Add the special pins configuration data to allow setup the bias
of the UFS and SDCard pins on the SM8250 SoC.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Leverage the data introduced in the struct msm_special_pin_data to allow
setting the gpio direction and value if supported by the pin data.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Add Qualcomm QMP UFS PHY driver which is available on the following
Snapdragon SoCs - SDM845, SM8250, SM8550 and SM8650 SoCs.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Import Qualcomm QMP phy related header files from Linux v6.11-rc7,
limit to headers needed to setup QMP v2 to v6 UFS PHYs.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable clk and pinctrl for sm8150
Signed-off-by: Julius Lehmann <lehmanju@devpi.de>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Add pinctrl and GPIO driver for SM8150. Driver code is based on the
similar U-Boot drivers. All constants are taken from the corresponding
Linux driver. This drivers differs from the similar U-Boot drivers,
because SM8150 SoC have different function IDs for the same functions
on different pins.
Co-authored-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Julius Lehmann <lehmanju@devpi.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Add clock, reset and power domain driver for SM8150. Driver code is
based on the similar U-Boot drivers. All constants are taken from the
corresponding Linux driver.
This driver supports clock rate setting only debug UART,
RGMII/Ethernet modules and USB controller.
Co-authored-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Julius Lehmann <lehmanju@devpi.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
The LXR2 board has a DA9063 that can provide watchdog functionality.
The DA9063 watchdog can cause a full POR reset, which is preferred
over the built-in i.MX6 watchdog.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The DA9063 PMIC is a multi-function device that provides
regulator, watchdog, RTC, and ON key functionalities.
Add support for the DA9063 PMIC watchdog functionality.
Based on the 6.11 kernel drivers/watchdog/da9063_wdt.c driver.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This shows up in 'help' output and introduces bogus gap:
"
mfgprot - Manufacturing Protection
mii - MII utility commands
"
Drop the newline to fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
The eMMC device on imx8mm-cl-iot-gate seems not support hs400.
When booting 6.1.0 kernel we got the following error.
mmc2: mmc_select_hs400es failed, error -110
mmc2: error -110 whilst initialising MMC card
Add no-mmc-hs400 to mmc2 node solves the problem.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
With the introduction of downstream Linux 6.6, the iMX8MP VPU block
control node in DTS was renamed "blk-ctl@38330000" and will not match
the ones found in `node_path_imx8mp` resulting in the node not being
disabled on the VPU-less variants.
Add an extra node_path entry for imx8mp VPU block control that match
with downstream Linux.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When supporting partition reset for SoC such as i.MX95 , the Linux
Kernel may have configured the tuning, while after force reset by
wdog or else, uboot CMD0 will never pass unless config RSTT to reset
tuning logic.
Since RSTA and RSTT are independent, so need both to be reseted in the
controller.
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The memory of priv and plat are leaked if max_bus_width is wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The plat->cfg is wrongly memset to 0, so the host_caps value configured
in fsl_esdhc_initialize is reset. Remove the unnecessary memset since
plat is allocated via calloc.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to SD and MMC spec, 74 clocks must be sent to device after
power stable. This is need in reinit ops for DM MMC or init ops for
non-DM MMC after power cycle.
So set the INTIA to send 80 clocks in esdhc_init_common and move
its calling from probe to reinit.
However, on 8MQ EVK and 8QXP MEK with some brands of SD cards, sending
80 clocks may not work well.
The root cause is related with power up time. According to spec, after
power stable, host shall supply at least 74 SD clocks to the SD card with
the maximum of 1ms. However, the power ram up time is related with the
characteristic of SD card. At the moment of sending 74 SD clocks, the
power probably not ram up to the operating level on the problematic
cards. Then cause the cards not ready.
This patch changes to send SD clock with 1ms duration to replace 80
SD clocks (0.2ms at 400Khz clock).
This way meets the spec requirement as well, and adds the margin for
power ram up time to be compatible with the problematic SD cards.
This is also aligned with implementation which has FORCE clock
always on.
Reviewed-and-tested-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With partition reset supported for i.MX8QM/QXP/95 and etc, when linux
mmc runtime suspended, the mmc clks are gated off. While at same time
system controller reset Cortex-A cores because of various reasons(
WDOG timeout and etc), with SPL run again, only enable PER clk is not
enough, also need to enable AHB/IPG clk, here use clk bulk API to enable
all the clocks.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
So we can disable to build ADP5585 in SPL to save size
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for DH electronics i.MX8MP DHCOM SoM on DRC02 carrier board.
This system is populated with two ethernet ports, two CANs, RS485 and RS232,
USB, capacitive buttons and an OLED display.
Matching Linux kernel patch has been posted:
https://lore.kernel.org/imx/20240925160343.84388-2-marex@denx.de/
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PicoITX carrier board.
This system is populated with serial console, EQoS ethernet, eMMC, SD, SPI NOR,
LEDs and USB 3.0 host used in USB 2.0 mode on PicoITX.
Matching Linux kernel patch has been posted:
https://lore.kernel.org/imx/20240928234949.357893-2-marex@denx.de/
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
u-boot-dfu-next-20241003
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/22516
DFU:
- Reinitialize only if dfu_alt_info changed
USB Gadget:
- New usb gadget driver for Renesas USBHS
- Simplify kconfig deps for CMD_USB_MASS_STORAGE
Android:
- Provide bootloader version to android via kernel commandline
This driver should not generally be present in SPL, even if misc devices
are enabled. Update the Makefile rule accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow MMC init when clock support is not enabled in a particular phase.
Refactor the setting of priv->emmc_clk so it is a bit clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
When MMC booting fails it is sometimes hard to figure out what went
wrong as there is no error code. It isn't even clear which MMC device
was chosen, since SPL can have its own numbering.
Add some debugging to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are currently four symbols here, so drop the word 'two'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Separate BSS is current mandatory on armv8 but this is not useful for
early boot phases. Add support for the combined BSS.
Use an #ifdef to avoid using CONFIG_SPL_BSS_START_ADDR which is not
valid in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The sprintf() etc. functions are supposed to return the length of the
string written, but do not. Fix this by checking the amount of buffer
space used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before
commit da3447d09fa0 ("android: Fix ramdisk loading for bootimage v3+"),
the ramdisk was loaded from img_data.ramdisk_ptr, ignoring offset
provided via mkbootimg.
commit da3447d09fa0 ("android: Fix ramdisk loading for bootimage v3+")
rightfully fixes this by switching to use img_data.ramdisk_addr instead.
However, it does not copy the ramdisk content to img_data.ramdisk_addr
in case we use boot image v2.
Because of this, we can no longer boot Android on Khadas vim3 board:
[ 3.940361] RAMDISK: Couldn't find valid RAM disk image starting at 0.
Add the missing memcpy() to fix the issue.
Fixes: da3447d09fa0 ("android: Fix ramdisk loading for bootimage v3+")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Oliver Gaskell <Oliver.Gaskell@analog.com> says:
ADSP-SC5xx is a series of ARM-based DSPs.
This comprises the armv7 based SC57x, SC58x and SC594 series, and the
armv8 based SC598.
This patch series includes configurations, init code, and minimal DTs
to enable Analog Devices' evaluation boards for these SoCs to boot
through SPL and into U-Boot Proper, as well as devicetree schemas for
the added DTs.
This patch series depends on ("arm: Add Analog Devices SC5xx Machine
Type") (https://lists.denx.de/pipermail/u-boot/2024-April/552043.html)
Adds support for Analog Devices' SC589-MINI board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Adds support for Analog Devices' SC589-EZKIT board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Adds support for Analog Devices' SC594-SOM-EZLITE board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Adds support for Analog Devices' SC598-SOM-EZLITE board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
