The latest ATF puts the U-Boot at 0x50000000, just like on all the other
boards. Adjust the text base to reflect that change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Test case:
The fitImage gets corrupted:
truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset
[board shall hang in SPL with
"Trying to boot from MMC1" information]
Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.
It removes the support for it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To test if this partition is present - one needs to write:
display5 > sf probe; mtdparts
display5 > sf erase factory +0x100000
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To avoid confusion, let's rename the efi-x86 target to efi-x86_app.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have generic EFI payload support for all x86 boards,
drop the QEMU-specific one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible to create a generic EFI payload for all x86 boards.
The payload is configured to include as many generic drivers as
possible. All stuff that touches low-level initialization are not
allowed as such is the EFI BIOS's responsibility. Platform specific
drivers (like gpio, spi, etc) are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The V3M Eagle uses flash with 128 kiB or 256 kiB sectors,
disable the 4k sector support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Turning the cache off can help when experimenting with bare metal
applications, enable the cache command on V3M Eagle to make that
easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This function is required for adding bootstage support.
Also enable it directly for ZynqMP R5 configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
The am3517-evm boards stores the environment in NAND, but after merging
various configs, the board was trying to load environment variables from
FAT which would ultimately fail and cause some chatter.
This patch removes the ENV_IS_IN_FAT flag to eliminate the noise.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add Panther Point chipset interrupt pin/PIRQ information, and
enable the generation of PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI application does not boot currently. It's due to the call
to syscon_get_by_driver_data() in cpu_init_r() maps to nowhere as
CONFIG_SYSCON is not included in the configuration.
EFI application is built as a shared library, so GCC won't complain
during the build process if some symbols are not found. GCC will
simply put these symbols into the .plt section and expect dynamic
loader to fix these up.
While we are here, remove some commands and drivers that are not
needed at present.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This enables the 206ax cpu driver on Intel Cougar Canyon 2 board,
so that SMP can be supported too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As README.x86 already mentions, there are two SPI flashes mounted
on Intel Cougar Canyon 2 board, called SPI-0 and SPI-1 respectively.
SPI-0 stores the flash descriptor and the ME firmware. SPI-1 stores
the actual BIOS image which is U-Boot. Building a single image with
both ME firmware and U-Boot does not make sense.
This also describes the exact flash location where the u-boot.rom
should be programmed in the documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
This disables networking related items in the config. The EV3 does not have
any networking hardware, so this is wasted space.
Signed-off-by: David Lechner <david@lechnology.com>
The SBx81LIFKW boards connect to the internal chassis management network
via a Marvell 88e6097 L2 switch. The chassis connections are direct
serdes on ports 8 and 9 with a RGMII interface on port 10 connected to
the CPU MAC.
For debugging purposes ports 0 and 1 are also taken out to headers on
the board. Because the debug interfaces are sometimes connected to with
straight ribbon cables we need to run them at 10Mbps.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch shows how to enable driver model support for the LS-CHLv2 and
LS-XHL boards.
There are a couple of open questions:
- do I need the u-boot,dm-pre-reloc tags in the device tree?
- should mach/config.h define CONFIG_DM_SEQ_ALIAS?
- how can we split this patch or are there any other pending patches
which does the same and I didn't catch these.
This patch is based on the http://git.denx.de/u-boot-marvell.git (master
branch) and needs the following patches, which are still pending:
https://patchwork.ozlabs.org/patch/909618/https://patchwork.ozlabs.org/patch/909617/https://patchwork.ozlabs.org/patch/909973/
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Synchronize it with the LS-XHL board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The a38x sata interfaces run in ahci mode and can
be accessed via the scsi command.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on current upstream]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
