The boot_fdt_add_mem_rsv_regions() function can be called twice, e.g.
first time during the board init (as a part of LMB init), and then when
booting the OS with 'booti' command:
lmb_add_region_flags
lmb_reserve_flags
boot_fdt_reserve_region
boot_fdt_add_mem_rsv_regions
^
|
+-----------------------+
| (1) | (2)
lmb_reserve_common image_setup_linux
lmb_init ...
initr_lmb do_booti
board_init_r 'booti'
That consequently leads to the attempt of reserving the same memory
areas (described in the 'reserved-memory' dts node) in LMB. The
lmb_add_region_flags() returns -EEXIST error code in such cases, but
boot_fdt_reserve_region() handles all negative error codes as a failure
to reserve fdt memory region, printing corresponding error messages,
which are essentially harmless, but misleading. For example, this is the
output of 'booti' command on E850-96 board:
=> booti $loadaddr - $fdtaddr
...
ERROR: reserving fdt memory region failed
(addr=bab00000 size=5500000 flags=2)
ERROR: reserving fdt memory region failed
(addr=f0000000 size=200000 flags=4)
...
Starting kernel ...
The mentioned false positive error messages are observed starting with
commit 1d9aa4a283da ("lmb: Fix the allocation of overlapping memory
areas with !LMB_NONE"), which removes the check for the already added
memory regions in lmb_add_region_flags(), making it return -1 for
!LMB_NONE cases. Another commit 827dee587b75 ("fdt: lmb: add reserved
regions as no-overwrite") changes flags used for reserving memory in
boot_fdt_add_mem_rsv_regions() from LMB_NONE to LMB_NOOVERWRITE. So
together with the patch mentioned earlier, it makes
lmb_add_region_flags() return -1 when called from
boot_fdt_reserve_region().
Since then, the different patch was implemented, returning -EEXIST error
code in described cases, which is:
lmb: Return -EEXIST in lmb_add_region_flags() if region already added
Handle -EEXIST error code as a normal (successful) case in
lmb_reserve_flags() and don't print any messages.
Fixes: 1d9aa4a283da ("lmb: Fix the allocation of overlapping memory areas with !LMB_NONE")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
An attempt to add the already added LMB region using
lmb_add_region_flags() ends up in lmb_addrs_overlap() check, which
eventually leads to either returning 0 if 'flags' is LMB_NONE, or -1
otherwise. It makes it impossible for the user of this function to catch
the case when the region is already added and differentiate it from
regular errors. That in turn may lead to incorrect error handling in the
caller code, like reporting misleading errors or interrupting the normal
code path where it could be treated as the normal case. An example is
boot_fdt_reserve_region() function, which might be called twice (e.g.
during board startup in initr_lmb(), and then during 'booti' command
booting the OS), thus trying to reserve exactly the same memory regions
described in the device tree twice, which produces an error message on
second call.
Return -EEXIST error code in case when the added region exists and it's
not LMB_NONE; for LMB_NONE return 0, to conform to unit tests
(specifically test_alloc_addr() in test/lib/lmb.c) and the preferred
behavior described in commit 1d9aa4a283da ("lmb: Fix the allocation of
overlapping memory areas with !LMB_NONE"). The change of
lmb_add_region_flags() return values is described in the table below:
Return case Pre-1d9 1d9 New
-----------------------------------------------------------
Added successfully 0 0 0
Failed to add -1 -1 -1
Already added, flags == LMB_NONE 0 0 0
Already added, flags != LMB_NONE 0 -1 -EEXIST
Rework all affected functions and their documentation. Also fix the
corresponding unit test which checks reserving the same region with the
same flags to account for the changed return value.
No functional change is intended (by this patch itself).
Fixes: 1d9aa4a283da ("lmb: Fix the allocation of overlapping memory areas with !LMB_NONE")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
Since RPI works well using EFI and has no size limitations with regards
to U-Boot, add the needed structures to support capsule updates.
While at it update the most commonly used defconfigs and include capsule
support and U-Boot commands needed by EFI
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For a lot of usecases, such as display, camera, media
the Raspberry Pi needs a lot more CMA than distros
configure as default so we should pass this parameter
through so things work as expected. Fix a spelling
mistake while we're at it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Comment changes only, no functional change.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Comment change only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
As the "peer-hub" property is optional, don't error out just
skip the bind function.
Fixes: 57e30b09fc ("usb: onboard-hub: Bail out if peer hub is already probed")
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
The U-Boot is currently not capable of handling ethernet-phy-ieee802.3-c45
PHYs correctly, and also does not handle MDIO bus wide reset-gpios property.
Until proper C45 PHY support lands in U-Boot, disable AVB1/AVB2 interfaces.
This only disables the two MACs with 88Q2110/88Q2112 100/1000BASE-T1 PHYs
on ethenet sub-board, the main board AVB0 ethernet is unaffected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In rzg2l_pinconf_set(), there are no new variables defined in the case
statement for PIN_CONFIG_INPUT_ENABLE so no additional scope is needed.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is be default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Ethenet interfaces on the Renesas RZ/G2L SoC family can operate at
multiple power supply voltages: 3.3V (default value), 2.5V and 1.8V.
rzg2l_pinconf_set() is extended to support the 2.5V setting, with a
check to ensure this is only used on Ethernet interfaces as it is not
supported on the SD & QSPI interfaces.
While we're modifying rzg2l_pinconf_set(), drop the unnecessary default
value for pwr_reg as it is set in every branch of the following if
condition.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
We can call dev_read_u32_default() instead of calling fdt_getprop() then
fdt32_to_cpu().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In the RZ/G2L family, core clocks are always on and can't be disabled.
However, drivers which are shared with other SoCs may call clk_enable()
or clk_enable_bulk() for a clock referenced in the device tree which
happens to be a core clock on the RZ/G2L. To avoid the need for
conditionals in these drivers, simply ignore attempts to enable a core
clock.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The env variable "SN" is used to store the serial number on DH electronics
SoMs. New SoMs will use the variable "dh_som_serial_number". To ensure
compatibility, these env variables are synchronized. This is achieved
using callback functions.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In case there are two variables which each implement env callback
that performs env_set() on the other variable, the callbacks will
call each other recursively until the stack runs out. Prevent such
a recursion from happening.
Example which triggers this behavior:
static int on_foo(...) { env_set("bar", 0); ... }
static int on_bar(...) { env_set("foo", 0); ... }
U_BOOT_ENV_CALLBACK(foo, on_foo);
U_BOOT_ENV_CALLBACK(bar, on_bar);
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Suggested-by: Marek Vasut <marex@denx.de>
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page, which
is populated with a structure containing ethernet MAC addresses, DH
item number and DH serial number.
Because the write-lockable page is not present on rev.100 i.MX8MP DHCOM
SoM, test whether EEPROM ID page exists by setting up the i2c driver.
There may be multiple EEPROMs with an ID page on this platform, always
use the first one. The evaluation of the EEPROM ID page is done in two
steps. First, the content is read and checked. This is done to cache
the content of the EEPROM ID page. Second, the content is extracted
from the EEPROM buffer by requesting it.
For the ethernet MAC address the i.MX8M Plus DHCOM currently supports
parsing address from multiple sources in the following priority order:
1) U-Boot environment 'ethaddr'/'eth1addr' environment variable
2) SoC OTP fuses
3) On-SoM EEPROM
Add support for parsing the content of this new EEPROM ID page and place
it between 2) and 3) on the priority list. The new entry is 2.5) On-SoM
EEPROM write-lockable page.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The new i.MX8M Plus DHCOM rev.200 is populated with M24C32-D EEPROM
that contains an additional write-lockable page called ID page. Add
aliases eeprom0wl and eeprom1wl for the access to the EEPROM ID
page node.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
iMX91 reuses iMX93 controller and PHY, but with lower speed,
so add new DDR rates for i.MX91.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add new rates to integer and frac PLL to support iMX91
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX91 is a derived from i.MX93, and most clocks could be reused from
i.MX93. Also Update imx93-clock.h to sync with linux next.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX91 is reduced part from iMX93 with part number: i.MX9131/11/01
It removed A55_1, M33, MIPI DSI, LVDS, etc.
i.MX9131:
- Support 2.4GT/s DDR and HWFFC at 1.2GT/s
i.MX9121:
- A55 at 800Mhz and DDR at 1600MTS, with low drive mode.
i.MX9111:
- Support 1.6GT/s DDR and HWFFC at 800MT/s
i.MX9101:
- Support 800Mhz ARM clock
- Support 1.6GT/s DDR and HWFFC at 800MT/s
- No parallel display, eQOS, flexcan
Updated Clock/Container/CPU and etc for i.MX91
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to iMX93 fuse burn plan, all 9x9 parts will have USB2,
ENET1 (FEC), LVDS1, CSI1 and DSI1 disabled. The codes missed ENET1
fuse when detecting 9x9. Although it still can detect 9x9 correctly,
we add the ENET1 fuse to the check to be more accurate.
Fixes: 58da865e27f ("imx9: add i.MX93 variants support")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace '#if DEBUG' with '#ifdef DEBUG', otherwise '#define DEBUG 1'
should be used and conflict with '#define DEBUG' in include/log.h
Fixes: 5fda95fb944 ("imx: imx9: Add TRDC driver for TRDC init")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
have_dual_base is set to false, so the 8ulp_data will be put in BSS
section which conflicts with the area of u-boot.dtb which padded just
after u-boot-nodtb.bin. So move 8ulp_data to data section to avoid
its content being corrupted by dtb.
Fixes: 51cfa66f2c4 ("gpio: imx_rgpio2p: support one address")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the environment into the board directory and convert header to a
txt file. In addition, this patch also applies following changes:
- Change default nfsroot path to /srv/nfs due to compliance with Linux
FHS 3.0.
- Rename specific variables as stated in the bootstd documentation.
Renamed variables:
fdt_addr => fdt_addr_r
fdt_file => fdtfile
Signed-off-by: Yunus Bas <y.bas@phytec.de>
