The device tree for Firefly-RK3288 in dts/upstream can be used as-is by
U-Boot, migrate board to use OF_UPSTREAM.
Add chosen stdout-path prop to board u-boot.dtsi as it is missing in DT
from dts/upstream. Also change to use the upstream power_led symbol.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph props and enable related Kconfig options to include the sdmmc
regulator in SPL. Also enable SPL_DM_SEQ_ALIAS to ensure aliases is
handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph- props to emmc, sdmmc, uart and related pinctrl nodes to
ensure devices and pinctrl can be used in xPL and U-Boot pre-reloc.
Remove the explicit bootph-all prop from the pinctrl node, any bootph-
prop will automatically be propagated to the pinctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort the nodes in rk3288-firefly-u-boot.dtsi in alphabetical order.
This has no intended change to board DT, this only rearrange nodes in
preparation for future changes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The firefly-rk3288_defconfig build target does not enable the SPL_LED
Kconfig option.
Drop the unused SPL_LED related code and replace it with a default-state
prop to ensure the LED driver enable the LED at U-Boot proper phase.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The reset mechanism used by Linux to reset the SoC is known to only
partially reset the logic. A mechanism is implemented in
rk3399_force_power_on_reset to use a GPIO connected to the PMIC's
over-temperature (OTP) reset pin, which fully resets all logic.
Hook the associated GPIO where the function expects it to enable this
reset mechanism and avoid any possible side-effect of partially-reset
units.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The reset mechanism used by Linux to reset the SoC is known to only
partially reset the logic. A mechanism is implemented in
rk3399_force_power_on_reset to use a GPIO connected to the PMIC's
over-temperature (OTP) reset pin, which fully resets all logic.
Hook the associated GPIO where the function expects it to enable this
reset mechanism and avoid any possible side-effect of partially-reset
units.
Without this patch, reading from the micro sd slot fails after a reset.
With this mechanism, U-Boot is able to boot from it reliably.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
MiQi use RTL8211 Ethernet PHY, datasheet list an initial 10ms delay and
then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for mqmaker MiQi in dts/upstream can be used as-is by
U-Boot, migrate board to OF_UPSTREAM.
The change to use DT from dts/upstream will include minor changes and
fixes related to work led and usb otg.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph props and enable related Kconfig options to include the sdmmc
regulator in SPL. Also enable SPL_DM_SEQ_ALIAS to ensure aliases is
handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph- props to emmc, sdmmc, uart and related pinctrl nodes to
ensure devices and pinctrl can be used in xPL and U-Boot pre-reloc.
Remove the explicit bootph-all prop from the pinctrl node, any bootph-
prop will automatically be propagated to the pinctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The work led is not used in xPL on rk3288-miqi, remove bootph props from
the work led node to exclude it from xPL control FDT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort the nodes in rk3288-miqi-u-boot.dtsi in alphabetical order.
This has no intended change to board DT, this only rearrange nodes in
preparation for future changes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For some reason the Ethernet PHY reset delay is set to 1 second, this
cause an unneccecery long boot delay.
Tinker Board use RTL8211E or RTL8211F Ethernet PHY, datasheet list an
initial 10ms delay and then a 30-76ms delay before accessing registers.
Change to use 80ms delay instead of a full second to speed up Ethernet
initializion in U-Boot.
Also enable PHY_REALTEK, DM_ETH_PHY and PHY_GIGE to improve Ethernet PHY
support in U-Boot.
Before:
1,404,971 960,924 eth_common_init
2,438,830 1,033,859 eth_initialize
2,444,449 5,619 main_loop
2,445,153 704 cli_loop
After:
1,404,987 960,710 eth_common_init
1,519,110 114,123 eth_initialize
1,524,734 5,624 main_loop
1,525,452 718 cli_loop
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for ASUS Tinker Board and S variant in dts/upstream can
be used as-is by U-Boot, migrate board to OF_UPSTREAM.
The change to use DT from dts/upstream will include minor changes and
fixes related to leds and regulators.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include mmc related nodes in U-Boot proper pre-reloc phase to ensure
environment can be loaded from mmc devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The sdmmc power come from vcc33_sd pmic regulator and not from the
vcc_sd fixed regulator, as currently defined in the in-tree DT.
Drop vcc_sd and the related gpio7 and sdmmc_pwr nodes from being
included in SPL along with any related Kconfig option. Also enable
SPL_DM_SEQ_ALIAS to ensure aliases is handled correctly in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop the unneeded bootph-all prop from dmc node, it is already defined
in soc u-boot.dtsi.
Remove booth-all prop from gpio7 node, this node is not needed in TPL.
Adjust bootph props to include pinctrl related nodes for UART2.
Remove the explicit bootph-all prop from the pinctrl node, any bootph-
prop will automatically be propagated to the pinctrl node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort the nodes in rk3288-tinker u-boot.dtsi files in alphabetical order.
This has no intended change to board DTs and only rearrange nodes in
preparation for future changes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vop nodes does not need to be included in xPL control FDT, they only
need to be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3288.dtsi from arch/arm/dts is almost identical to the rk3288.dtsi
from dts/upstream, it differs only with a minor change in hdmi port
nodes, something that does not affect U-Boot.
Remove arch/arm/dts/rk3288.dtsi to use rk3288.dtsi from dts/upstream.
Also drop gpio aliases from -u-boot.dtsi that has been part of
rk3288.dtsi for some time.
No functional change to board DTs is intended with this removal.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move to using OF_UPSTREAM config and thus using the devicetree
subtree and remove unused device tree files.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
The Texas Instruments Foundational Security (TIFS) firmware must match
the security level configured on the SoC. To boot Security Enforced (SE)
variants of the AM62Px, add another tiboot3 build which packages the
Security Enforced (SE) firmware variant for AM62Px SoCs.
Signed-off-by: Bryan Brattlof <bb@ti.com>
OSPI Boot requires overrides specific to R5 and also
to use DMA in R5 SPL stage the DM_TIFS needs to be used.
Add the corresponding overrides for R5 SPL stage.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Describe APMU controller as a remoteproc device capable of starting
the Cortex-R52 cores in Renesas R8A779G0 V4H SoC DT. The APMU IP is
in fact a power management unit capable of additional operations, but
those are not used by U-Boot so far.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This DTC_FLAGS assignment is no longer necessary as all R-Car Gen2/Gen3/Gen4
platforms have been converted to OF_UPSTREAM and matching DTC_FLAGS assignment
is present in dts/upstream/src/arm64/Makefile . Drop the remnant.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for building U-Boot SPL for Renesas R-Car Gen4 R8A779G0 V4H SoC.
The SPL initializes the DBSC5 DRAM controller, RT-VRAM and loads and starts
U-Boot proper on the Cortex-A76 core.
The SoC BootROM can not boot the CA76 core directly, instead the SPL starts
on the CR52 core which immediately brings up the CA76 core, which in turn
starts executing the actual SPL. This is achieved by placing a tiny bit of
precompiled Aarch32 code at the very beginning of the SPL. The code consists
of some 32 instructions, uses APMU to configure CA76 start address to offset
0x80 Bytes from start of the SPL, and uses APMU to start the CA76 core. The
code parts the CR52 core in an endless loop once the CA76 core got started.
The 32 instructions are completely arbitrary number, so is the offset 0x80
Bytes from start of SPL, because 0x80 = 128 decimal and 128 / 4 bytes per
instruction is 32 instructions. The 32 instructions turned out to be enough
to started the CA76 and 0x80 is nicely aligned.
Once the SPL completes hardware initialization, the SPL loads U-Boot proper.
The u-boot.itb proper fitImage contains 64bit build on u-boot-nodtb.bin and
a DT for R8A779G0 V4H White Hawk board and is generated by binman. The
u-boot.itb is loaded from SPI NOR offset 0x80000.
In order to install this setup on an existing R8A779G0 V4H White Hawk board,
build using r8a779g0_whitehawk_defconfig, generate SPI NOR image flash.bin
and write flash.bin to SPI NOR offset 0x0 . Finally, configure board MD pin
switches according to the R8A779G0 V4H White Hawk board documentation for
40 MHz SPI NOR boot using DMA and restart the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Describe DBSC5 DRAM controller and RT-VRAM configuration interface
as two new DT nodes in R-Car Gen4 R8A779G0 U-Boot DT extras file.
This node is used by the U-Boot SPL for R8A779G0 SoC, where the
DBSC5 and RT-VRAM drivers bind to these nodes and bring up the
DRAM controller and RT-VRAM settings respectively, so U-Boot
proper can be loaded into DRAM and started on Cortex A76 core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The GW7905 was renamed to GW7500 before release. Change the various
names in the dt files and references.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The root oscillators reference used to be in rcc node since
3d15245502c4 ("ARM: dts: stm32mp1: explicit clock reference needed by RCC clock driver")
however this is not part of upstream stm32mp151.dtsi . The
RCC driver does need this reference, reinstate it locally.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The root oscillators reference used to be in rcc node since
3d15245502c4 ("ARM: dts: stm32mp1: explicit clock reference needed by RCC clock driver")
however this is not part of upstream stm32mp151.dtsi . The
RCC driver does need this reference, reinstate it globally.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit 61ff13283c3b ("board: sl28: move to OF_UPSTREAM") USB0 is
broken because the former u-boot soc dtsi was setting dr_mode to "host"
but the linux device tree isn't. That is because linux fully supports
OTG but u-boot doesn't. Therefore, u-boot only ever enabled host mode
and never OTG mode. Add it to our board "-u-boot.dtsi" to fix it.
Fixes: 61ff13283c3b ("board: sl28: move to OF_UPSTREAM")
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Anurag Dutta <a-dutta@ti.com> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/20241129113136.383277-1-a-dutta@ti.com
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Add 32-bit address overrides for Hyper Bus Memory Controller
for Hyperflash to be functional in R5 SPL.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
Wadim Egorov <w.egorov@phytec.de> says:
This implements capsule updates for all our K3 SoMs for
eMMC, OSPI NOR and uSD cards.
We can use capsule updates to update the bootloader on all our
supported flash devices.
Link: https://lore.kernel.org/r/20241127121736.1525948-1-w.egorov@phytec.de
The correct spelling is R-Car, including the dash, update the usage.
Comment change only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
