Add support for K230 CanMV board with serial console and usb otg
support. It can boot via vendor's u-boot-spl and boot into Linux
via tftp through the onboard RTL8152.
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Reading doc/board/google/chromebook_coral.rst we can see that at some
point it was intended to put the bloblist in CAR, rather than DRAM, at
some point during development. This is fine for TPL/SPL stages where we
have very minimal information stored in the bloblist and so we can set
the limit there to 4KiB and then expand it to 196KiB in U-Boot proper so
there's room for ACPI tables and so forth. We also update the
documentation to use the same location for CONFIG_BLOBLIST_ADDR in both
references.
Signed-off-by: Tom Rini <trini@konsulko.com>
Raymond Mao <raymond.mao@linaro.org> says:
Motivations for changes:
Current SMBIOS library and command-line tool is not fully matching with
the requirements:
1. Missing support for other mandatory types (#7, #9, #16, #17, #19).
2. Only a few platforms support SMBIOS node from the device tree.
3. Values of some fields are hardcoded in the library other than fetching
from the device hardware.
4. Embedded data with dynamic length is not supported (E.g. Contained
Object Handles in Type #2 and Contained Elements in Type #3)
Changes:
1. Refactor the SMBIOS library and command-line tool to better align with
the SMBIOS spec.
2. Create an arch-specific driver for all aarch64-based platforms to fetch
SMBIOS private data from the device hardware (processor and cache).
3. Create a sysinfo driver to poppulate platform SMBIOS private data.
4. Add generic SMBIOS DTS file for arm64 platforms for those common strings
and values which cannot be retrieved from the system registers.
Vendors can create their own SMBIOS node using this as an example.
For those boards without SMBIOS nodes, this DTS file can be included to
have a generic SMBIOS information of the system.
5. Add support for Type #7 (Cache Information) and link its handles to
Type #4.
6. To minimize size-growth for those platforms which have not sufficient
ROM spaces or the platforms which don't need detailed SMBIOS
information, new added fields are only being built when kconfig
GENERATE_SMBIOS_TABLE_VERBOSE is selected.
Once this patch is acceptted, subsequent patch sets will add other missing
types (#9, #16, #17, #19).
Tests:
To test this with QEMU arm64, please follow the guide on dt_qemu.rst to
get a merged DT to run with.
```
qemu-system-aarch64 -machine virt -machine dumpdtb=qemu.dtb
cat <(dtc -I dtb qemu.dtb) <(dtc -I dtb ./dts/dt.dtb | grep -v /dts-v1/) \
| dtc - -o merged.dtb
qemu-system-aarch64 -machine virt -nographic -bios u-boot.bin \
-dtb merged.dtb
```
Link: https://lore.kernel.org/r/20241206225438.13866-1-raymond.mao@linaro.org
Enable sysinfo smbios by default for arm64.
When SYSINFO_SMBIOS is enabled, disable QFW_SMBIOS.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the SPI_STACKED_PARALLEL config option for
all AMD/xilinx platforms, as this is required for parallel and
stacked memories.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250103044812.18828-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add bootph props and enable related Kconfig options to include vital
regulators in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable use of SDMA mode when reading from eMMC to speed up boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With TPL being used to init DRAM, SPL being used to load FIT and the
adjusted FIT payload offset it is now possible to increase the size
limit of SPL to 256 KB and enable uses of dcache and FIT signature
validation.
Drop SPL_SYS_DCACHE_OFF=y to enable use of dcache in SPL.
Drop SPL_FIT_SIGNATURE=n to enable signature validation of FIT in SPL.
Change SPL_MAX_SIZE to 256 KB now that payload offset has moved in SPI
and TF-A may be loaded to 0x40000 in DRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate to use TPL, common bss, stack and malloc heap size and addresses
to unify memory use in TPL, SPL and pre-reloc with other RK3399 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Disable TPL_BLOBLIST)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The BootROM on RK3399 only read the first 2 KB of each 4 KB page from
SPI flash. With current FIT payload offset of 0x40000 this limits the
supported TPL+SPL size to only 128 KB.
Change to use 0xE0000 as FIT payload offset, similar to other RK3399
boards, to allow a maximum size for TPL of 192 KB and SPL of 256 KB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for rk3066a/rk3188 combined is now
available in the /dts/upstream directory.
Use imply OF_UPSTREAM to migrate all rk3066a/rk3188 boards.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa ROCK 5C[1] is a Rockchip RK3588S2 based single board computer.
[1] https://radxa.com/products/rock5/5c
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPi R3S(as "R3S") is an open source platform with dual-Gbps
Ethernet ports designed and developed by FriendlyElec for IoT
applications.
Specification:
- Rockchip RK3566
- 2GB LPDDR4X RAM
- optional 32GB eMMC module
- SD card slot
- 2x 1000 Base-T
- 3x LEDs (POWER, LAN, WAN)
- 2x Buttons (Reset, MaskROM)
- 1x USB 3.0 Port
- Type-C 5V 2A Power
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
After the migration to use standard boot, storage media should
automatically be initialized in the order listed in boot_targets env.
Drop USE_PREBOOT to speed up boot with ~12 seconds when booting from
e.g. SD-card or eMMC.
Before:
3,048,599 2,056 main_loop
3,050,717 2,118 usb_start
15,070,499 12,019,782 cli_loop
After:
3,058,244 2,054 main_loop
3,063,260 5,016 cli_loop
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Current use of SILENT_CONSOLE hide valuable information when something
goes wrong during boot, drop this Kconfig option to allow user to see
e.g. from what media U-Boot proper is loaded from.
A second Model line is printed on console due to DISPLAY_BOARDINFO_LATE,
drop this Kconfig option to remove the second redundant line.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use FIT and FIT_SIGNATURE when loading U-Boot proper in SPL to
allow checksum validation and fallback loading of FIT from a different
mmc device.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate to use common bss, stack and malloc heap size and addresses to
unify memory use in TPL, SPL and pre-reloc.
Ensure SYS_MALLOC_F_LEN and TPL variant stay at 0x2000 and is unaffected
on other boards not changed to use common malloc heap size.
ENV_OFFSET is using the default value of 0x3f8000 and is also dropped.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
Firefly-RK3288 use RTL8211 Ethernet PHY, datasheet list an initial 10ms
delay and then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing Kconfig options used by the rk3288-tinker-s variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for Firefly-RK3288 in dts/upstream can be used as-is by
U-Boot, migrate board to use OF_UPSTREAM.
Add chosen stdout-path prop to board u-boot.dtsi as it is missing in DT
from dts/upstream. Also change to use the upstream power_led symbol.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable MISC_INIT_R and ROCKCHIP_EFUSE to read cpuid from efuse and set
the cpuid# and serial# env vars.
Change to read mac address from eeprom in rockchip_early_misc_init_r()
to ensure the ethaddr env var is set before rockchip_setup_macaddr() try
to set ethaddr based on cpuid.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the migration to use standard boot, storage media devices should
automatically be initialized in the order listed in boot_targets env.
Drop USE_PREBOOT to speed up boot when booting from SD-card or eMMC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Current use of SILENT_CONSOLE hide valuable information when something
goes wrong during boot, drop this Kconfig option to allow user to see
e.g. from what media U-Boot proper is loaded from.
A second Model line is printed on console due to DISPLAY_BOARDINFO_LATE,
drop this Kconfig option to remove the second redundant line.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The sdmmc power come from vcc33_sd pmic regulator and not from the
vcc_sd fixed regulator, as currently defined in the in-tree DT.
Drop vcc_sd and the related gpio7 and sdmmc_pwr nodes from being
included in SPL along with any related Kconfig option. Also enable
SPL_DM_SEQ_ALIAS to ensure aliases is handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph props and enable related Kconfig options to include the sdmmc
regulator in SPL. Also enable SPL_DM_SEQ_ALIAS to ensure aliases is
handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph- props to emmc, sdmmc, uart and related pinctrl nodes to
ensure devices and pinctrl can be used in xPL and U-Boot pre-reloc.
Remove the explicit bootph-all prop from the pinctrl node, any bootph-
prop will automatically be propagated to the pinctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate to use common bss, stack and malloc heap size and addresses to
unify memory use in TPL, SPL and pre-reloc.
ENV_OFFSET is using the default value of 0x3f8000 and is also dropped.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable Kconfig options to read cpuid from efuse and set cpuid#, serial#
and ethaddr env vars based on the value read from efuse.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot timing and reporting (bootstage) infrastructure is useful for
performance analysis and debug but adds overhead and console noise when
using the device normally. Remove it from the device config.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Khadas Edge2 is a Rockchip RK3588S based SBC (Single Board Computer)
by Khadas.
There are tree variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MP4 GPU
3x MIPI CSI 4x lanes
2x MIPI-DSI DPHY 4x lanes
32/64GB eMMC
1x USB 2.0, 1x USB 3.0, 2x USB-Type-C
1x HDMI 2.1 output, 1x DP 1.4 output
USB PD over USB Type-C
Kernel commit:
04d552993522 ("arm64: dts: rockchip: Add Khadas edge2 board")
Signed-off-by: Jacobe Zang <jacobe.zang@wesion.com>
Change to use FIT and FIT_SIGNATURE when loading U-Boot proper in SPL to
allow checksum validation and fallback loading of FIT from a different
mmc device.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
MiQi use RTL8211 Ethernet PHY, datasheet list an initial 10ms delay and
then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for mqmaker MiQi in dts/upstream can be used as-is by
U-Boot, migrate board to OF_UPSTREAM.
The change to use DT from dts/upstream will include minor changes and
fixes related to work led and usb otg.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the migration to use standard boot, storage media devices should
automatically be initialized in the order listed in boot_targets env.
Drop USE_PREBOOT to speed up boot when booting from SD-card or eMMC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Current use of SILENT_CONSOLE hide valuable information when something
goes wrong during boot, drop this Kconfig option to allow user to see
e.g. from what media U-Boot proper is loaded from.
A second Model line is printed on console due to DISPLAY_BOARDINFO_LATE,
drop this Kconfig option to remove the second redundant line.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph props and enable related Kconfig options to include the sdmmc
regulator in SPL. Also enable SPL_DM_SEQ_ALIAS to ensure aliases is
handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
