Basically, Radxa's boards are intended to turn LEDs on at U-Boot.
enable gpio-leds driver and led command.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3399 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate RK3399 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following target is not migrated to use OF_UPSTREAM:
- nanopi-m4-2gb-rk3399: DDR3 variant of nanopi-m4-rk3399 (LPDDR3)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3399-rock-pi-4 related device tree from Linux kernel v6.8.
Add SPI flash related nodes and options to support boot from SPI flash.
Add AHCI=y, SCSI_AHCI=y, AHCI_PCI=y and SCSI=y to support SATA HAT.
Change to SPL_MAX_SIZE=0x40000, SPL can be up to 256 KiB.
Add ROCKCHIP_IODOMAIN=y to configure io-domain voltage.
Add PHY_REALTEK=y and DM_ETH_PHY=y to support ethernet PHY.
Remove SPL_TINY_MEMSET=y to use full memset in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3399 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 17 2024 - 22:54:45 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related sdhci, sdmmc and spi flash pinctrl nodes
with bootph props. Also move bootph for common nodes shared by all
boards to the SoC u-boot.dtsi.
eMMC, SD-Card and SPI flash nodes are also changed to only be tagged
with bootph props for SPL and U-Boot pre-reloc phases.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Imply OF_LIBFDT_OVERLAY Kconfig options to add device tree overlay
support on all RK3399 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Move ROCK Pi 4 specific board code from the shared evb_rk3399 target
into its own board target and update related defconfigs to use the new
TARGET_ROCKPI4_RK3399 option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
With the stack and text base used by U-Boot SPL and proper on RK3399
there is a high likelihood of overlapping when U-Boot proper + FDT nears
or exceeded 1 MiB in size.
Currently the following memory layout is typically used on RK3399:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ 2M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 3M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[ -16K, 3M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ -16K, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ 4M, +8K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
[ -X, 64M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 63M, 64M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
SPL can safely load U-Boot proper + FDT to [2M, 4M-16K) with this layout.
However, the stack at [-X, 3M) used during U-Boot proper pre-reloc is
restricting the safe size of U-Boot proper + FDT to be less than 1 MiB.
Migrate to use common bss, stack and malloc heap size and addresses to
fix this restriction and allow for a larger U-Boot proper image size.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Complete the transition away from xhci-dwc3 and dwc3-of-simple drivers
and change to use the dwc3-generic driver on remaining RK3328 and RK3399
boards.
MISC, USB_DWC3 and USB_DWC3_GENERIC is enabled on boards that used to
enable USB_XHCI_DWC3. USB_XHCI_DWC3 is dropped from updated boards along
with the default y of USB_XHCI_DWC3_OF_SIMPLE.
There is no intended change in functionality with this changes, USB 3.0
is expected to continue same as before this change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Long are gone the times TF-A couldn't handle the FDT passed by U-Boot.
Specifically, since commit e7b586987c0a ("rockchip: don't crash if we
get an FDT we can't parse") in TF-A, failure to parse the FDT will use
the fallback mechanism. This patch was merged in TF-A v2.4-rc0 from two
years ago.
New boards should likely have this option disabled or explicitly enable
it in their respective defconfig.
Because existing boards might depend on a TF-A version that predates
v2.4, let's just enable this option in all RK3399 defconfigs.
Maintainers of each board can decide for themselves if they would prefer
to disable this option and allow U-Boot to pass the DT to TF-A.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
