The zynqmp gem driver support max MTU size 1536, so remove tftp
block size 4096 from defconfig and use default tftp block size.
Fixes: a33b4b96b3cf ("xilinx: Enable MBEDTLS/LWIP/WGET and WGET_HTTPS")
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250304043030.2344536-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Added support for Infineon Octal flash components on the
Versal and Versal Net platforms.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250116051857.346921-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com> says:
This series adds support for Xilinx qspi parallel and
stacked memeories.
In parallel mode, the current implementation assumes that a maximum
of two flashes are connected. The QSPI controller splits the data
evenly between both the flashes so, both the flashes that are connected
in parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ
in sizes. So, except the sizes all other flash parameters of both the flashes
are identical.
Spi-nor will pass on the appropriate flash select flag to low level driver,
and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling the
address space each operation is performed at addr/2 flash offset, where addr
is the address specified by the user.
Similarly for read and erase operations it will read from both flashes, so
size and offset are divided by 2 and send to flash.
Enable the SPI_ADVANCE config option for all xilinx platforms, as
this is required for parallel-memories.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Enable setting speed mode using mmc dev commands.
The speed mode is provided as the last argument in these commands
(ex: mmc dev 0 0 10) and is indicated using the index from enum
bus_mode in include/mmc.h. A speed mode can be set if it is enabled
from device tree or from capabilities register
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240708091755.5021-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
It is good to be aware what information is shared via smbios interface
that's why enable it by default.
Signed-off-by: Michal Simek <michal.simek@amd.com>
ENV_OFFSET_REDUND config is by default set to 0 for flashes.
Saving the env variables is overwriting data at 0 offset,
which is wrong. So add default redund env offset
ENV_OFFSET_REDUND at 0x7F00000 for Versal NET platform.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240614125110.23058-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Boards which have for example MAC address in eeprom but not in Xilinx
format (legacy or FRU) could reference it via nvmem cells.
For example:
&gem0 {
nvmem-cells = <&mac>;
nvmem-cell-names = "mac-address";
};
&eeprom {
#address-cells = <1>;
#size-cells = <1>;
mac: mac-address@f0 {
reg = <0xf0 6>;
};
};
For getting it work above DT changes are required but also CONFIG_NVMEM
should be enabled. That's why enable it by default in generic defconfigs
to be able to use it directly by changing DT only.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9c8ee7a4c7a16367438a92a4c9581bac9d968f84.1712815454.git.michal.simek@amd.com
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZhaRdgAKCRDKSWXLKUoM
IS6LAKCdXJaEtlNLSC5IxeRJGmSTN4xPsACfdVL3mMzOZ1gw2+17uW1kHzzOgM4=
=vDHW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.07-rc1
xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding
zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant
zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update
mbv:
- Enable SPL and binman
- Small platform changes
zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path
versal-net:
- Support multiple locations for variables
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for versal-net platform as well.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240312113421.7394-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enabled the default utilization of the NFS command across all Xilinx
platforms to facilitate the booting of images through the network
using the NFS protocol.
Fixes: 10de12570799 ("disable NFS support by default")
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20240104045217.2966454-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit
widths of DMA. This significantly improves read and write throughput.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231027030446.4009-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data
structures at a random address at each boot.The bootloader
supports randomizing the virtual address at which the kernel image
is loaded. The bootloader must provide entropy by passing a random
u64 value in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831031658.2203-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for starting timer by setting up time stamp generator
registers. This is done only for EL3 i.e. mini U-Boot case.
For other cases, it will be done TF-A.
Add COUNTER_FREQUENCY and IOU_SWITCH_DIVISOR0 to Kconfig so that they
can be tuned as required.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fcd8b0dc4b45a11f5e753afff42f84738ac813da.1673336645.git.michal.simek@amd.com
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
