Migrate RK3588 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is not migrated to use OF_UPSTREAM:
- generic-rk3588: Generic target only meant for U-Boot use
- toybrick-rk3588: Merged in v6.9-rc1
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the quartzpro64-rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3588 boards do not have any pwm-regulator compatible nodes in DT, drop
the superfluous REGULATOR_PWM Kconfig options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the following memory layout is typically used on RK3588:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ 3.5M, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[ 10M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[11.5M, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 11.5M) with this layout.
However, on ROCK 5A the SPL stacks is overlapping:
[ -X, 16M) - SPL pre-reloc stack (SPL_STACK)
[15.5M, 16M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 16M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 15M, 16M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
Because bind and probe udevice instanses is allocated on the pre-reloc
malloc heap, there is going to be an overlap when reloc malloc heap
reaches close to 512 KiB of usage.
Migrate to use common bss, stack and malloc heap size and addresses to
mitigate these limitations and allow for a larger U-Boot proper size.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Update for new boards defconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable Kconfig options to support AHCI, PCI and USB features. This help
keep rk3588-quartzpro64 in sync with other RK3588 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Writing to eMMC using HS200 mode work more reliably then other modes on
RK3588 boards.
Enable MMC_HS200_SUPPORT Kconfig option to prefer use of HS200 mode.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Weizhao Ouyang <o451686892@gmail.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
