Add the vcc3v3-supply regulator and its link to the pcie controllers.
Tested-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240723195538.1133436-2-heiko@sntech.de
[ upstream commit: e0ec6d48226fb3d4df18895b56f0b7a94c0fe474 ]
(cherry picked from commit 59939b4343db08fa08098238160007e6ded72be9)
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 7576ab2facae ("riscv: Add support for AMD/Xilinx MicroBlaze V")
added support for 32bit version. 64bit version is also available that's why
wire it up too.
DT is providing description for generic QEMU target.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Align smode defconfig with upstream QEMU. It could be the part of commit
9d688e6da5c9 ("riscv: mbv: Align DT with QEMU").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
DTB should be also placed to DDR. It should be the part of commit
9d688e6da5c9 ("riscv: mbv: Align DT with QEMU").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To restore MMC boot, enable SPL_SYS_MMCSD_RAW_MODE and recover
SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Fixes: 2a00d73d081 ("spl: mmc: Try to clean up raw-mode options")
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable the clock gating bit of ccache when the platform has the ccache0.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Commit 136b7b6d2e98 ("Subtree merge tag 'v6.11-dts' of dts repo [1] into
dts/upstream") updates the upstream dts for E850-96 board, bringing
upstream TRNG node. There is no need to keep TRNG node in appended dts
anymore, so remove it.
Tested on E850-96 board by running 'rng' command in U-Boot shell.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
unsigned int count is used to capture return of dev_read_string_count.
When an error occurs dev_read_string_count returns -ve, which can
hence not be handled correctly. Use int instead of unsigned int so
that errors are detected.
Fixes: 16ca80adc551 ("pinctrl: Add pinctrl driver support for Exynos7420 SoC")
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When compiling for riscv64, a bunch of warning is produced for the file
drivers/bios_emulator/besys.c. This patch fixes a portion of those warnings,
caused by incorrect first argument to pci_{read,write}_config_* functions.
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
MTRR functionality is available only on x86, so this driver cannot be compiled
on other architectures. Fix this with preprocessor directives.
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
The bios_emulator driver cannot be compiled for RISC-V because the x86emu.h
header file doesn't define the comment symbol ("#") for the assembler.
With this patch, use the same symbol as for e.g. x86.
Signed-off-by: Yuri Zaporozhets <yuriz@qrv-systems.net>
Record the last active menu item and check if it equals to the
current selected item before reprint.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
This patch adds a new callback named need_reprint for menu.
The need_reprint will be called before printing the menu. If the
callback exists and returns FALSE, menu printing will be canceled.
This is very useful if the menu was not changed. It can save time
for serial-based menu to handle more input data.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
It's observed that the bootmenu on a serial console sometimes
incorrectly quitted with superfluous characters filled to command
line input:
> *** U-Boot Boot Menu ***
>
> 1. Startup system (Default)
> 2. Upgrade firmware
> 3. Upgrade ATF BL2
> 4. Upgrade ATF FIP
> 5. Load image
> 0. U-Boot console
>
>
> Press UP/DOWN to move, ENTER to select, ESC to quit
>MT7988> [B
Analysis shows it was caused by the wrong logic of bootmenu_loop:
At first the bootmenu_loop received the first ESC char correctly.
However, during the second call to bootmenu_loop, there's no data
in the UART Rx FIFO. Due to the low baudrate, the second char of
the down array key sequence hasn't be fully received.
But bootmenu_loop just did a mdelay(10), and then treated it as a
single ESC key press event. It didn't even try tstc() again after
the 10ms timeout.
This patch fixes this issue by letting bootmenu_loop check tstc()
twice.
Tested-By: E Shattow <lucent@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Leo Yan <leo.yan@arm.com> says:
This patch series is to refine the booting on Arm Total Compuate
platform.
It changes to use the info passed in DTB for initialization DRAM info,
and dynamically initializes the booting envoironment variables.
Another big change is to use an envoironment file for boot commands,
based on it, the series extends to support multiple block devices
(MMC and virtio). And the env file is extended for booting Debian.
The last commit is to update memory mapping info based on the DRAM info
passed via DT binding.
Link: https://lore.kernel.org/r/20241025171821.624702-1-leo.yan@arm.com
This commit introduces build_mem_map() function for updating the mem_map
structure with copying info from gd->bd->bi_dram, so that it can keep
the consistence for DRAM info passed via DT.
The page table size is calculated prior to mem_map is ready, introduce
the get_page_table_size() function for a predefined table size.
Signed-off-by: Leo Yan <leo.yan@arm.com>
Dynamically detect block device in the boot command, this allows to
support both MMC and virtio block devices.
Signed-off-by: Leo Yan <leo.yan@arm.com>
The boot command for Total Compute has many aspects and changes from time
to time. So move it to an .env file where it can be a proper script.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
The whole DRAM bank is used for loading and U-boot can detect the
overlap between the kernel and initramfs. So it is safe to drop
bootm_size.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Initialize the environment variables 'fdt_addr_r' and 'kernel_addr_r'
during the misc init phase. The static configurations are not needed,
remove them.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
On Total Compute, TF-A passes the info via DT binding for the hardware
description - includes the serial, memory, and arm_ffa nodes.
This commit initializes the fdt base address based on the passed the
register x1.
The similar implementation has already been done for the raspberry pi,
so borrow a lot of it.
Co-developed-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Andrew Goodbody <andrew.goodbody@linaro.org> says:
Starting a sandbox session and running 'ut bootm' on the command
line instead of using pytest with --verbose will result in some
test failures. This series makes the tests more deterministic so
that they will better control their environment and hence will
work as expected whether or not they are invoked with '--verbose'.
The series starts with a small fix to the parameters of
bootm_process_cmdline that one commit incorrectly added using a bool
when it had been updated to take flags by the preceeding commit.
Link: https://lore.kernel.org/r/20241101130254.473017-1-andrew.goodbody@linaro.org
Some bootm tests expect that GD_FLG_SILENT is reset in order
to work as expected. This is the state if the test is run with
'pytest --verbose' but not if run from, say, the sandbox command
line.
So reset the flag for those tests that rely on it being reset. This
has to be done in each test as the test infrastructure will set it
again before every test when not invoked with 'pytest --verbose'.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The function bootm_process_cmdline_env takes flags as its third
parameter, not a bool. Correct the usage by replacing 'true'
with BOOTM_CL_ALL so that the intent is clear.
A similar change was made throughtout this file in the previous
commit to the one mentioned below as being fixed.
Fixes: 4448fe8e4e7c ("bootm: Allow updating the bootargs in a buffer")
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The tests test_usb_ext4load_ext4write, test_usb_ext2load and
test_usb_load depend on the command ext4write being present not just
the feature of being able to write to an ext4 file system. So update
their dependencies to include the ext4write command itself. This will
prevent spurious test failures when running the USB tests against USB
storage with an ext2/ext4 partition but no ext4write command available.
Fixes: 1c5b6edad381 ("test/py: usb: Add tests for USB device")
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Love Kumar <love.kumar@amd.com>
When test_usb_load finds multiple partitions of the same type then
it will cause a test failure. The call to write the test file will
write a different test file to each partition but only return the
name and size of the last one written. So the test then fails to
load the test file from the first partition as it uses the name of
a file on a different partition.
Refactor the code so that only one test file is written at a time
and is written to only the partition being tested at that time. This
allows the correct file name to always be available to the code that
runs the load command. This reduces the number of files written and
also the number of calls to crc32 needed.
Fixes: 1c5b6edad381 ("test/py: usb: Add tests for USB device")
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Love Kumar <love.kumar@amd.com>
This is mostly hidden in the background, but it is sometimes useful to
look at it. Add a function to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tests which create a new bloblist overwrite the existing one in sandbox.
Provide a flag for tests to declare this behaviour. Save and restore the
bloblist pointer so that other tests remain unaffected.
Note that when sandbox is running normally, the bloblist has been
relocated to high in memory. The existing bloblist tests create a new
bloblist low in memory, so they do not conflict.
Correct a build error on coreboot by using accessors for gd->bloblist:
Signed-off-by: Simon Glass <sjg@chromium.org>
Coreboot provides the CMOS layout in the tables it passes to U-Boot.
Use that to build an editor for the CMOS settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Coreboot tables provide information about the CMOS-RAM checksum. Add a
command which can check and update this.
With this it is possible to adjust CMOS-RAM settings and tidy up the
checksum afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the cbsysinfo command to show the contents of the CMOS option
table.
While we are here, add some example output for this command, along with
mention of what the unimplemented tags are.
Signed-off-by: Simon Glass <sjg@chromium.org>
The timer counter on Rockchip SoCs may be reset in TF-A, this may cause
the bootstage records to be printed out of order and with an incorrect
elapsed time.
Fix this by not sorting the bootstage records.
Before on a Radxa ZERO 3W (RK3566) board:
=> bootstage report
Timer summary in microseconds (12 records):
Mark Elapsed Stage
0 0 reset
7,436 7,436 board_init_f
164,826 157,390 SPL
375,392 210,566 end phase
423,909 48,517 board_init_r
472,973 49,064 eth_common_init
476,848 3,875 main_loop
477,003 155 cli_loop
Accumulated time:
7,181 of_live
14,739 dm_spl
15,029 dm_r
315,150 dm_f
With this the records can be printed in chronological order when the
counter is reset and SPL and board_init_r records show correct elapsed
time.
=> bootstage report
Timer summary in microseconds (12 records):
Mark Elapsed Stage
0 0 reset
164,437 164,437 SPL
375,023 210,586 end phase
7,437 7,437 board_init_f
424,390 416,953 board_init_r
473,515 49,125 eth_common_init
477,402 3,887 main_loop
477,571 169 cli_loop
Accumulated time:
14,734 dm_spl
315,646 dm_f
7,339 of_live
14,977 dm_r
For the tested board external TPL and BROM take ~164 ms to initialize
DRAM and load SPL, SPL take ~210ms to load images from FIT and U-Boot
proper take ~477ms to reach cli prompt.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
When the buffer address is not set, say so, rather than showing an
address which looks very strange, on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function assumes that all tests in a suite are being run. This
means that it can sometimes call dm_test_restore() when it should not.
The impact of this is that it is not possible, for example, to run
'ut bootstd bootflow_cros' and then check the state of bootstd
afterwards, since all devices are removed and recreated.
Update the function to take account of any selected test, to avoid this
problem.
Add a comment for test_insert while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the bootflow tests the script bootmeth is bound with the name
bootmeth_script whereas the others have a name without the bootmeth_
prefix. Adjust it to be the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
All the uclass functions for finding a device end up creating a uclass
if it doesn't exist. Add a function which instead returns NULL in this
case.
This is useful when in the 'unbind' path, since we don't want to undo
any unbinding which has already happened.
Signed-off-by: Simon Glass <sjg@chromium.org>
