Judith Mendez <jm@ti.com> says:
This patch series adds config options for Sitara K3 boards
to support MMC UHS modes.
While testing with SD card boot and eMMC boot,
found missing eMMC boot support for am62ax in am62a7_init,
patch 1/7, and missing config option to support eMMC boot.
While we are here, for am62ax, enable config option to
change MMC bus modes and enable r5 SDHCI ADMA for faster boot
time.
Also for all k3 Sitara boards, cleanup MMC ENV configs that
are no longer needed since we no longer load env from MMC
device.
Link: https://lore.kernel.org/r/20241220203704.2076499-1-jm@ti.com
Fix spelling mistake in the board init files of j721e and j721s2.
s/WKUP_DEVSTAT_MCU_OMLY_MASK/WKUP_DEVSTAT_MCU_ONLY_MASK
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce get_boot_device() to obtain the booting device. Make it also
available for non SPL builds so u-boot can also know the device it
is booting from.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to greater than 7.
DDR intensive software applications can overwhelm the DSS's access to
the DDR because of their higher frequency DDR accesses. This can cause
flickering in display with certain applications running parallely if
the DSS traffic is being serviced through non-RT queue.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to greater than 7.
The C7x and VPAC can overwhelm the DSS's access to the DDR because of
their higher frequency DDR accesses. This can cause flickering in
display with certain edgeAI models running parallely if the DSS traffic
is being serviced through non-RT queue.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Bryan Brattlof <bb@ti.com> says:
Hello Everyone!
This small series converts TI's AM65x reference board to use
CONFIG_OF_UPSTREAM and removes the unused device tree files from
arch/arm/dts.
Because it's the last board using a AM65x without enabling OF_UPSTREAM
it allows us to also remove all the SoC FDT files as well and keep a
single version of the SoC's DT files in the dts/upstream directory going
forward.
Link: https://lore.kernel.org/r/20241121-am65x-v1-0-fe87aff1b5fc@ti.com
Rather than rely on manual updates from the arch/arm/dts directory,
enable CONFIG_OF_UPSTREAM to receive automatic device tree updates for
the am65x reference board.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Aniket Limaye <a-limaye@ti.com> says:
This series adds OPP_LOW spec data in k3_avs driver and enables a config
option to select the OPP_LOW performance point.
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
The default j7200 devicetree and k3_avs driver set OPP_NOM spec
frequency and voltage.
In the board init file, if K3_OPP_LOW config is enabled, Check if
OPP_LOW AVS voltage read from efuse is valid and update frequency (A72
and MSMC) and voltage (VDD_CPU) as per the OPP_LOW spec.
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
Test logs:
https://gist.github.com/aniket-l/328ad93ed60c2419ed7be9f85e6b6075
- With series applied on master and CONFIG_K3_OPP_LOW enabled in
j7200_evm_r5_defconfig
- Logs shown with and without efuse register programmed for OPP_0
(Errors out if OPP_0 not found, programs OPP_LOW spec if found)
- Voltage update verified using 'i2c md 0x4c 0xe' in u-boot
- Frequency update verified using 'k3conf clock dump' in linux
Link: https://lore.kernel.org/r/20241119003617.1871183-1-a-limaye@ti.com
Define new CONFIG_K3_OPP_LOW under arm/mach-k3/r5/Kconfig and add
default value to j7200_evm_r5_defconfig
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
The default j7200 devicetree and k3_avs driver set 2GHz/1GHz frequency
for A72/MSMC clks and the OPP_NOM voltage.
J7200 SOCs may support OPP_LOW Operating Performance Point:
1GHz/500MHz clks for A72/MSMC and OPP_LOW AVS voltage read from efuse.
Hence, add a config check in board_init_f() to select OPP_LOW specs:
- Check if OPP_LOW AVS voltage read from efuse is valid.
- Use the device IDs and clock IDs (TISCI docs [0]) to find the A72 and
MSMC clock frequencies in the devicetree.
- Fixup the clock frequencies in devicetree as per OPP_LOW spec.
k3_avs driver programs the OPP_LOW AVS voltage for VDD_CPU through
k3_avs_notify_freq() callback from clk_k3.
[0]: https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Introduce CONFIG_PHYTEC_K3_DDR_PATCH to make DDR timing patch code
optional for PHYTEC K3 boards. This allows better control over which
boards receive DDR timing patches, rather than compiling the code for
all boards with K3_DDRSS enabled.
Also enable the feature by default for PHYCORE_AM62X_R5.
Signed-off-by: Garrett Giordano <ggiordano@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Adaptive Voltage Scaling (AVS) Class 0 is a procedure for lowering the
voltage on certain device power rails. Initialize AVS Class 0.
Link: https://www.ti.com/lit/pdf/spruj28 (Section 5.2.3.3.2.5 AVS-Class0)
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Prasanth Babu Mantena <p-mantena@ti.com> says:
The channel allocation and deallocation for dma copy was happening on every
dma transfer. This is a overhead for transactions like NAND, which does
page reads recursively for complete data.
So, moving the dma allocation to probe and implement corresponding
remove function and cleanup dma device while exiting from spl.
Enable SPL_DM_DEVICE_REMOVE, for device removal capability in SPL.
Link: https://lore.kernel.org/r/20241009145703.1970034-1-p-mantena@ti.com
While exiting from spl, remove any dma device active through
spl_board_prepare_for_boot(). This is required for cleaning up
any dma channels being used in spl and avoid issues with overlapping
channel allocation in the next stage bootloaders.
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Add clk and device data which can be used by wkup_uart driver
to configure clocks and PSC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
AM62x devices now support CPU throttling based on thermal alerts
with a Linux commit 10e7bfd8114c ("arm64: dts: ti: k3-am62: Enable
CPU freq throttling on thermal alert"). However, this functionality
does not work correctly across all variants of the AM62x SoCs
which have different numbers of Cortex-A CPU cores: AM62x1 (1 core),
AM62x2 (2 cores), and AM62x4 (4 cores). On single-core and dual-core
AM62x devices, the following error is observed in the Linux kernel:
OF: /thermal-zones/main0-thermal/cooling-maps/map0: could not find
phandle 94
OF: /thermal-zones/main1-thermal/cooling-maps/map0: could not find
phandle 94
This commit adds a fixup to dynamically adjust the cooling-device
nodes in the thermal zones based on the actual number of CPU cores
available. This resolves the issue of CPU throttling not working
correctly on single-core and dual-core AM62x devices, while
maintaining the functionality for AM62x quad-core devices.
A similar approach is implemented for example on i.MX8MM SoC.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
The efi_add_known_memory() function for the TI K3 platforms is adding
the EFI_CONVENTIONAL_MEMORY type. This memory is now being handled
through the LMB module -- the lmb_add_memory() adds this memory to the
memory map. Remove the definition of the now superfluous
efi_add_known_memory() function.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chintan Vankar <c-vankar@ti.com> says:
This series enables Ethernet Boot on SK-AM62 device.
This series is based on commit 'f4f845b85926' of origin/next branch of
U-Boot.
Logs for Ethernet Boot for AM625-SK:
https://gist.github.com/chintanv133/464782796a9a60b9f5a49e674c5fc31a
In order to support Ethernet boot on AM62x, probe AM65 CPSW NUSS
driver in board_init_f().
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
We don't need a full word for this boolean value. Convert it into a flag
to save space in global_data.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
MCU_CLKOUT0 output can be driven by two different clock inputs:
one at 25 MHz and another at 50 MHz. Currently, the 25 MHz input
clock is not selectable due to a duplication of the 50 MHz clock input
in the mux configuration. This commit corrects the parent clock mux
configuration, making the 25 MHz input clock selectable.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to greater than 9.
Before setting up the QoS, the ORDERID needs to be mapped to VBUSM sources
using setup_navss_nb() function call that sets the threadmap for NBSS
registers. (Section 10.2.9.2.10 "Quality of Service" in TRM[0])
Section 3.2.1 "Quality of Service (QoS)" in the TRM[0] provide more
details.
[0]: https://www.ti.com/lit/zip/spruj52
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to greater than 9.
Before setting up the QoS, the ORDERID needs to be mapped to VBUSM sources
using setup_navss_nb() function call that sets the threadmap for NBSS
registers. (Section 10.2.9.2.10 "Quality of Service" in TRM[0])
Section 3.2.1 "Quality of Service (QoS)" in the TRM[0] provide more
details.
[0]: https://www.ti.com/lit/zip/spruj28
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to greater than 7.
Before setting up the QoS, the ORDERID needs to be mapped to VBUSM sources
using setup_navss_nb() function call that sets the threadmap for NBSS
registers. (Section 10.2.10.1.2 "NB Parameters" in TRM[0])
Section 3.3.2 "Quality of Service (QoS)" in the TRM[0] provide more
details.
[0]: https://www.ti.com/lit/zip/spruil1
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
For the QOS registers, instead of using the raw values for calculation
for each reg field, use a defined macro which takes in argument for all
the reg fields to get the desired value.
Do the similar simplification for QOS register and group registers and
make the corresponding changes for am62a_qos_uboot file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
QoS bit mapping are common across all K3 SoCs so move those defines
to common header file (k3_qos.h).
This ensures that we do not define these for each SoC.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Introduce the basic functions and definitions needed to properly
initialize TI J722S family of SoCs.
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Include the clock and lpsc tree files needed for the wkup spl to
initialize the proper PLLs and power domains to boot the SoC.
Reviewed-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Include the part number for TI's j722s family of SoC
to identify it during boot.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Sort CONFIG_SOC* and K3_SOC_ID alphabetically.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Wadim Egorov <w.egorov@phytec.de> says:
Changes in v2:
- Reabse to current next
- Add Tested-by: John Ma <jma@phytec.com>
- Add Kconfig option to select RAM size statically
- Make board/phytec/common/k3 always compile for CONFIG_ARCH_K3
v1: https://lists.denx.de/pipermail/u-boot/2024-May/553057.html
Call do_board_detect() hook before the K3 DDRSS driver gets probed.
It will allow boards to adjust DDR timings in do_board_detect().
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: John Ma <jma@phytec.com>
The flag will be used for booting authenticated remote procs from hs-se
devices which can optionally be used in hs-fs devices also.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ti_secure_image_post_process and ti_secure_image_check_binary is used
for the authentication purposes in the current boot flow. Authentication
of remoteproc firmware images require ti_secure_image_post_process to be
available outside mach-k3.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The address we load TFA and OPTEE is configurable by the
CONFIG_K3_{ATF,OPTEE)_LOAD_ADDR, but the DT node reservations remain
static which can cause some confusion about where exactly these firmware
are exactly. Fix this by updating the reserved-memory{} nodes when the
loaded address does not match the address in DT.
Reported-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
