net.h is needed for PKTBUFSRX. Without this definition, the driver will
always use 4 RX buffers, causing am65-cpsw-nuss initialization to fail
when a higher number of buffers is requested.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
The eth-uclass state machine doesn't prevent imbalanced start()/stop()
calls - to the contrary, it even provides eth_init_state_only() and
eth_halt_state_only() functions that change the state without any calls
into the driver. This means that the driver must be robust against
duplicate start() and stop() calls as well as send/recv calls while the
interface is down.
We decide not to print error messages but just to return an error in the
latter case, as trying to send packets on a disabled interface commonly
happens when the netconsole is still active after the Ethernet has been
halted during bootm.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
AM62A has a R5F core in MCU voltage domain.
Extend support for R5F remote proc driver on AM62A with compatible
strings.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
AM62A SoC has a single C71x DSP subsystem with analytics engine in
main voltage domain. Extend support to AM62A with compatible strings.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Martyn Welch <martyn.welch@collabora.com> says:
This series adds DFU support for TI AM62 SK and beagleplay boards.
I have picked this series up from Sjoerd due to time constraints.
Since the last revision:
* Removed dwc3 mode setting in favour of reinstating forced peripheral
mode for usb0
* Use of config fragments for both r5 and a53 DFU configuration to
reduce duplication
* Typographical improvements to documentation
We plan to also submit the dts changes to linux so that those can be
dropped again in the near future (hopefully)
Add glue code for TI AM62 to the dwc3 driver; Most code adopted from
TI vendor u-boot code.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on beagle play
Without the NULL check, if the devicetree that u-boot loads does not have a
compatible property then a store access fault will be raised and force the
machine to reset, due to the NULL pointer we passed to strlen. This commit
adds this check and will return -ENOSPC to indicate the get_desc failed.
Signed-off-by: Hanyuan Zhao <zhaohy22@mails.tsinghua.edu.cn>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When the device port is in a low power state [U3/L2/Not Connected],
accesses to usb device registers may take a long time. This could lead to
potential core hang when the controller registers are accessed after the
port is disabled by setting DEVDS field. Setting the fast register access
bit ensures that the PHY clock is keeping up in active state.
Therefore, set fast access bit to ensure the accesses to device registers
are quick even in low power states.
commit b5148d946f45 ("usb: cdns3: gadget: set fast access bit") in the
upstream kernel is taken as reference.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240424073911.1943-1-r-gunasekaran@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Roger Quadros <rogerq@kernel.org> says:
Sync AM62 device tree files with Linux v6.9 and
add in the missing bits in -u-boot.dtsi to get CPSW
Ethernet working.
CI testing: https://github.com/u-boot/u-boot/pull/534
MD Danish Anwar <danishanwar@ti.com> says:
This series adds AM64x related compatibles to PRUSS and PRU_RPROC drivers.
This series is a prerequisite for ICSSG Ethernet driver.
Once Support for AM64x is added to PRUSS and PRU_RPROC driver, I'll send
another series to enable ICSSG Ethernet driver for AM64x as well.
Add support for AM64x by adding it's compatible in pruss driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Add support for AM64x PRU cores by adding compatibles for AM64x.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
This driver support the Synopsys Designware Ethernet 10G
IP block refer from the driver dwc_eth_qos.
The driver MAC register mapping is different between
Synopsys QoS IP and Synopsys 10G IP, and thus new file
is created meant for Sysnopsys 10G IP.
The dwc_eth_xgmac_socfpga.c is specific to a device family,
the driver support the specific configuration used in
Intel SoC FPGA Agilex5.
This driver is extensible for other device family to use.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
This adds support for the SC5XX clock trees which are required for reading
clock speeds on the SoCs. This is largely a port of the same support for
Linux, which has not yet been submitted upstream.
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
