Add the other LDOs that our rpmh driver can currently support. Some of
these are used on the RB5 to power the sdcard.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
As per TRM[0] Section 8.7.1 "TPS6594-Q1 Registers", LDOx_Vout
bit 6-1, define the NVM voltage settings.
Along side table 8-4 of above TRM, shows voltage to value mapping.
Driver wrongly using bits 5-1 to calculate voltage, and to convert
voltage to value driver was using buck's calculation.
So fix those calculation.
[0]: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Fixes: 5d7dbd22cf7d ("power: regulator: tps65941: use function callbacks for conversion ops")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Replace magic numbers in buckval2votl() & buckvolt2val() with macros to
help with clarity and correlate what the numbers correspond to in the
TPS65219 datasheet.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Replace printf() with pr_err() because pr_err() has a uniform print format
and takes into consideration the log levels supported.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To ease debugging, use dev_err() instead of dev_dbg() for
alerting when regulator has nonunique value.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Replace some debug() by dev_dbg() when dev variable
is available/valid.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Use PHASE_ as the symbol to select a particular XPL build. This means
that SPL_TPL_ is no-longer set.
Update the comment in bootstage to refer to this symbol, instead of
SPL_
Signed-off-by: Simon Glass <sjg@chromium.org>
Add PCA9452 PMIC/Regulator support.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The pmic could be trimed with updated BUCK1 range, so update the range
for trimed pmic. The default value of Toff_Deb is used to distinguish
the non-trimed and trimed pmic.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Both regulators_enable_boot_on/off() are unused and superseded by
regulator uclass regulator_post_probe(). Remove both functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Turn regulators_enable_boot_on() and regulators_enable_boot_off() into
empty functions. Implement matching functionality in regulator_post_probe()
instead. The regulator_post_probe() is called for all regulators after they
probe, and regulators that have regulator-always-on or regulator-boot-on DT
properties now always probe due to DM_FLAG_PROBE_AFTER_BIND being set on
such regulators in regulator_post_bind().
Finally, fold regulator_unset() functionality into regulator_autoset().
Signed-off-by: Marek Vasut <marex@denx.de>
In case a regulator DT node contains regulator-always-on or regulator-boot-on
property, make sure the regulator gets correctly configured by U-Boot on start
up. Unconditionally probe such regulator drivers. This is a preparatory patch
for introduction of .regulator_post_probe() which would trigger the regulator
configuration.
Parsing of regulator-always-on and regulator-boot-on DT property has been
moved to regulator_post_bind() as the information is required early, the
rest of the DT parsing has been kept in regulator_pre_probe() to avoid
slowing down the boot process.
Signed-off-by: Marek Vasut <marex@denx.de>
The buck variable is zero based, i.e. buck=0 match BUCK1 in datasheet.
Remove any buck + 1 calculation to be more consistent in usage of the
buck variable across the different RK8xx variants in the driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Wrong POWER_EN reg is used to get and set enabled state for the RK806
buck 4 and 8 regulators, also wrong POWER_SLP_EN0 bit is used for
suspend state for the RK806 buck 1-8 regulators.
Fix this by not adding one to the zero based buck variable.
Fixes: f172575d92cd ("power: rk8xx: add support for RK806")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
dev_get_driver_ops() may return NULL when the udevice is invalid.
Move the ops check to top of functions to consistently return -ENOSYS
when ops is unimplemented and prevent trying to access uclass plat data,
also add missing NULL checks to suspend ops.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
On some boards a PMIC regulator is flagged with regulator-on-in-suspend
and does not define any suspend or max microvolt, e.g. on Radxa ROCK 3A:
vcc_ddr: DCDC_REG3 {
regulator-name = "vcc_ddr";
regulator-always-on;
regulator-boot-on;
regulator-initial-mode = <0x2>;
regulator-state-mem {
regulator-on-in-suspend;
};
};
This result in suspend_uV having the value -ENODATA after probe.
This negative voltage, -ENODATA, gets missinterpreted and result in an
unexpected voltage being set by autoset.
E.g. on Radxa ROCK 3A the vcc_ddr regulator by default have a normal and
suspend voltage value of 0.5v. However, due to this missinterpretation
the suspend voltage end up beind set to 0.5625v instead.
Fix this by skip calling regulator_set_suspend_value() in autoset and
also protect calling set value ops when input value is -ENODATA.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Various improvements to Snapdragon support:
* Bumped up the pagetable size to handle newer SoCs with much more RAM
* Made memory map parsing more robust, fixing chainloading on
SM8550/SM8650
* Populate fdt_addr_r with U-Boot's FDT by default, and set $loadaddr to
prevent
crashes with some commands which expect it
* Added initial support for SC7280/QCM6490 and the new RB3 Gen 2 board
* Add debug config fragments to enable debug UART on some SoCs.
* Enable RPMh regulators on SM8550/SM8650
* Map the cmd-db memory explicitly since it may not be in the memory map
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/22255
Add the PM8550 & related regulators found on the SM8550 and SM8650 platforms.
The tables are imported from the Linux driver.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
For regulator-fixed-clock, the device's private data is never set so in
fixed_clock_regulator_set_enable() is null and the function cannot
complete successfully.
Rename the _plat structure to _priv to better represent its role and set
this as the private data. As shown by the set_enable() function and by
using the same .of_to_plat hook as regulator-fixed, the platform data is
regulator_common_plat so also set .plat_auto correctly.
Finally, set up the private data by adding a .probe function to look up
the clock and set the member variable.
Fixes: f3b5100aff3 ("regulator: fixed: add possibility to enable by clock")
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Kconfig and Makefile entries for this driver now that it can build
for U-Boot.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Refactor initialization to use U-Boot's driver model and API.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Port over the regulator ops to U-Boot's regulator API. Add back the
pmic5 mode map using U-Boot dm_regulator_mode API and adjust the
pmic5_pldo and pmic5_pldo_lv definitions. No functional changes.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Initially just include the few regulators needed for the RB5 board.
Others can be added back as-needed.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The X-Powers AXP717 is a PMIC with four buck converters and a number
of LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow
drivers to adjust voltages.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ryan Walklin <ryan@testtoast.com>
With a recent change, regulators_enable_boot_on() returns an error if a
regulator is already set. Check for and handle this situation.
Fixes: d99fb64a98a power: regulator: Only run autoset once for each regulator
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
My linter complains that the order isn't clear enough so let's put
parentheses around the ternary condition to make it happy.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-bob
For the sake of consistency, make all internal (starting with _)
functions expect a pmic udevice instead of a regulator udevice.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-bob
_ldo_get_suspend_value and _ldo_set_suspend_value get passed the parent
of the regulator (so the pmic) as first argument, therefore this udevice
should be used for pmic_* callbacks instead of using the parent of the
pmic.
To avoid further confusion, let's rename the argument to pmic instead of
dev, highlighting which kind of device we expect as argument.
Fixes: f047e4ab9762 ("regulator: rk8xx: add indirection level for some ldo callbacks")
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook-bob
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reuse TPS65941 regulator driver to adds support for
TPS65224 PMIC's regulators. 4 BUCKs and 3 LDOs, where
BUCK1 and BUCK2 can be configured in dual phase mode.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use function callbacks for volt2val, val2volt and slewrate lookups.
This makes it easier to add support for TPS65224 PMIC regulators.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Adds macros for buck and ldo ids and switched to using switch
case instead of if else in probe functions. Helps in adding
support for TPS65224 PMIC.
Signed-off-by: Bhargav Raviprakash <bhargav.r@ltts.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This adds support for RK806, only the SPI variant has been tested.
The communication "protocol" over SPI is the following:
- write three bytes:
- 1 byte: [0:3] length of the payload, [6] Enable CRC, [7] Write
- 1 byte: LSB register address
- 1 byte: MSB register address
- write/read length of payload
The CRC is always disabled for now.
The RK806 technically supports I2C as well, and this should be able to
support it without any change, but it wasn't tested.
The DT node name prefix for the buck converters has changed in the
Device Tree and is now dcdc-reg. The logic for buck converters is
however manageable within the current logic inside the rk8xx regulator
driver. The same cannot be said for the NLDO and PLDO.
Because pmic_bind_children() parses the DT nodes and extracts the LDO
index from the DT node name, NLDO and PLDO will have overlapping
indices. Therefore, we need a separate logic from the already-existing
ldo callbacks. Let's reuse as much as possible though.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
By passing a rk8xx_reg_info directly to the internal get_value, it'd be
possible to call this same function with a logic for getting the
rk8xx_reg_info different from the current get_ldo_reg, e.g. for NLDO and
PLDO support for RK806.
No logic change is expected.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
