Import the headers needed for QCS404-evb.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the U-Boot specific dragonboard820c.dts file in favour of the
upstream apq8096-db820c.dts and an additional -u-boot.dtsi with the
U-Boot specific additions.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Don't use hardcoded clock IDs, use the IDs from the dt-bindings to be
compatible with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import PM8994 and PMI8994 DTSI files in preparation for switching
MSM8996 boards to upstream DTS.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import dt-binding headers for MSM8996/APQ8096 from Linux.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the U-Boot specific dragonboard410c.dts in favour of the upstream
msm8916-sbc.dts. No additional changes are needed to this DTS for U-Boot
support.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import the supporting pm8916.dtsi and msm8916-pm8916.dtsi files from
upstream in preparation for switching boards over.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import the dt-bindings headers in preparation for switching to upstream
DTS for MSM8916.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import sdm845.dtsi from upstream, as well as the upstream DTS files for
the db845c and Samsung starqltechn. Delete the old board files.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import the PM8998 and PMI8998 PMIC DTSI files from Linux as well
as the common audio codec in preperation for replacing board DTS files
with upstream.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Import the DT bindings headers that are used by SDM845 from Linux.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The MSM8916/APQ8016 Technical Reference Manual is publicly available and
contains a lot of useful register maps for many core parts of the SoC.
Include an archive.org link to it in the dragonboard410c documentation.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Replace the board specific docs with a generic board.rst file which
documents the build/boot process for the sdm845 and qcs404 boards now
that the only differences are the DTB in use.
At the same time, create a debugging page to document some useful
snippets and tips for working with Qualcomm platforms.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This board is entirely supported by the generic arch code and DTS. The
board code used to handle turning on the vbus regulator, however this is
now handled via DT.
With this, the board specific defconfig is also no longer needed, so
drop it as well.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
On Qualcomm platforms, the TZ may already have certain memory regions
under protection by the time U-Boot starts. There is a rare case on some
platforms where the prefetcher might speculatively access one of these
regions resulting in a board crash (TZ traps and then resets the board).
We shouldn't be accessing these regions from within U-Boot anyway, so
let's mark them all with PTE_TYPE_FAULT to prevent any speculative
access and correctly trap in EL1 rather than EL3.
Some lower level FDT functions are used here relying on some assumptions
about how Qualcomm devicetrees are laid out (#address/size-cells being 2
for reserved-memory), as this is the only way to make this acceptably
fast enough with dcache off. The full fat implementation takes 1800ms on
SDM845, the implementation in this patch takes <1.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
With just a few basic rules, we can generate the $fdtfile environment
variable to match the format used in Linux. This uses the root
compatible property inside u-boot, with specific handling for the
Dragonboard845c which is a special case, and for the qrb robotics
boards.
This is known to work on supported platforms, and lets us avoid having a
big lookup table.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Heavily inspired by Apple board code. Use the LMB allocator to configure
load addresses at runtime, and implement a lookup table for selecting a
devicetree.
As some Qualcomm RBx boards have different RAM capacities and base
addresses, it isn't possible to hardcode these regions.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Historically, Qualcomm boards have relied on heavy hardcoding in U-Boot,
in many cases to the specific SoC but also to the board itself (e.g.
memory map). This has been largely resolved by modernising the Qualcomm
drivers in U-Boot, however the board code still largely follows this
model.
This patch removes the board specific memory maps and duplicated board
init code, replacing it with generic init code.
The memory map is now built at runtime based on data read from DT, this
allows for the memory map to be provided without having to recompile
U-Boot. Support is also added for booting with appended DTBs, so that
the first-stage bootloader can populate the memory map for us.
The sdm845 specific init code is dropped entirely, it set an environment
variable depending on if a button was pressed, but this variable wasn't
used in U-Boot, and could be written to use the button command instead.
The KASLR detection is also dropped as with appended dtb, the kaslr seed
can be read directly from the DTB passed to U-Boot.
A new qcom_defconfig is added, with the aim of providing a generic
U-Boot configuration that will work on as many Qualcomm boards as
possible. It replaces the defconfig files for the Dragonboard 845c,
Galaxy S9, and QCS404 EVB. For now the db410c and 820c are excluded as
they still have some board code left.
Similarly, the config headers for db845c, starqltechn, and qcs404-evb
are replaced by a single qcom header.
The previously db410c-specific board_usb_init() function is made to be
generic and is added to mach-snapdragon. While we lack proper modelling
for USB configuration, using a well-known named pinctrl state is a
reasonably generic middleground, and works using upstream DT. This
function will do nothing unless the USB node has a pinctrl state named
"device", in which case it will be set when entering USB peripheral
mode.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
db820c predated support for prepending the kernel image header
automatically, drop it's custom linker script and head.S in favour of
this generic support.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Some of the db410c board support code was written to be generic and
placed in mach-snapdragon. However, as the db410c is the only board
using this, move the code out of mach-snapdragon. This makes is more
obvious what code is relevant for which targets and helps tidy things up
a little more.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the root compatible strings from upstream Linux, add missing
'#clock-cells' property to the gcc node.
Adjust some of the msm8916/apq8016 drivers to use the correct upstream
compatible properties and DT bindings.
This prepares us to switch to upstream DT in a future patch.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add a config fragment for building U-Boot such that it can be
chainloaded by aboot/LK rather than being flashed directly to the aboot
partition.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
On the DB410c we support running as a first stage bootloader. This
requires initialising the GPIOs which are muxed to UART before they can
be used. Add DM_FLAG_PRE_RELOC to the apq8016 pinctrl driver to ensure
that we do this early enough.
This is required to prevent the first few lines of UART log from being
dropped.
Reported-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Upstream devicetrees label GPIOs with "gpioX", not "GPIO_X", fix this
for SoCs where we're now using upstream DT.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Most platforms have a handful of "special" GPIOs, like the MMC
clock/data lanes, UFS reset, etc. These don't follow the usual naming
scheme of "gpioX" and also have unique capabilities and registers. We
can get away without supporting them all for now, but DT compatibility
is still an issue.
Add support for allowing these to be specified after the other pins, and
make all pinmux/pinconf calls for them nop.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust the DT to match upstream bindings.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Introduce a basic pinctrl driver for the SPMI PMIC GPIOs. This is
necessary to make proper use of upstream DT bindings specifically on the
dragonboard410c where they're used to switch between USB host and device
modes.
Only support for driving the pins as output low or high is enabled for
now.
To minimise duplicated code and allow for sharing common DT data, the
pinctrl driver is initialised as a child of the existing GPIO driver.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Some platforms hard reset when attempting to configure PMIC GPIOs. Add
support for quirks specified in match data with a single quirk to skip
this configuration. We rely on the GPIO already be configured correctly,
which is always the case for volume up (the only current user of these
GPIOs).
This is not expected behaviour but appears to be due to a U-Boot
specific bug. This quirk at least allows for the volume buttons to be
used on platforms where this bug is apparent.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the modern helpers to fetch the clock and use the correct property
("clocks" instead of "clock"). Drop the call to pinctrl_select_state()
as no boards have a "uart" pinctrl state and this prints confusing
errors.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Introduce support for early debugging. This relies on the previous stage
bootloader to initialise the UART clocks, when running with U-Boot as
the primary bootloader this feature doesn't work. It will require a way
to configure the clocks before the driver model is available.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
We should be returning the rate that we set the clock to, drivers like
MMC rely on this. So fix it.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Adjust the apq8016 and apq8096 drivers to use the upstream compatible
properties, and adjust the associated dts files in U-Boot.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The upstream DT is supported here, so drop the U-Boot specific binding
docs.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Use the clk_* helper functions and the correct property name for clocks.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add support for a vbus-supply regulator specified in devicetree. This
provides generic support to avoid hardcoded GPIO configuration in board
init code.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
When booting U-Boot on board with a locked down first-stage bootloader,
we emulate the Linux boot header. By passing the U-Boot FDT through this
first-stage bootloader and retrieving it afterwards we can pre-populate
the memory nodes and other info like the KASLR address.
Add a function to export the FDT addr so that boards can use it over the
built-in FDT.
Don't check is_addr_accessible() here because we might not yet have a
valid mem_map if it's going to be populated from the FDT, let the board
do their own validation instead.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org> #qcs404
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Refactor common QoS code into a new common header file, and the soc
specific setup_qos functions into a common API.
Rename $(soc)_qos_count and $(soc)_qos_data variables to qos_count and
qos_data. When QoS settings of more SoCs are added, only one pair will
be defined at a time, based on the config SOC_K3_$(soc).
This refactoring has been done for 2 major purposes.
- The auto-generated $(soc)_qos_data.c and $(soc)_qos.h files cannot
have any code that is specific to any bootloader. Those files have to
remain agnostic of different bootloader implementations and their
header files.
- The existing implementation was less than ideal and would have enabled
multiple $(soc)_qos_count and $(soc)_qos_data variables for all SoC
variants.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
The same U-Boot binary is compatible with multiple Verdin AM62 board
variants. However, some of the SoC models can only operate at a maximum
speed of 1 GHz.
Previously, the boards with lower-speed grades were running at
overclocked speeds, leading to kernel complaints about unsupported
configurations.
To resolve this issue, the operating speed has been decreased to the
maximum allowable value across all Verdin AM62 board variants. As a
result, there is a regression in overall boot time, increasing by around
200 milliseconds for the faster SoC variant.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Francesco Dolcini <francesco.dolcini@toradex.com> says:
This series fixes two regressions affecting multiple Toradex boards
(i.MX, TI and TEGRA based) and targets the current master, e.g. v2024.04
release.
U-Boot `reset` command is broken on all Tordex i.MX6* based SoMs since
v2023.07, this series fixes it enabling the `wdt-reboot` driver.
Since v2024.04-rc1 reading the Toradex configuration block is not working
properly anymore, the serial number and the hardware version are not read
correctly, preventing the board from functioning correctly (wrong mac address,
wrong DT, ...). This is fixed by reading the config block in `EVT_SETTINGS_R`
and adding a toradex sysinfo driver. In addition to that, we now use a random
mac address in case the config block is invalid.
Reported-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Closes: https://lore.kernel.org/all/CAKZ1LvM45MB8N0CqgU+C7i9=Bjb6kqNTxWo2Tv407HKLWtCMkA@mail.gmail.com/
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Closes: https://lore.kernel.org/all/e40ed93bd8f371ec56b8fc451dcb458f3ce6dcba.camel@toradex.com/
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Closes: https://lore.kernel.org/all/ZY2ZDWAQuTlRjV9H@francesco-nb/
commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()")
introduced a regression that 'reset' command unable to reset
imx6 and imx6ull based Toradex's modules in the u-boot.
This change enables a watchdog-based sysreset driver for
Toradex's colibri-imx6, colibri-imx6ull (with nand and emmc)
and apalis-imx6 which solves the reset command regression on
these modules.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixes: 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()")
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Set CONFIG_NET_RANDOM_ETHADDR=y, which sets random eth address in
case there is no toradex config block programmed.
In case of missing toradex config block the generated mac address was
always the same, linked to serial number 0.
Use random generated mac address instead.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit introduces support for the Toradex sysinfo driver in U-Boot,
which uses information from Toradex config block to print correct
board model.
In case the Toradex config block is not present sysinfo prints the model
of the board provided by device tree removing per board specific prints.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sysinfo prints the model obtained from device tree, checkboard()
take info from hardware and tdx_checkboard() use the model retrieved by
toradex config block.
Remove the print from checkboard() function because the model obtained
from toradex config block is the most complete.
If toradex config block is missing the model info from device tree is
enough.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Since checkboard() is used instead of show_board_info(), in case toradex
config block is missing or malformed, checkboard is recursively called.
It prints a long list of "MISSING TORADEX CONFIG BLOCK" till the stack
is full.
Fixes: edb0ecd18708 ("toradex: Use checkboard() instead of show_board_info()")
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin iMX8M Plus
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable SPL and binman to generate u-boot.img (machine mode) and u-boot.itb
(supervisor mode). DTB is placed at fixed address to ensure that it is 8
byte aligned which is not ensured when dtb is attached behind SPL binary
that's why SPL and U-Boot are taking DTB from the same address.
Also align addresses for both defconfigs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/85506bce5580d448f095f267d029e3932c5e9990.1707911544.git.michal.simek@amd.com
SPL is cleaning bss after calling board_init_f. Setting up console is done
and little_endian global variable is cleared which caused that console
stops to work. That's why move it to data seciton now. The patch should be
reverted when bss is cleared before board_init_f is called.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/934dc8871c59265eb9d8012193aa97d9b8bd7f33.1707911544.git.michal.simek@amd.com
