Enable all the necessary options for capsule updates to work, as well as
a few additional EFI features.
Capsule updates themselves are only enabled for the RB3 Gen 2, since the
exact details on where to flash U-Boot (or how to handle multiple boot
methods) has not been finalised for other boards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now the Qualcomm controller and PHY drivers were accepted,
enable then in the qcom_defconfig file.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
The SM8550 and SM8650 SoCs requires PINCONF to properly
setup SDC pins in order to function correctly.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable clk and pinctrl for sm8150
Signed-off-by: Julius Lehmann <lehmanju@devpi.de>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Some newer boards end up with a bunch of holes in the memory map due to
how Qualcomm's hypervisor and ABL work. The end result is 14+ memory
regions.
Bump CONFIG_NR_DRAM_BANKS to 24 so we can handle these and any future
expansion easily.
Yes, this is ridiculous, but there is no other way.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The LMB memory maps are now being maintained through a couple of
alloced lists, one for the available(added) memory, and one for the
used memory. These lists are not static arrays but can be extended at
runtime. Remove the config symbols which were being used to define the
size of these lists with the earlier implementation of static arrays.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Make use of CONFIG_DEFAULT_ENV_FILE and move the default qcom
environment to a file under board/qualcomm.
This is much cleaner and means we don't need to recompile on changing
the environment.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable the clock/pinctrl drivers for these two SoCs. Previously left out
due to only being used on the db410c and db820c respectively which both
have their own board code. We can still boot these with most features
working without that board code.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sam Day <me@samcday.com>
EFI initialisation fails without this, and with proper SMBIOS v3 support
in (and automatic generation of useful tables) there's no reason for us
not to do this on qcom platforms.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Defining this as 0 results in bootm causing a null pointer exception...
Define it at a safe default which is valid RAM on most qcom boards.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Give us lots of room for the appended FDT.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Switch to using upstream DT from dts/upstream.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable the clock and pinctrl drivers for qcm2290, sm6115, and sm8250.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable support for the DWC3 USB controller and required dependencies for
Qualcomm boards, specifically the DB845c:
* IOMMU / SMMU
* USB high-speed PHYs
* Mass storage and ACM gadgets
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm FDTs are on the larger size, and with the addition of DT
modifications during board_init() it makes sense to enable OF_LIVE
globally. The cost of building the tree should be offset by the
increased efficiency at which we can walk it.
Some rough measurements with CONFIG_BOOTSTAGE suggests that this might
add 0.1-0.2ms to the boot-to-console time. However the reset-to-reset
timer difference is in the range of 0.5ms so this could just be noise.
Suffice to say, no significant slow down.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
QCS404 supports Synopsys Designware Ethernet QOS IP and we already have
the corresponding glue layer present upstream as:
drivers/net/dwc_eth_qos_qcom.c. So enable corresponding support.
Along with that it is possible for Qualcomm platforms to retrieve MAC
address from I2C eeprom present on board. So enable corresponding
support as well.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import sdm845.dtsi from upstream, as well as the upstream DTS files for
the db845c and Samsung starqltechn. Delete the old board files.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Historically, Qualcomm boards have relied on heavy hardcoding in U-Boot,
in many cases to the specific SoC but also to the board itself (e.g.
memory map). This has been largely resolved by modernising the Qualcomm
drivers in U-Boot, however the board code still largely follows this
model.
This patch removes the board specific memory maps and duplicated board
init code, replacing it with generic init code.
The memory map is now built at runtime based on data read from DT, this
allows for the memory map to be provided without having to recompile
U-Boot. Support is also added for booting with appended DTBs, so that
the first-stage bootloader can populate the memory map for us.
The sdm845 specific init code is dropped entirely, it set an environment
variable depending on if a button was pressed, but this variable wasn't
used in U-Boot, and could be written to use the button command instead.
The KASLR detection is also dropped as with appended dtb, the kaslr seed
can be read directly from the DTB passed to U-Boot.
A new qcom_defconfig is added, with the aim of providing a generic
U-Boot configuration that will work on as many Qualcomm boards as
possible. It replaces the defconfig files for the Dragonboard 845c,
Galaxy S9, and QCS404 EVB. For now the db410c and 820c are excluded as
they still have some board code left.
Similarly, the config headers for db845c, starqltechn, and qcs404-evb
are replaced by a single qcom header.
The previously db410c-specific board_usb_init() function is made to be
generic and is added to mach-snapdragon. While we lack proper modelling
for USB configuration, using a well-known named pinctrl state is a
reasonably generic middleground, and works using upstream DT. This
function will do nothing unless the USB node has a pinctrl state named
"device", in which case it will be set when entering USB peripheral
mode.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
