Add manufacturing environment into STM32MP15xx DH electronics DHSOM
configuration. This environment is part of every board build, but only
takes effect on systems booted with the dh,stm32mp15xx-dhcor-testbench
device tree, i.e. systems populated with factory build of U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Make the dh_update_sd_to_sf script generic, rename it to dh_update_block_to_sf
and implement two specific dh_update_sd_to_sf and dh_update_emmc_to_sf scripts
which load U-Boot from either SD or eMMC and install it into SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In case CONSOLE_MUX and SYS_CONSOLE_IS_IN_ENV are enabled, the console
stdin, stdout, stderr must be defined in environment. Define the default
settings to fix the following warning on boot:
"
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
"
Sort the default environment as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add script which installs U-Boot binaries from SD card to eMMC
and makes the eMMC bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Align the script name with DH i.MX8MP DHCOM script name. Add
backward compatibility script to avoid breaking user scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a configuration file "stm32mp15_st_common.h" to handle the
STMicroelectronics boards configuration and rename stm32mp1.h to
"stm32mp15_common.h" to handle the generic STM32MP15x series configuration.
The configuration file "dh_stm32mp1.h" is also renamed to
"stm32mp15_dh_dhcom" for the configuration of board based on the
dhelectronics STM32MP15x SOM.
In the STMicroelectronics board configuration the default bootcmd
"bootcmd_stm32mp" is updated to only select the extlinux file found on
SD-Card on STM32MP15x EV1 for boot from NOR device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
