This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add a new Kconfig symbol MDIO_TI_CPSW for the CPSW MDIO
driver and build it with proper DM support if enabled.
If MDIO_TI_CPSW is not enabled then we continue to
behave like before.
Clean up MDIO custom handling in am65-cpsw and use
dm_eth_phy_connect() to get the PHY.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW
NUSS). It has two ports and provides Ethernet packet communication for the
device and can be configured as an Ethernet switch. CPSW NUSS features: the
Reduced Gigabit Media Independent Interface (RGMII), Reduced Media
Independent Interface (RMII), and the Management Data Input/Output (MDIO)
interface for physical layer device (PHY) management. The TI AM65x SoC has
integrated two-port Gigabit Ethernet Switch subsystem into device MCU
domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII
and RMII interfaces and an internal Communications Port Programming
Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and on RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update TI Keystone 2 driver to re-use common mdio lib.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
All existing TI SoCs network HW have similar MDIO implementation, so
introduce common mdio support library which can be reused by TI networking
drivers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add drivers/net/ti/ folder and move all TI's code in this folder for better
maintenance.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
