After the full convertion of usb gadget interrupt handling to
usb_gadget_generic_ops, it is now possible to use DM_USB_GADGET,
DWC2_OTG and DWC3_GENERIC together without causing a build error.
Change to use USB_DWC3_GENERIC instead of USB_XHCI_DWC3 to complte the
migration initiated in commit 1bc4e8eb1d7f ("rockchip: Migrate to use
DM_USB_GADGET on RK3328"). No functional change is intended.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3328 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate all RK3328 boards to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB gadget is not working fully as expected on RK3328, it uses a
board_usb_init() function to initialize the DWC2 OTG port.
The board_usb_init() function does not intgrate with the generic phy
framework and as a result the USB phy is not properly configured before
or after USB gadget use.
Having both USB_DWC2 and DWC2_OTG enabled for the same board is also
causing some issues.
Trying to use rockusb or ums command after usb stop result in a freeze
due to usb stop is putting the phy in a suspended state.
=> usb start
=> usb stop
=> ums 0 mmc 0
--> freeze due to usb phy is suspended <--
Fix this by only using one of USB_DWC2 (host) or DWC2_OTG (peripheral)
depending on the most likely usage of the otg port and by migrating to
use DM_USB_GADGET instead of a board_usb_init() function.
The nanopi-r2 and orangepi-r1-plus variants share OTG and power using a
Type-C connector, mark these boards dr_mode as peripheral, the most
likely usage is for recovery and image download.
The rock64 and roc-cc currently use dr_mode as host, remove the DWC2_OTG
driver from these boards to ensure that the USB_DWC2 driver is used.
The rock-pi-e board does not enable the usb20_otg node so both USB_DWC2
and DWC2_OTG is removed from this board.
Enable RockUSB and UMS on all boards with a otg port in peripheral mode.
Also with the migration to DM_USB_GADGET completed the U-Boot specific
change to reorder usb nodes in the soc device tree can be reverted.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the stack and text base used by U-Boot SPL and proper on RK3328
there is a high likelihood of overlapping when U-Boot proper + FDT nears
or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3328:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ 2M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[ -8K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ -8K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[ 32M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [2M, 4M-8K) with this layout.
However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is
restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to
fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Kconfig options to enable support for booting from SPI NOR flash on
Orange Pi R1 Plus boards.
The generated bootable u-boot-rockchip-spi.bin can be written to 0x0 of
SPI NOR flash. The FIT image is loaded from 0x60000, same as on RK35xx
boards.
=> sf probe
SF: Detected zb25vq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1376768 bytes read in 66 ms (19.9 MiB/s)
=> sf update ${fileaddr} 0 ${filesize}
device 0 offset 0x0, size 0x150200
1126912 bytes written, 249856 bytes skipped in 14.22s, speed 100542 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers
and change to use the dwc3-generic driver on remaining RK3328 and RK3399
boards.
MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to
enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along
with the default y of USB_XHCI_DWC3_OF_SIMPLE.
There is no intended change in functionality with this changes, USB 3.0
is expected to continue same as before this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
