Implement the .get_function operation, so the gpio command can report
the current function. Since the GPIOF_FUNC (versus GPIOF_UNUSED) mux
values vary among the PMICs, report all non-GPIO mux values as UNKNOWN.
Signed-off-by: Samuel Holland <samuel@sholland.org>
There are three major variants of the AXP PMIC GPIO functionality (plus
PMICs with no GPIOs at all). Except for GPIO3 on the AXP209, which uses
a different register layout, it is straightforward to support all three
variants with a single driver. Do this, and in the process remove the
GPIO-related definitions from the PMIC-specific headers, and therefore
the dependency on AXP_PMIC_BUS.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC driver implements the DM_PMIC uclass, those functions
can be used instead of the platform-specific "pmic_bus" functions.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it still depends on one of those
choices, and therefore also AXP_PMIC_BUS.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the PMIC has a DM driver and binds device tree subnodes, the
GPIO device can be bound that way, instead of from inside board code.
Since the driver still uses the single set of register definitions from
axpXXX.h (as selected by AXPxxx_POWER), it does not differentiate among
the supported compatibles.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This is less confusing than half of the driver using "axp_gpio" and the
other half using "gpio_axp".
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, we can switch to DM_GPIO for these pins with no loss in
functionality. Since the driver now gets its pin configuration from
the device tree, we can remove the Kconfig symbols.
Signed-off-by: Samuel Holland <samuel@sholland.org>
While R40 puts the EMAC syscon register at a different address from
other variants, the relevant portion of the register's layout is the
same. Factor out the register offset so the same code can be shared
by all variants. This matches what the Linux driver does.
This change provides two benefits beyond the simplification:
- R40 boards now respect the RX delays from the devicetree
- This resolves a warning on architectures where readl/writel
expect the address to have a pointer type, not phys_addr_t.
Series-to: sunxi
Cover-letter:
net: sun8i-emac: Allwinner D1 Support
D1 is a RISC-V SoC containing an EMAC compatible with the A64 EMAC.
However, there are a couple of issues with the driver preventing it
being built for RISC-V. These are resolved by patches 2-3. Patch 1 is
a general cleanup.
END
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove
it, along with the rest of the support for AXP virtual GPIOs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Since the D1 CCU binding is defined, we can add support for its
gates/resets, following the pattern of the existing drivers.
Series-to: sunxi
Signed-off-by: Samuel Holland <samuel@sholland.org>
The device tree binding for the PHY provides VBUS supplies as regulator
references. Now that all boards have the appropriate regulator uclass
drivers enabled, the PHY driver can switch to using them. This replaces
direct GPIO usage, which in some cases needed a special DM-incompatible
"virtual" GPIO from the PMIC.
The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
missing the "usb0_vbus-supply" property in their device tree. None of
them have the MUSB controller enabled in host or OTG mode, so they
should see no impact:
- Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
- Ampe_A76_defconfig / sun5i-a13-ampe-a76
- CHIP_pro_defconfig / sun5i-gr8-chip-pro
- Cubieboard4_defconfig / sun9i-a80-cubieboard4
- Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
- Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
- Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
- Yones_Toptech_BS1078_V2_defconfig /
sun6i-a31s-yones-toptech-bs1078-v2
- iNet_3F_defconfig / sun4i-a10-inet-3f
- iNet_3W_defconfig / sun4i-a10-inet-3w
- iNet_86VS_defconfig / sun5i-a13-inet-86vs
- iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
- icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
- sun8i_a23_evb_defconfig / sun8i-a23-evb
Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
have "usb1_vbus-supply" in their device tree. Neither of them have USB
enabled at all, so again there should be no impact:
- Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
- sun8i_a23_evb_defconfig / sun8i-a23-evb
The following boards use a different pin for USB1 VBUS between their
defconfig and their device tree. Depending on which is correct, they
may be broken:
- Linksprite_pcDuino3_Nano_defconfig (PH11) /
sun7i-a20-pcduino3-nano (PD2)
- icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
Finally, this board has conflicting pins given for its USB2 VBUS:
- Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that some regulator driver exists for this PMIC, add support for
probing regulator drivers from the device tree subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
The first AXP regulator converted to use the regulator uclass is the
drivevbus switch, since it is used by the USB PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This driver reports the presence/absence of voltage on the PMIC's USB
VBUS pin. This information is used by the USB PHY driver. The
corresponding Linux driver uses the power supply class, which does not
exist in U-Boot. UCLASS_REGULATOR seems to be the closest match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
When MMC_WRITE is disabled this driver produced a build error. Fix this.
Also update a comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use the correct SPL_TPL_ variable so that these features can be enabled in
TPL and VPL as needed.
Disable it by default in TPL to avoid any code-size increase. No boards
are actually using it since the Makefile rules don't allow including
drivers/block/ with TPL_DM enabled. It can be manually enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add test coverage for blk_write() as well.
The blk_erase() is not tested for now as the USB stor interface does not
support erase.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have functions called blk_dread(), etc., which take a
struct blk_desc * to refer to the block device. Add some functions which
use udevice instead, since this is more in keeping with how driver model
is supposed to work.
Update one of the tests to use this.
Note that it would be nice to update the functions in disk-uclass.c to use
these new functions. However they are not quite the same. For example,
disk_blk_read() adds the partition offset to 'start' when calling the
cache read/fill functions, but does not with part_blk_read(), which does
the addition itself. So as designed the code is duplicated.
Signed-off-by: Simon Glass <sjg@chromium.org>
STI timer is actually ARM Cortex A9 global timer. Convert the driver to
use generic global timer name and make it consistent with Linux kernel
global timer driver. This also allows any A9 based device to use this
driver.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
As CONFIG_ARCH_BCM6753 is replaced with CONFIG_BCM6855, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM6858 is replaced with CONFIG_BCM6858, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM68360 is replaced with CONFIG_BCM6856, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM63158 is replaced with CONFIG_BCM63158, update the
Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
