The pin count wasn't updated when the special pins were added, as a
result it was never possible to configure the special pins on SM8250
boards.
Fix the pin count and allow the special pins to be configured. This
fixes sdcard support on the RB5.
Fixes: 58fa52042471 ("pinctr: qcom: sm8250: add special pins pins configuration data")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinmux bits for GPIO2-B0 to GPIO2-B6 actually have 2 bits width,
correct the bank flag for GPIO2-B. The pinmux bits for GPIO2-B7 is
recalculated so it remain unchanged. Add missing GPIO3-B1 to GPIO3-B7
pinmux data to rk3328_mux_recalced_data as mux register offset for these
pins does not follow rockchip convention.
This matches changes in following Linux commits:
- e8448a6c817c ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
- 5ef6914e0bf5 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins")
- 128f71fe014f ("pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pin detection on t20 depends on node name. With recent changes
in node naming, let's remove '_' to be safe about both '_' or
'-' use.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This patch add support to read register base address by name if
provided.
Also devfdt_get_addr_* is changed to dev_read_addr_* to support DT
live tree.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The reg-names in mt7988.dtsi have no _base suffix. Remove the suffix
will also make it match upstream linux format.
Fixes: 8c2cb748ef5 (pinctrl: mediatek: mt7988: rename reg-names to upstream linux format)
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Christian Marangi <ansuelsmth@gmail.com> says:
This is the last batch of part to push actual support of
OF_UPSTREAM for the mediatek SoC.
The plan is to make the current downstream DTS on part with
upstream implementation so we can permit a gradual transition to
it while we don't cause any regression to any user.
This is to have the same node downstream and upstream.
Mediatek is working hard upstream to also push all the remaining
nodes.
All patch are the final changes after the pinctrl patch
merged previously.
All patch pass CI tests
Link: https://github.com/u-boot/u-boot/pull/731
Link: https://lore.kernel.org/r/20250127134046.26345-1-ansuelsmth@gmail.com
Rename reg-names to upstream linux format. Upstream linux drop the
"_base". To make use of upstream DTSI, align to the upstream naming.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-by: Weijie Gao <weijie.gao@mediatek.com>
Use the driver macros so that the driver appears in the
linker list.
Reported-by: Simon Glass <sjg@chromium.org>
Fixes: 732f01aabf53 ("pinctrl: starfive: Add StarFive JH7110 driver")
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Weijie Gao <weijie.gao@mediatek.com> says:
This patch series add support for MediaTek MT7987 SoC with its reference
boards and related drivers.
This patch series add basic boot support on eMMC/SD/SPI-NOR/SPI-NAND for these
boards. The clock, pinctrl drivers and the SoC initializaton code are also
included.
Link: https://lore.kernel.org/r/cover.1737621362.git.weijie.gao@mediatek.com
Split MMIO accessors into pinctrl-imx-mmio.c and build this
file only if Kconfig symbol PINCTRL_IMX_MMIO is selected.
Select PINCTRL_IMX_MMIO Kconfig symbol for all but pinctrl-imx8.c
driver, which does not use the MMIO accessors. This reduces the
amount of code compiled on platforms which do not use the code.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
The only user of the SCU pinctrl code is pinctrl-imx8.c , fold
the entire pinctrl-scu.c code into pinctrl-imx8.c and remove the
matching Kconfig symbols and Makefile entries. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Call imx_pinctrl_set_state_common() from imx_pinctrl_scu_conf_pins(),
rename imx_pinctrl_scu_conf_pins() to imx_pinctrl_set_state_scu().
Get rid of the unnecessary ifdeffery in pinctrl-imx.h in the process.
Remove all SCU support from pinctrl-imx.c imx_pinctrl_set_state_mmio()
which makes that function a pure MMIO pinctrl configuration accessor.
Update pinctrl-imx8.c to call imx_pinctrl_set_state_scu directly.
No functional change.
This patch is best viewed with git show -w due to indent change.
Signed-off-by: Marek Vasut <marex@denx.de>
Split imx_pinctrl_set_state() into imx_pinctrl_set_state_common() and
imx_pinctrl_set_state_mmio(). The former does the common configuration
parsing, the later does call imx_pinctrl_set_state_common() and then
does pin configuration using either SCU or MMIO accesses. The SCU part
is going to be moved out in follow up patches.
This is a preparatory patch for follow up pinctrl drivers which
do not use the MMIO accessors, but some other means, like SCU or
otherwise. Those will call the common imx_pinctrl_set_state_common()
function wrapped into some other imx_pinctrl_set_state_*() function,
in a way similar to imx_pinctrl_set_state_mmio() does so for MMIO
accesses.
Update all imx_pinctrl_set_state_mmio() call sites to call
imx_pinctrl_set_state_mmio() instead.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
The current implementation of imx_pinctrl_remove() is specific
to the MMIO accessor implementation, rename the function to
imx_pinctrl_remove_mmio() to make this obvious. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Split imx_pinctrl_probe() into imx_pinctrl_probe_common() and
imx_pinctrl_probe_mmio(). The former does the common setup, the
later does the common setup and MMIO access configuration. The
common setup can be used as-is for SCU based systems, update
the pinctrl-imx8 to call only the common setup, update all the
other pinctrl drivers to call imx_pinctrl_probe_mmio().
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
The probe function is identical across all the pinctrl drivers.
Inline the imx_pinctrl_soc_info access into imx_pinctrl_probe()
and drop all the duplicate probe functions. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
The return callback for SCU variant of the pinctrl drivers does
nothing but returns 0. Remove the return callback from the SCU
driver itself, that has the same effect. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Rename the structure instances to match driver names, so they
can be easily looked up e.g. in objdump and readelf outputs.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Move imx_pinctrl_ops into drivers and staticize. This is preparatory
patch for follow up pinctrl drivers which will not use this variant
of imx_pinctrl_ops content. This should not change size, as most of
the deployments compiled in one pinctrl driver anyway. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
When converting to ofnode `ofnode_read_u32` was accedentally used to
replace `fdtdec_get_int` instead of `ofnode_read_u32_default`.
Use `ofnode_read_u32_default` to fix this.
Fixes: 59382d2 ("pinctrl: imx: Convert to use livetree API for fdt access")
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Use the IS_ENABLED() macro to reduce amount of #ifdef use in the driver
and improve code coverage. With IS_ENABLED() macro, the code is compiled
and then optimized out, which prevents bitrot.
In case no PFC table matches the SoC in use, do not probe the driver
and instead exit with -ENODEV. This should never happen under normal
conditions, because this would mean the driver DT compatible string
match happened, but the list in probe() cannot match the model listed
in match data associated with the compatible string on which the match
did happen.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- INTC/INTC-EX
- MSIOF
- PWM
- SSI
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- DU
- INTC-EX
- MSIOF
- PWM
- SSI
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- INTC-EX
- MSIOF
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- CAN/CANFD
- DU
- INTC-EX
- MSIOF
- PWM
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- DU
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- DU
- INTC/INTC-EX
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- CANFD
- DU
- INTC-EX
- MSIOF
- PWM
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- CANFD
- DU
- INTC-EX
- MSIOF
- PWM
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- DU
- INTC-EX
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- DU
- INTC-EX
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN/CANFD
- DU
- INTC-EX
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN
- DU
- INTC
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- CAN
- DU
- INTC
- MSIOF
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN
- DU
- INTC
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reduce the PFC tables by ifdeffing out pinmux settings which are
unlikely to be used by U-Boot. This helps reduce the size of the
bootloader in the 10 kiB range. This includes conditional build
of these PFC additions:
- Audio
- CAN
- DU
- INTC
- MSIOF
- PWM
- SSI
- VIN
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
By default the pin multiplexing tables used by U-Boot are reduced
to keep the size of the bootloader low. This option allows build of
full pin multiplexing tables the same way they are included in the
Linux kernel. This includes pin multiplexing options for Audio, CAN,
CANFD, DU, INTC, INTC-EX, MSIOF, PWM, SSI, for which there is no
U-Boot driver. This option is disabled by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In rzg2l_pinconf_set(), there are no new variables defined in the case
statement for PIN_CONFIG_INPUT_ENABLE so no additional scope is needed.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is be default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Ethenet interfaces on the Renesas RZ/G2L SoC family can operate at
multiple power supply voltages: 3.3V (default value), 2.5V and 1.8V.
rzg2l_pinconf_set() is extended to support the 2.5V setting, with a
check to ensure this is only used on Ethernet interfaces as it is not
supported on the SD & QSPI interfaces.
While we're modifying rzg2l_pinconf_set(), drop the unnecessary default
value for pwr_reg as it is set in every branch of the following if
condition.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
