Change to use FIT and FIT_SIGNATURE when loading U-Boot proper in SPL to
allow checksum validation and fallback loading of FIT from a different
mmc device.
Checksum validation of FIT adds around 140 ms to boot time:
Before:
Mark Elapsed Stage
0 0 reset
13 13 TPL
6,957 6,944 end tpl
25,102 18,145 SPL
131,932 106,830 end phase
132,137 205 board_init_f
444,277 312,140 board_init_r
1,404,987 960,710 eth_common_init
1,519,110 114,123 eth_initialize
1,524,734 5,624 main_loop
1,525,452 718 cli_loop
After:
Mark Elapsed Stage
0 0 reset
13 13 TPL
6,957 6,944 end tpl
35,744 28,787 SPL
271,220 235,476 end phase
271,420 200 board_init_f
588,474 317,054 board_init_r
1,548,950 960,476 eth_common_init
1,663,105 114,155 eth_initialize
1,668,734 5,629 main_loop
1,669,417 683 cli_loop
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
Tinker Board use RTL8211E or RTL8211F Ethernet PHY, datasheet list an
initial 10ms delay and then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Before:
1,404,971 960,924 eth_common_init
2,438,830 1,033,859 eth_initialize
2,444,449 5,619 main_loop
2,445,153 704 cli_loop
After:
1,404,987 960,710 eth_common_init
1,519,110 114,123 eth_initialize
1,524,734 5,624 main_loop
1,525,452 718 cli_loop
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for ASUS Tinker Board and S variant in dts/upstream can
be used as-is by U-Boot, migrate board to OF_UPSTREAM.
The change to use DT from dts/upstream will include minor changes and
fixes related to leds and regulators.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the migration to use standard boot, storage media should
automatically be initialized in the order listed in boot_targets env.
Drop USE_PREBOOT to speed up boot with ~12 seconds when booting from
e.g. SD-card or eMMC.
Before:
3,048,599 2,056 main_loop
3,050,717 2,118 usb_start
15,070,499 12,019,782 cli_loop
After:
3,058,244 2,054 main_loop
3,063,260 5,016 cli_loop
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Current use of SILENT_CONSOLE hide valuable information when something
goes wrong during boot, drop this Kconfig option to allow user to see
e.g. from what media U-Boot proper is loaded from.
A second Model line is printed on console due to DISPLAY_BOARDINFO_LATE,
drop this Kconfig option to remove the second redundant line.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate to use common bss, stack and malloc heap size and addresses to
unify memory use in TPL, SPL and pre-reloc.
Ensure SYS_MALLOC_F_LEN and TPL variant stay at 0x2000 and is unaffected
on other boards not changed to use common malloc heap size.
ENV_OFFSET is using the default value of 0x3f8000 and is also dropped.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing Kconfig options used by the rk3288-tinker-s variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable MISC_INIT_R and ROCKCHIP_EFUSE to read cpuid from efuse and set
the cpuid# and serial# env vars.
Change to read mac address from eeprom in rockchip_early_misc_init_r()
to ensure the ethaddr env var is set before rockchip_setup_macaddr() try
to set ethaddr based on cpuid.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The sdmmc power come from vcc33_sd pmic regulator and not from the
vcc_sd fixed regulator, as currently defined in the in-tree DT.
Drop vcc_sd and the related gpio7 and sdmmc_pwr nodes from being
included in SPL along with any related Kconfig option. Also enable
SPL_DM_SEQ_ALIAS to ensure aliases is handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
Video out on RK3288 boards has been broken since from few
releases due to the adding of reset support on vop but
missed enabling DM_RESET on associated boards.
This patch fixes those RK3288 boards.
Cc: Simon Glass <sjg@chromium.org>
Cc: Lin Huang <hl@rock-chips.com>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Fixes: <9749d2ea29e1> ("rockchip: video: vop: Add reset support")
Reported-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3288, RK3399 are now support cpu-info, so enable
DISPLAY_CPUINFO by default.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
