The device tree for Rockchip Toybrick TB-RK3588X has been merged into
dts/upstream with devicetree-rebasing v6.10-dts, migrate board to
OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RK3588 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is not migrated to use OF_UPSTREAM:
- generic-rk3588: Generic target only meant for U-Boot use
- toybrick-rk3588: Merged in v6.9-rc1
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3588-based devices now support creating DRAM banks with proper holes
by reading the ATAGS from Rockchip TPL blob, so let's use that mechanism
instead.
Since ft_board_setup isn't defined anymore, there's no need for
selecting CONFIG_OF_BOARD_SETUP.
Similarly, because the toybrick_rk3588.c would be empty, it is simply
removed, with the (would-be-empty) Makefile as well.
The CONFIG_NR_DRAM_BANK now defaults to 10 which is a safe bet for
reading banks from ATAGS, so let's use the default value instead.
Co-developed-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pinctrl must be configured for eMMC, SD-card and SPI flash to
successfully read FIT from all possible fallback media in SPL.
Include pinctrl props and enable the SPL_PINCTRL Kconfig option to
ensure FIT can be loaded from eMMC, SD-card and SPI flash.
Also enable the SPL_DM_SEQ_ALIAS Kconfig option to ensure that the
storage device sequence number matches in both SPL and U-Boot proper.
Fixes: 9fdd9a546986 ("board: rockchip: add Rockchip Toybrick TB-RK3588X board")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3588 boards do not have any pwm-regulator compatible nodes in DT, drop
the superfluous REGULATOR_PWM Kconfig options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the following memory layout is typically used on RK3588:
[ 0, 256K) - SPL binary
[ 256K, 2M) - TF-A / reserved
[ -X, 4M) - SPL pre-reloc stack (SPL_STACK)
[ 3.5M, 4M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 6M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 5M, 6M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
[ 10M, +X) - U-Boot proper binary (TEXT_BASE)
[ -X, 12M) - U-Boot proper pre-reloc stack (CUSTOM_SYS_INIT_SP_ADDR)
[11.5M, 12M) - pre-reloc malloc heap (SYS_MALLOC_F_LEN)
[ 64M, +16K) - SPL bss (SPL_BSS_START_ADDR, SPL_BSS_MAX_SIZE)
SPL can safely load U-Boot proper + FDT to [10M, 11.5M) with this layout.
However, on ROCK 5A the SPL stacks is overlapping:
[ -X, 16M) - SPL pre-reloc stack (SPL_STACK)
[15.5M, 16M) - pre-reloc malloc heap (SPL_SYS_MALLOC_F_LEN)
[ -X, 16M) - SPL reloc stack (SPL_STACK_R_ADDR)
[ 15M, 16M) - reloc malloc heap (SPL_STACK_R_MALLOC_SIMPLE_LEN)
Because bind and probe udevice instanses is allocated on the pre-reloc
malloc heap, there is going to be an overlap when reloc malloc heap
reaches close to 512 KiB of usage.
Migrate to use common bss, stack and malloc heap size and addresses to
mitigate these limitations and allow for a larger U-Boot proper size.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Update for new boards defconfig)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
