Add a fixed partitions node to the AM64x device tree so that it can
be used to fixup the Linux device tree.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Add a fixed partitions node to the AM62x device tree so that it can
be used to fixup the Linux device tree.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Test whether this system is compatible with STM32MP15xx DHCOM SoM,
if so, test whether R292 pull up is populated on pin PC3, which is
an indication that the second MAC chip, KS8851-16MLL, is populated.
Use this information to patch 'status' DT property into the second
ethernet MAC DT node and enable/disable the MAC on systems where
the chip is/isn't populated respectively.
Use spl_perform_fixups() to patch the U-Boot proper DT from SPL and
ft_board_setup() to patch Linux DT from U-Boot proper. This way both
software components are configured the same way.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add generic SoM compatible string into machine compatible string
for all STM32MP15xx based DH electronics DHSOM. This way, common
board code can match on this compatible. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In Odyssey board, we should reset the PHY chipset, toggling G0 pin.
Signed-off-by: Heesub Shin <heesub@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In Odyssey board, KSZ9031 is at the PHY address 0x7, not 0x0. This
commit fixes it.
Signed-off-by: Heesub Shin <heesub@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In Odyssey board, we should use the internal clock from RCC as the
transmit clock, instead of the external clock from ETH_CLK125 pad. This
commit adds a property, st,eth-clk-sel, so that the ETH_CLK_SEL mux
selects ETH_CLK.
Signed-off-by: Heesub Shin <heesub@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Odyssey board requires ETH_CLK of 125Mhz. This commit sets PLL4_P/Q/R to
125, 62.5 and 62.5Mhz in respectively.
Signed-off-by: Heesub Shin <heesub@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This stm32mp135f-dhcor-dhsbc board is a stack of DHCOR SoM based on
STM32MP135F SoC (900MHz / crypto capabilities) populated on DHSBC
carrier board.
The SoM contains the following peripherals:
- STPMIC (power delivery)
- 512MB DDR3L memory
- eMMC and SDIO WiFi module
The DHSBC carrier board contains the following peripherals:
- Two RGMII Ethernet ports
- USB-A Host port, USB-C peripheral port, USB-C power supply plug
- Expansion connector
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Add both ethernet MACs based on GMAC SNPS IP on stm32mp13.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch makes STM32 PWR regulators available on stm32mp13xx.
This requires TFA to clear RCC_SECCFGR, is disabled by default
on stm32mp13xx and can only be enabled on board config level.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch adds STM32 PWR regulators DT support on stm32mp131.
This requires TFA to clear RCC_SECCFGR, is disabled by default
and can only be enabled on board DT level.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit 7b78d6438a2b3 ("efi_loader: Reserve unaccessible memory")
memory region above ram_top is tagged in EFI memory map as
EFI_BOOT_SERVICES_DATA.
In case of STM32MP1/STM32MP13 platforms, above ram_top, there is one
reserved-memory region tagged "no-map" dedicated to OP-TEE :
_ addr=de000000 size=2000000 for stm32mp157x-dkx and stm32mp135f-dk
_ addr=fe000000 size=2000000 for stm32mp157c-ev1
Before booting kernel, EFI memory map is first built, the OPTEE region is
tagged as EFI_BOOT_SERVICES_DATA and when reserving LMB, the tag LMB_NONE
is used.
Then after, the LMB are completed by boot_fdt_add_mem_rsv_regions()
which try to add again the same OPTEE region (addr=de000000 size=2000000
in case of stm32mp157x-dkx / stm32mp135f-dk or addr=fe000000 size=2000000
in case for stm2mp157c-ev1)
but now with LMB_NOMAP tag which produces the following error message :
_ for stm32mp157x-dkx / stm32mp135f-dk :
"ERROR: reserving fdt memory region failed (addr=de000000 size=2000000 flags=4)"
_ for stm32mp157c-ev1 :
"ERROR: reserving fdt memory region failed (addr=fe000000 size=2000000 flags=4)"
To avoid this, OPTEE area shouldn't be used by EFI, so we need to mark
it as reserved.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZnBfewAKCRDKSWXLKUoM
Ib/7AJ0cn3q7lMpxbSbRj33oftI8Vy8+owCeN35Nl8TN9l/DHbfusER4uVfnOVw=
=YMIB
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
Rename spl_board_init() to spl_soc_init(). SoC specific
implementation should be separated from board specific implementation
in order to be extended by board developers.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240327121153.2455126-3-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The zynqmp cmds.c is currently tied to the board but the commands
contained within are more closely tied to the architecture. To
allow usage of those commands when the architecture is ZynqMP but
the board is not, this change moves the cmds into the arch/ tree.
The source file is renamed to zynqmp.c to reflect the command name
as well.
Signed-off-by: Charlie Johnston <charlie.johnston@loftorbital.com>
Link: https://lore.kernel.org/r/20240410195008.405061-2-charlie.johnston@loftorbital.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add combined binaries for all Verdin AM62 variants.
These binaries can be used to flash the U-Boot via single
binary instead of few as it is done at the moment.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
The am625-lp-sk is a variant of the am625-sk showcasing the low-power
features of the am625 SoC Family. Because it's essentially a board and
package spin of the am625-sk I've inherited the am625 configuration and
overridden what was needed.
This is a new spin of Nitin's original work which has been updated
significantly since October 2023
https://lore.kernel.org/u-boot/20231030110138.1347603-1-n-yadav@ti.com/
For those of us interested here is proof of life using buildroot:
https://paste.sr.ht/~bryanb/40f7787f7760bee383aa8fbc342a29e8544dbdab
This also works around a buildman issue not following #include
directives. To get around this I've redefined the variables it's looking
for inside the lp-sk defconfig to keep it happy for now. I made a pull
request on github and everything seems like it's happy
https://dev.azure.com/u-boot/u-boot/_build/results?buildId=8634&view=results
Dhruva Gole <d-gole@ti.com> says:
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned in AM62A.
AM62P doesn't have any GP support, hence not applicable.
These changes are required for Low Power Mode features to work on these
SoCs as this TIFS Stub gets used in the Low Power Exit sequences.
Boot tested on both platforms that are being touched:
[0] AM62A, [1] AM62P
[0] https://gist.github.com/DhruvaG2000/d5f2a46818d8025a540efe9289feacb4
[1] https://gist.github.com/DhruvaG2000/ce29f6e9315a78d3e9e5810f55f17f43
Nishanth Menon <nm@ti.com> says:
Cleanup am625 on by switching over the last two platforms (SK and
beagleplay) over to OF_UPSTREAM, and while at it, switch over am62a7
(last of the am62* family) over as well.
This superscedes the previous version of beagleplay only patch[1]
Test logs: https://gist.github.com/nmenon/ba310d3750a80789aca6a4fd90190135
Adds TIFS stub binaries, this is required for deepsleep functionality.
This implements the same change as commit 128f81290b7d ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Add support for signing of TIFSSTUB images for HSSE, HSFS and GP devices
and include them in tispl.bin and tispl.bin_unsigned.
This implements the same change as commit 128f81290b7d ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Jonathan Humphreys <j-humphreys@ti.com> says:
Add binman nodes for EFI capsules of firmware components so that capsules
are automatically created during the UBoot builds.
This is enabled for several TI SoC based platforms: AM64, AM62, AM62p,
BeaglePlay, AM69, J7, and BeagleboneAI.
Fill in the BeagleBoneAI64's capsule GUID properties of the base binman
capsule nodes. Also add it's SYSFW binman capsule node.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Fill in the J721e SK's capsule GUID properties of the base binman capsule
nodes.
Also add it's SYSFW binman capsule node.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Enable OF_UPSTREAM for am62a7-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Enable OF_UPSTREAM for am625-sk board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Enable OF_UPSTREAM for AM625-beagleplay board. Remove DT files that
are now available in dts/upstream. Update the appended files based on
version of latest OF_UPSTREAM sync point (v6.10-rc1).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3588.
It provides the following feature set:
* up to 16GB LPDDR4x
* on-module eMMC
* SD card (on a baseboard) via edge connector
* Gigabit Ethernet with on-module GbE PHY
* HDMI/eDP
* MIPI-DSI
* 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
* HDMI input over FPC connector
* CAN
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 host
* PCIe
- 1x PCIe 2.1 Gen3, 4 lanes
- 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
* on-module ATtiny816 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
* on-module Secure Element with Global Platform 2.2.1 compliant
JavaCard environment
The support is added for Tiger on Haikou devkit, similarly to RK3399
Puma and PX30 Ringneck.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On px30-ringneck the FIT payload is located at sector 0x200 compared to
the more Rockchip common sector 0x4000 offset:
SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
Because FIT payload is located at sector 0x200 and the TPL+SPL is
located at sector 64, the combined size of TPL+SPL cannot take up more
than 224KiB:
(0x200 - 64) x 512 = 0x38000 (224 KiB)
Adjust SPL_PAD_TO to match the used 0x200 sector offset.
While at it, update the px30-ringneck-u-boot.dtsi to remove the now
unnecessary override of simple-bin:fit:offset since SPL_PAD_TO matches
with the current formula.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Since commit 6007b69d544e ("rockchip: rk3399-puma: Update SPL_PAD_TO
Kconfig option"), SPL_PAD_TO matches
(CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR - 64) * 512 and the default
value for simple-bin:fit:offset in rockchip-u-boot.dtsi is
SPL_PAD_TO, so let's remove this override.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
ArmSoM Sige7 is a Rockchip RK3588 based SBC (Single Board Computer) by
ArmSoM.
There are two variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MC4 GPU
2x MIPI CSI 2 multiple lanes connector
64GB/128GB on board eMMC
uSD slot
1x USB 2.0 Type-A, 1x USB 3.0 Type-A, 1x USB 3.0 Type-C
1x HDMI 2.1 output
2x 2.5 Gbps Ethernet port
40-pin IO header including UART, SPI and I2C
USB PD over USB Type-C
Size: 92mm x 62mm
Kernel commit:
81c828a67c78 (arm64: dts: rockchip: Add ArmSom Sige7 board)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After we sync USB3 DRD nodes from v6.10-rc1, these obsolete nodes
can be removed.
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate PX30/RK3326 boards that exists in Linux v6.8 to use OF_UPSTREAM.
firefly-px30 is not migrated to OF_UPSTREAM because there's no Device
Tree in the Linux kernel.
Differences between U-Boot's Odroid-Go2 and Linux's are now moved to the
-u-boot.dtsi, though I have a gut feeling that the existing cru
overrides aren't necessary (anymore?).
The U-Boot GPIO led-0 is on GPIO0_C1 but such is the pin of PWM3 which
is used for Linux's PWM led-2 so keep Linux's.
I also doubt vcc_cam is actually used, though the Odroid-Go2 Black
Edition uses this dcdc regulator for WiFi, so let's just move it to the
-u-boot.dtsi to play it safe.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This adds the default pinmux for UART2 and UART5 to the TPL/SPL DTB (if
not removed through the CONFIG_OF_SPL_REMOVE_PROPS symbol) as those two
controllers are always made available to all boards.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The default DM firmware path is non-optional as of now. Make it
optional so that users that choose to provide DM via TI_DM argument
instead of BINMAN_INDIRS can do so without build errors.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
MAIN_PLL0 has a flag set in DM (Device Manager) that removes its
capability to re-initialise clock frequencies. A72 CPU clock (GTC) and
RGMII has MAIN_PLL3 as their parent which does not have this flag. While
RGMII needs re-initialization to default frequency to be able to get
250MHz with its divider, GTC can not get its required 200MHz with its
dividers. Thus move GTC clock parent on J721S2 from MAIN_PLL3_HSDIV1 to
MAIN_PLL0_HSDIV6. This was already done on CPTS node in kernel which was
similarly affected (linked).
Link: https://lore.kernel.org/all/20230605110443.84568-1-n-francis@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
