The ethernet0_rmii_pins_a pinmux change has no effect on any
DHSOM based hardware. The mco2_pins_a and mco2_sleep_pins_a
are both part of stm32mp15-pinctrl.dtsi . Drop both pinmux
changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove unused local DT copies after the OF_UPSTREAM conversion.
Fixes: cccb29fc1270 ("ARM: dts: stm32: Switch to using upstream DT on DH STM32 DHSOM")
Reported-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In previous version of pwm driver, the polarity of pwm were implemented
in reverse. In recent release, that issue in the driver is fixed,
therefore, correctly set the polarity in the device tree.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3e8e38b77101335f86bca0f05b3988877bb12993.1729766551.git.michal.simek@amd.com
Use RTC available in HW on Kria SOM without using emulation that's why
configure it properly and disable emulated one.
Power on reset value of RTC Calibration register without battery backup is
not matching with crystal frequency which leads to RTC time drift. That's
why write CALIB_WRITE register with crystal frequency (0x7FFF). There is
also an option to write zero so that Linux will set default value (0x7FFF)
in driver probe but calibration 0 is not permited by DT schema.
Co-developed-by: Srinivas Goud <srinivas.goud@amd.com>
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9b684faeec85381b9b8fe796aaebc2ee79f17b8e.1729663761.git.michal.simek@amd.com
If TPL_GPIO and TPL_PINCTRL_ROCKCHIP are enabled and a sysreset-gpio is
provided in the TPL Device Tree, this will trigger a system reset
similar to what's currently been done in SPL whenever the RK3399 "warm"
boots. Because there's currently only one user of sysreset-gpio logic,
and TPL is enabled on that board, so let's migrate the logic and that
board to do it in TPL.
There are three reasons for moving this earlier:
- faster boot time as we don't need to reach SPL to be able to reset the
system on a condition we know is already met in TPL,
- have less code to be impacted by the issue this system reset works
around (that is, "unclean" SoC registers after a reboot),
- less confusion around the reason for restarting. Indeed when done from
SPL, the following log can be observed:
"""
U-Boot TPL 2025.01-rc1-00165-gd79216ca9878-dirty (Nov 05 2024 - 15:31:45)
Channel 0: DDR3, 666MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
Channel 1: DDR3, 666MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
256B stride
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2025.01-rc1-00165-gd79216ca9878-dirty (Nov 05 2024 - 15:31:45 +0100)
Trying to boot from MMC2
U-Boot TPL 2025.01-rc1-00165-gd79216ca9878-dirty (Nov 05 2024 - 15:31:45)
"""
possibly hinting at an issue within the SPL when loading the fitImage
from MMC2 instead of the normal course of events (a system reset).
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This defines a weak tpl_board_init function that can be used for running
board/SoC-specific code before the DRAM init happens, similarly to
spl_board_init() for SPL.
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prepare to support forcing power on reset from TPL which would have
the exact same logic, just in an earlier stage, let's merge the CRU
check that triggers the power on reset with the rest of the logic.
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The FriendlyElec NanoPi R2S Plus is a single-board computer based on
Rockchip RK3328 SoC. It features e.g. 1 GB DDR4 RAM, 32 GB eMMC,
SD-card, 2x GbE LAN, optional M.2 SDIO Wi-Fi and 2x USB 2.0 host.
Features tested on a NanoPi R2S Plus 2309:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Cool Pi GenBook, it works as a carrier board
connect with CM5 SOM.
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
Tested by Armbian boot on USB disk.
Change-Id: I4d9b8572dc7c400077dde666633f3fea1b47dd03
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For upstream Linux kernel we use below DTBs for HiHope boards:
- r8a774a1-hihope-rzg2m-ex.dtb
- r8a774e1-hihope-rzg2h-ex.dtb
- r8a774b1-hihope-rzg2n-ex.dtb
Update the CONFIG_OF_LIST to match the above. Now that we have switched
upstream DTS, drop deleting the nodes and also rename the
r8a774*-u-boot.dtsi files to r8a774*-ex-u-boot.dtsi to match the OF_LIST
files so that the `bootph-all` property gets applied to required nodes
in upstream DTS.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
When support for the Renesas RZ/G2L SoC was added, the GICR base address
for CPU1 was accidentally used. We should instead supply the GICR base
address for CPU0 so that interrupts are correctly configured for the
CPU core that U-Boot is actually using.
Fixes: 387d4275ab0e ("arm: rmobile: Add basic RZ/G2L family support")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
We are now using the dts/upstream subtree for the RZ/G2L SoC family so
we can drop unused devicetree files from arch/arm/dts.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/23262
- Improve imx9 boot medium autodection.
- Add possibility to skip DCD on i.MX8.
- Switch to using upstream DT on DH i.MX6 DHCOM.
- Add support for i.MX6DL DHCOM SoM on PDK2 carrier board.
- Handle FIELD_RETURN on i.MX HAB.
Working with HAB on the i.MX8MP we've encountered a case where a board
that successfully authenticates u-boot when booting Linux subsequently
fails to properly bring up the RTC.
The RTC registers live in the low-power block of the Secure Non-Volatile
Storage (SNVS) block.
The root cause of the error has been traced to the HAB handing off the
SNVS-RTC in a state where HPCOMR::NPSWA_EN = 0 in other words where the
Non-Privileged Software Access Enable bit is zero.
Configure SNVS to allow unpriv access to SNVS LP for imx8m and imx8mp.
This commit generalizes 723f8359c1 ("imx: mx7: snvs: Add an SNVS init
routine") to also be used on i.MX8M SoCs, and was testeed on i.MX8MP.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Commit 723f8359c1 ("imx: mx7: snvs: Add an SNVS init routine") noted
that the init_snvs() call likely applies to other i.MX processors, and
this has been found to be true for i.MX8MP.
Move snvs module for future re-use.
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Enable OF_UPSTREAM to use upstream DT and add nxp/imx/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Signed-off-by: Marek Vasut <marex@denx.de>
Improve "mmcautodetect=yes" boot mode autodetection to able to use it
if CONFIG_ENV_IS_NOWHERE=y is used for i.MX9 SoCs and i.MX93 EVK board.
If both CONFIG_ENV_IS_IN_MMC=y and CONFIG_ENV_IS_NOWHERE=y are in the
defconfig, CONFIG_ENV_IS_IN_MMC=y will be overiden default
CONFIG_ENV_IS_NOWHERE settings.
Goal is in this patch to able to use the boot mode autodetection
if defconfig use only CONFIG_ENV_IS_NOWHERE=y option
(without CONFIG_ENV_IS_IN_MMC) for any i.MX9 SoC.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
The decision on whether HAB is enabled is solely based on the SEC_CONFIG
fuse. The HAB FIELD_RETURN feature is able to permanently disable HAB on
a CPU, after which it is able to boot unsigned firmware. U-Boot however
does not take into account the FIELD_RETURN mode, and refuses to boot
unsigned software when the feature is enabled.
Also take the FIELD_RETURN fuse into account when deciding whether HAB
is enabled. When The FIELD_RETURN fuse is blown, HAB is not enabled.
Tested on i.MX8M Mini, i.MX8M Plus, i.MX8M Nano and i.MX6ULL
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
The imx_sec_config_fuse_t structure is not specific to the sec_config
fuse, but can be used for all fuse words.
Rename the structure to a more generic name to be reused for other
fuses.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
This is not implemented so cannot actually be used to read blocks.
Disable it until it is implemented, to avoid causing a hang with EFI,
which probes every available BLK device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Issue: https://source.denx.de/u-boot/u-boot/-/issues/37
Create a new disk for use with tests, which contains the new 'testapp'
EFI app specifically intended for testing the EFI loader.
Attach it to the USB device, since most testing is currently done with
mmc.
Initially this image will be used to test the EFI bootmeth.
Fix a stale comment in prep_mmc_bootdev() while we are here.
For now this uses sudo and a compressed fallback file, like all the
other bootstd tests. Once this series is in, the patch which moves
this to use user-space tools will be cleaned up and re-submitted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox is its own architecture, but sometimes we want to mimic the host
architecture, e.g. when running an EFI app not built by U-Boot.
Add a -N/--native flag which tells sandbox to reflect the architecture
of the host.
Signed-off-by: Simon Glass <sjg@chromium.org>
The commit 7576ab2facae ("riscv: Add support for AMD/Xilinx MicroBlaze V")
added support for 32bit version. 64bit version is also available that's why
wire it up too.
DT is providing description for generic QEMU target.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Commit 136b7b6d2e98 ("Subtree merge tag 'v6.11-dts' of dts repo [1] into
dts/upstream") updates the upstream dts for E850-96 board, bringing
upstream TRNG node. There is no need to keep TRNG node in appended dts
anymore, so remove it.
Tested on E850-96 board by running 'rng' command in U-Boot shell.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Leo Yan <leo.yan@arm.com> says:
This patch series is to refine the booting on Arm Total Compuate
platform.
It changes to use the info passed in DTB for initialization DRAM info,
and dynamically initializes the booting envoironment variables.
Another big change is to use an envoironment file for boot commands,
based on it, the series extends to support multiple block devices
(MMC and virtio). And the env file is extended for booting Debian.
The last commit is to update memory mapping info based on the DRAM info
passed via DT binding.
Link: https://lore.kernel.org/r/20241025171821.624702-1-leo.yan@arm.com
Initialize the environment variables 'fdt_addr_r' and 'kernel_addr_r'
during the misc init phase. The static configurations are not needed,
remove them.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
On Total Compute, TF-A passes the info via DT binding for the hardware
description - includes the serial, memory, and arm_ffa nodes.
This commit initializes the fdt base address based on the passed the
register x1.
The similar implementation has already been done for the raspberry pi,
so borrow a lot of it.
Co-developed-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com>
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
This is mostly hidden in the background, but it is sometimes useful to
look at it. Add a function to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create an SoC R5 dtsi file that could be used at board level R5 files. This
would help in keeping the SoC level changes in sync across board files.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Bastien Curutchet <bastien.curutchet@bootlin.com> says:
Hi all,
This patch series aims to add DM support for the AEMIF controller that
can be found in the DaVinci SoCs.
This controller has already a driver used by the Keystone SoCs so I
add my work to it.
As we can now easily import Linux device-trees, I try to stick the
most I can to the Linux bindings of the AEMIF controller. To do so I add
an 'intermediate' driver called 'ti-aemif-cs'. It's in charge of
configuring timings for a given chip select of the AEMIF controller.
Link: https://lore.kernel.org/r/20241021151330.1860929-1-bastien.curutchet@bootlin.com
AEMIF controller is present on other SoCs than the Keystone ones.
Remove Keystone specificities from the driver to be able to use it from
other architectures.
Adapt the ks2_evm/board.c to fit the new driver.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, a number of generic cache related functions have their common
prototype declared in include/cpu_func.h. Move the current set of
noncached functions there as well to match.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet (through eQOS interface)
- SD-Card
- UART console
The device tree file is taken from upstream Linux Kernel
through OF_UPSTREAM
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jan Kiszka <jan.kiszka@siemens.com> says:
This adds support for the new IOT2050 SM variant, introduces a sysinfo
driver which also permits SMBIOS support and switches the board to
OF_UPSTREAM. There are some further fixes for the boards included as well.
Not yet included is configuration support for DMA isolation via the PVU as
this depends on not yet merged DT bindings and another overlay.
[trini: This is just the first 10 patches in the series for now]
Link: https://lore.kernel.org/r/cover.1729577070.git.jan.kiszka@siemens.com
Main differences between the new variant and Advanced PG2:
1. Arduino interface is removed. Instead, an new ASIC is added for
communicating with PLC 1200 signal modules.
2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is
available.
3. DP interface is tailored down. Instead, to communicate with the
PLC 1200 signal modules, a USB 3.0 type B connector is added but the
signal is not USB.
4. DDR size is increased to 4 GB.
5. Two sensors are added, one tilt sensor and one light sensor.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: rebased over OF_UPSTREAM]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The U-Boot copy of the mpfs devicetree has, in general, been neglected
somewhat in comparison to the one in Linux. Moving to OF_UPSTREAM to
keep both in sync should serve to eliminate that discrepancy.
Additionally, moving to OF_UPSTREAM will let U-Boot automatically pick
up the devicetree rework that is in progress at [1].
Link: https://lore.kernel.org/all/20241002-private-unequal-33cfa6101338@spud/ [1]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
If we take an exception before u-boot is relocated, there's a good
chance we will end up in an endless loop of exceptions because resume is
invalid until after relocation.
Signed-off-by: Anton Blanchard <antonb@tenstorrent.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Align U-Boot with QEMU amd-microblaze-v-virt platform to be able to wire
it with CI.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Padmarao Begari <padmarao.begari@amd.com>
This requires some tweaking of the defconfig and
board_fit_config_name_match so that the new sources are taken into
account.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
We can simply use the default DT, Basic PG1, because no nodes that are
different between the variants play a role for SPL. Will help with the
migration to OF_UPSTREAM.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
