. For AM62 and AM62a, ATF runs from DRAM. Instead
of having to override the address in every defconfig, make add a
default for these ATF in DRAM devices.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Stop using the findfdt script and switch to setting the fdtfile from
C code.
While at this, replace findfdt in environment with a warning as it is
no longer needed
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
All K3 boards now are secure by default, instead of setting this in each
defconfig, make it implied by the ARCH config.
The only exception is IOT2050, which I do not believe will have any
problems with being a TI_SECURE_DEVICE, but for now turn it off to keep
its config the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Default to common bootcmd that is set across all k3 devices.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
This is required for UART boot flow where u-boot.img needs to be
downloaded via YMODEM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
TI's security enforcing SoCs will authenticate each binary it loads by
comparing it's signature with keys etched into the SoC during the boot
up process. The am62ax family of SoCs by default will have some level of
security enforcement checking. To keep things as simple as possible,
enable the CONFIG_TI_SECURE_DEVICE options by default so all levels of
secure SoCs will work out of the box
Enable the CONFIG_TI_SECURE_DEVICE by default
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
We're currently using CONFIG_BOOTCOMMAND to run custom boot scripts to
jump into linux. While this works, let's begin the transition to more
distribution friendly jumps to linux by enabling distro_bootcmd.
Convert the custom bootcmd to a distro_bootcmd
Signed-off-by: Judith Mendez <jm@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce the minimum configs, only SD-MMC and UART boot related
settings, to serve as a good starting point for the am62a as we add more
functionality.
Signed-off-by: Bryan Brattlof <bb@ti.com>
[trini: Disable CONFIG_NET as it's not used, in both platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
