Set a size limit for this board so that we get a build error if it grows
too much.
Note that the limit is approximately, since it does not include the FDT,
microcode and fdtmap, which can change in size. However this board is
fairly stable, so overflowing this limit will likely result in the image
not fitting in the ROM space available for U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
This cannot be enabled early in boot since some other init is needed.
At this point it is unclear exactly what init is needed, so disable
the debug UART to avoid a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21310
- Enable SPL DTO application support for i.MX8MP DHCOM PDK2.
- Migrate imx8mn_bsh_smm_s2 and imx6ulz_bsh_smm_m2 to OF_UPSTREAM.
- Drop redundant imports with dts/upstream.
- Miscellaneous improvements for Gateworks i.MX8M boards.
Enable SPL DTO support to apply matching SoM specific DTOs to cater
for the SoM differences in DH i.MX8MP DHCOM PDK2 configuration. This
is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align
the two configurations.
Fixes: ad1158c50e0e ("arm64: dts: imx8mp: Switch to DT overlays for i.MX8MP DHCOM SoM")
Signed-off-by: Marek Vasut <marex@denx.de>
Migrate imx8mn_bsh_smm_s2 and imx8mn_bsh_smm_s2pro boards to OF_UPSTREAM.
Signed-off-by: Patrick Barsanti <patrick.barsanti@amarulasolutions.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
It is good to be aware what information is shared via smbios interface
that's why enable it by default.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable ICSSG driver, DP83869 phy driver, REMOTEPROC and PRU_REMOTEPROC
in am64x_evm_a53_defconfig. All these configs are needed for ICSSG
driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Jayesh Choudhary <j-choudhary@ti.com> says:
Hello there,
This series add the U-Boot support for our new platform of K3-SOC
family - J722S-EVM which is a superset of AM62P. It shares the same
memory map and thus the nodes are being reused from AM62P includes
instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
- Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
- Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
- 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
TRM: <https://www.ti.com/lit/zip/sprujb3>
Schematics: <https://www.ti.com/lit/zip/sprr495>
Boot test log:
<https://gist.github.com/Jayesh2000/0313e58fde377f877a9a8f1acc2579ef>
Introduce the initial configs needed to support the J722S SoC family.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
To better scale with the number of boards, separate TI K3 EFI capsule
configs into its own file that can be shared across TI K3 boards. This
will allow any platform level config changes to be done once.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Enable mtd command and remove SPI NOR flashes we do not
populate on our SoMs.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Enable configs required for booting via DFU.
Configs taken from the am62x_a53_usbdfu.config config fragment.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Update environment location to align with OSPI fixed-partition
definitions and provide a redundant environment at a 2nd location.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Update environment location to align with OSPI fixed-partition
definitions and provide a redundant environment at a 2nd location.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Copy fixed-partitions nodes from U-Boot device tree to OS device tree.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
The default value CYCLIC_MAX_CPU_TIME_US was 1000, which is
a little bit too low for slower hardware and sandbox.
On my MIPS Boston FPGA board with interaptiv CPU, wdt_cyclic
can easily take 3200 us to run.
On azure pipeline sandbox_clang, wdt_cyclic some times goes
beyond 1300 us.
Raise default value to 5000, which is the value already taken
by octeon_nic32. This is still sufficent to maintain system
responsiveness.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This stm32mp135f-dhcor-dhsbc board is a stack of DHCOR SoM based on
STM32MP135F SoC (900MHz / crypto capabilities) populated on DHSBC
carrier board.
The SoM contains the following peripherals:
- STPMIC (power delivery)
- 512MB DDR3L memory
- eMMC and SDIO WiFi module
The DHSBC carrier board contains the following peripherals:
- Two RGMII Ethernet ports
- USB-A Host port, USB-C peripheral port, USB-C power supply plug
- Expansion connector
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZnBfewAKCRDKSWXLKUoM
Ib/7AJ0cn3q7lMpxbSbRj33oftI8Vy8+owCeN35Nl8TN9l/DHbfusER4uVfnOVw=
=YMIB
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
ENV_OFFSET_REDUND config is by default set to 0 for flashes.
Saving the env variables is overwriting data at 0 offset,
which is wrong. So add default redund env offset
ENV_OFFSET_REDUND at 0x7F00000 for Versal NET platform.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240614125110.23058-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Boards which have for example MAC address in eeprom but not in Xilinx
format (legacy or FRU) could reference it via nvmem cells.
For example:
&gem0 {
nvmem-cells = <&mac>;
nvmem-cell-names = "mac-address";
};
&eeprom {
#address-cells = <1>;
#size-cells = <1>;
mac: mac-address@f0 {
reg = <0xf0 6>;
};
};
For getting it work above DT changes are required but also CONFIG_NVMEM
should be enabled. That's why enable it by default in generic defconfigs
to be able to use it directly by changing DT only.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9c8ee7a4c7a16367438a92a4c9581bac9d968f84.1712815454.git.michal.simek@amd.com
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
The am625-lp-sk is a variant of the am625-sk showcasing the low-power
features of the am625 SoC Family. Because it's essentially a board and
package spin of the am625-sk I've inherited the am625 configuration and
overridden what was needed.
This is a new spin of Nitin's original work which has been updated
significantly since October 2023
https://lore.kernel.org/u-boot/20231030110138.1347603-1-n-yadav@ti.com/
For those of us interested here is proof of life using buildroot:
https://paste.sr.ht/~bryanb/40f7787f7760bee383aa8fbc342a29e8544dbdab
This also works around a buildman issue not following #include
directives. To get around this I've redefined the variables it's looking
for inside the lp-sk defconfig to keep it happy for now. I made a pull
request on github and everything seems like it's happy
https://dev.azure.com/u-boot/u-boot/_build/results?buildId=8634&view=results
Nishanth Menon <nm@ti.com> says:
Cleanup am625 on by switching over the last two platforms (SK and
beagleplay) over to OF_UPSTREAM, and while at it, switch over am62a7
(last of the am62* family) over as well.
This superscedes the previous version of beagleplay only patch[1]
Test logs: https://gist.github.com/nmenon/ba310d3750a80789aca6a4fd90190135
The am62x-lp-sk is a package and reference board spin of the am62x-sk to
showcase the low-power features of the am62x SoC family. Because it so
closely resembles the am62x-sk board, use the preprocessor to inherit
its configuration making the needed changes for this board where
necessary.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Enable OF_UPSTREAM for am62a7-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Enable OF_UPSTREAM for am625-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
