Enable the IO domain on Ringneck. Based on the current HW design, this
should do nothing else than making sure vccio6 iodomain is controlled by
the GRF and not GPIO0B6.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enables FIT verification in SPL for its payload (bl31, u-boot.itb,
...). This makes PX30 Ringneck match what happens on other Theobroma
boards.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB gadget simply doesn't work right now on PX30. Tested on PX30 EVB and
PX30 Ringneck with Linux mainline and Rockchip 5.10 Linux as well as
U-Boot.
We don't want to our users to assume that USB gadget is supported on Q7
USB P1 on Ringneck Haikou, so let's remove its support, which also
removes the ums CLI command, fastboot and Android image booting
support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
RK3588 Jaguar and Tiger, and RK3399 Puma use standard boot with the full
feature set, so let's do that as well for PX30 Ringneck.
Disable support for unused OSes as Linux is the primary target.
Enable a bunch of commands:
- boot/bootd
- erofs
- gpio
- iminfo
- imxtract
- itest
- pmic
- regulator
- sleep
- squashfs
that could be useful and are also found in Jaguar and Tiger defconfigs.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ringneck was mistakenly set to allow up to 128KiB for the TPL code size
while PX30 SoC only has 16KiB of SRAM.
Therefore, let's use the default value of TPL_MAX_SIZE from the SoC
(which is 10KiB) so that the max code size is actually checked and
useful.
Fixes: c925be73a0a8 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
On px30-ringneck the FIT payload is located at sector 0x200 compared to
the more Rockchip common sector 0x4000 offset:
SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
Because FIT payload is located at sector 0x200 and the TPL+SPL is
located at sector 64, the combined size of TPL+SPL cannot take up more
than 224KiB:
(0x200 - 64) x 512 = 0x38000 (224 KiB)
Adjust SPL_PAD_TO to match the used 0x200 sector offset.
While at it, update the px30-ringneck-u-boot.dtsi to remove the now
unnecessary override of simple-bin:fit:offset since SPL_PAD_TO matches
with the current formula.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Migrate PX30/RK3326 boards that exists in Linux v6.8 to use OF_UPSTREAM.
firefly-px30 is not migrated to OF_UPSTREAM because there's no Device
Tree in the Linux kernel.
Differences between U-Boot's Odroid-Go2 and Linux's are now moved to the
-u-boot.dtsi, though I have a gut feeling that the existing cru
overrides aren't necessary (anymore?).
The U-Boot GPIO led-0 is on GPIO0_C1 but such is the pin of PWM3 which
is used for Linux's PWM led-2 so keep Linux's.
I also doubt vcc_cam is actually used, though the Odroid-Go2 Black
Edition uses this dcdc regulator for WiFi, so let's just move it to the
-u-boot.dtsi to play it safe.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
U-Boot proper pre-reloc is currently running out of memory and it is
thus impossible to boot into U-Boot CLI.
Fix this by migrating to the common bss and stack addresses for PX30,
which drastically increases the size of the pre-reloc allocation pool (8
times bigger now). The memory layout in SPL and U-Boot proper now
match the other SoCs' using ROCKCHIP_COMMON_STACK_ADDR.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This is the kind of setting that typically doesn't need to be changed
between boards based on the same SoC, so let's make it the default in
PX30 Kconfig so we don't have to care about it in the defconfig if we
don't want to.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Now that Ringneck requires some board-specific code (namely resetting
the MCU companion controller) to be run during SPL stage, let's enable
SPL_BOARD_INIT.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is a useful tool to check the presence of a device on a specific
i2c bus, so let's enable it.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
DEBUG_UART_SKIP_INIT feature is implemented only by s5p (DEBUG_UART_S5P)
and pl01x (DEBUG_UART_PL010 or DEBUG_UART_PL011) serial drivers, but all
ARCH_ROCKCHIP configs rely on default DEBUG_UART_NS16550. The ns16550
serial driver does not depends on DEBUG_UART_SKIP_INIT, so drop it from
rockchip configs.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of letting the compiler error out if CONFIG_ENV_IS_NOWHERE is
not selected by the user, let's just enforce it when the user builds for
Ringneck PX30 so that no check needs to be performed by the compiler and
the configuration is always valid.
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_RAM_PX30_DDR4 got renamed to CONFIG_RAM_ROCKCHIP_DDR4 in commit
26f92be07e2a ("ram: rockchip: Add common ddr type configs"). Since both
patchsets were merged unbeknownst to the other, the conflict wasn't
detected while testing each patchset individually and could only be
observed after a merge to master branch.
Fixes: c925be73a0a8 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
