U-Boot is not picking boot.scr script address from device tree
rather it's using default address for Microblaze platform,
and it's picking for other platforms. Remove conditional check
for Microblaze platform, so that u-boot pick up boot.scr script
address for all platforms from device tree.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20240913093231.2343528-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Set NIDEN, enabling non-invasive debug for the CCI-400 PMU. Otherwise,
the PMU is effectively disabled.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240905171833.325548-3-sean.anderson@linux.dev
Signed-off-by: Michal Simek <michal.simek@amd.com>
Included the SPI header to resolve the no previous prototypes
for function. Removed unused mode variable.
sparse warnings
warning: no previous prototype for 'spi_get_env_dev'
[-Wmissing-prototypes]
warning: variable 'mode' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Link: https://lore.kernel.org/r/20240905115758.999936-1-prasad.kummari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for the Comvetia i.MX6Q LXR2 board, which is
uses the Phytec PFLA02 SoM.
Based on the original work from Stefano Babic <sbabic@denx.de>.
The Phytec PFLA02 devicetrees are taken from kernel 6.11-rc7.
The imx6q-lxr.dts has been submitted upstream:
https://lore.kernel.org/linux-devicetree/20240913200906.1753458-3-festevam@gmail.com/
After it gets accepted in mainline (most likely in kernel 6.13),
the lxr2 board can then be switched to OF_UPSTREAM and these device trees
can be removed from U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add back low drive mode 1866mts ddr timing file, no need
CONFIG_IMX9_LOW_DRIVE_MODE anymore, using runtime selection.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove unused CONFIG_IMX9_LOW_DRIVE_MODE kconfig and
imx93_11x11_evk_ld_defconfig.
Remove the ld timing file.
The LD mode support will be added back with runtime detection later.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. Use runtime voltage selection for LD/OD/ND mode.
2. According to latest PE/TE report, the voltages of VDD_SOC for
LD and ND mode need add 50mv margin, so LD voltage is 0.75v->0.8v,
ND voltage is 0.8v->0.85v.
3. Use TOFF_DEB to differentiate new trimmed pmic and old pmic
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since we use SPEED GRADE fuse to set A55 frequency, remove the
set_arm_core_low_drive_clk function which has hard coded frequency.
And adjust clock_init called sequence and split it to early and late
functions.
Set the authen register in early function, because CCF driver checks
NS bit.
Set bus and core clock in late function, because the fuse read and
SoC type/rev depend on ELE.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace the static CONFIG_IMX9_LOW_DRIVE_MODE with runtime target
voltage mode by checking the part's SPEED GRADE fuse.
SPL will configure to highest A55 speed which is indicated by the SPEED
fuse and select corresponding voltage mode.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If CONFIG_SYS_MEM_TOP_HIDE is defined, gd->ram_size is reduced by
CONFIG_SYS_MEM_TOP_HIDE. Need to correct the actual ram size in
dram_init_banksize.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
UEFI:
* Use generated UUIDs in UEFI capsules:
- efi: define struct efi_guid
- lib: uuid: add UUID v5 support
- efi: add a helper to generate dynamic UUIDs
- doc: uefi: document dynamic UUID generation
- sandbox: switch to dynamic UUIDs
- lib: uuid: supporting building as part of host tools
- include: export uuid.h
- tools: mkeficapsule: use u-boot UUID library
- tools: mkeficapsule: support generating dynamic GUIDs
- test: lib/uuid: add unit tests for dynamic UUIDs
- test: lib/uuid: add tests for UUID version/variant bits
* Minor code clean-up
- shorten efi_bootmgr_release_uridp_resource()
- rename efi_bootmgr_image_return_notify
- return the correct error in efi_bootmgr_release_uridp()
- Kconfig: clean up the efi configuration status
- Use puts() in cout so that console recording works
- Put back copyright message in helloworld.c
-----BEGIN PGP SIGNATURE-----
iQJWBAABCABAFiEEK7wKXt3/btL6/yA+hO4vgnE3U0sFAmbkQbQiHGhlaW5yaWNo
LnNjaHVjaGFyZHRAY2Fub25pY2FsLmNvbQAKCRCE7i+CcTdTS78AD/438lZrXSvV
0aunMCDokTlg7Hxwme1oeLI6+r1SFwJa2EHEdsKbZ74ubh8H/UJkyFpsPr5mZeCI
BUkrxiI3bJnsw8HftZpkc4k1fRgzk/ufNcH1ywyFLV5gXfAHUpPzfx3C3eB2unr3
f0zlsOl7VTkdOqXSebWcbFGXIKRb/p6jUtWkCaM/Ip3i8wgEU9PlFTPXutdxHFi/
GsByD7I2exsnoEm+ODZ1P/FGEyhWMAN8c643DWRplc8vFHFyg8rqsnjOOekWN4WO
HMVvs9lUKtLpWK8HaoAZKFL1NFdwdEjbaRUqSeHSdKan/tJIRgTNGzrtlD/i7YHQ
b2nTrlhlDtrobfITvyicg7cIy/XcBksIFOQ3kHaZWD18DINiwuX1AEKESwqdFGpB
88gaE45XAqTYW8EpSYq61JlaPQZvR70nXISzLCIce25a1jFt6oO88rV5eEHm67gA
HufIiyR2aOTiFvrHe0ZNgjeOMGMaFFHEMTOx+exhAJ6NTuwgWi/aTQXGF2OkWzBX
LXCnb6huyAOqj+3PJCCIed9vf2AlvIm7a8hZDxmCmJMWmaHrRIObBjLZOmGu9vU4
cdaMNO1s4bptqGjhfETxmjbtnX9YI8hAhChNs0d/vs1k0hIMPaI170Q9zR2xN+2S
wBG3iMs9Q6ECNaoeVcfwS2HfpVovI7j4uQ==
=mncs
-----END PGP SIGNATURE-----
Merge tag 'efi-next-20241024' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request efi-next-20241024
UEFI:
* Use generated UUIDs in UEFI capsules:
- efi: define struct efi_guid
- lib: uuid: add UUID v5 support
- efi: add a helper to generate dynamic UUIDs
- doc: uefi: document dynamic UUID generation
- sandbox: switch to dynamic UUIDs
- lib: uuid: supporting building as part of host tools
- include: export uuid.h
- tools: mkeficapsule: use u-boot UUID library
- tools: mkeficapsule: support generating dynamic GUIDs
- test: lib/uuid: add unit tests for dynamic UUIDs
- test: lib/uuid: add tests for UUID version/variant bits
* Minor code clean-up
- shorten efi_bootmgr_release_uridp_resource()
- rename efi_bootmgr_image_return_notify
- return the correct error in efi_bootmgr_release_uridp()
- Kconfig: clean up the efi configuration status
- Use puts() in cout so that console recording works
- Put back copyright message in helloworld.c
Move this header to include/u-boot/ so that it can be used by external
tools.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Migrate sandbox over to generating it's capsule update image GUIDs
dynamically from the namespace and board/image info. Update the
reference and tests to use the new GUIDs.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Define and parse the header of the First Mutable Code (FMC)
of AST2700 SoCs at runtime phase.
The FMC header contains the information to load prebuilt binaries
required for device initialization such as DRAM and VGA.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Daniel Schultz <d.schultz@phytec.de> says:
This patch stack extends the phyCORE-AM62x/AM64x U-Boot by following boot
sources:
- Load U-Boot with USB DFU
- Load a Linux and initramfs from OSPI/QSPI NOR flash
- Load a Linux and rootfs from Network
Moreover, it adds required changes to the environment to boot an A/B
system with RAUC and includes some minor fixes.
Include the boot logic to boot via Network or from a OSPI/QSPI
NOR flash. Moreover, set all required variables to both boot
methods to the environment.
Note: The phyBOARD-Electra AM64x is not able to load the U-Boot
via Network. However, it's still possible to load the kernel.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Include the boot logic to boot via Network or from a OSPI/QSPI
NOR flash. Moreover, set all required variables to both boot
methods to the environment.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The Kconfig symbols SYS_ARCH, SYS_CPU, SYS_SOC, SYS_VENDOR and
SYS_BOARD are defined in arch/Kconfig as having type string, and most
board files simply amend those definition with suitable
default "foo"
or
default "foo" if BAR
stanzas. But some also include a redundant repetition of the type.
Homogenize the code base by removing those lines.
Generated by
find arch/*/ board -name Kconfig | xargs perl -i -g -pe 's/(config SYS_(ARCH|CPU|SOC|VENDOR|BOARD)\n)\s*string\n/\1/gs'
with the trailing slash in arch/*/ ensuring that arch/Kconfig itself
is not found.
This does not change boards which add a prompt string, e.g.
string "Board name"
because I think those change the semantics of the symbol into being
user-settable.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
For the Milk-V Mars CM (lite) we have only been copying sizeof(void *)
bytes to the compatible property instead of the whole string list.
Fixes: de3229599d4f ("board: add support for Milk-V Mars CM")
Reported-by: E Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We already have some documentation describing how to enable debug UART
for Qualcomm SoCs. However the UART address varies per-soc... Add some
config fragments to enable debug UART for few well supported SoCs.
These can be used like:
$ make qcom_defconfig debug-sdm845.config
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Tim Harvey <tharvey@gateworks.com> says:
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
EXT_CSD_BOOT_ACK_ENABLE (1 << 6)
EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3)
EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0)
EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0)
EXT_CSD_BOOT_ACK(x) (x << 6)
EXT_CSD_BOOT_PART_NUM(x) (x << 3)
EXT_CSD_PARTITION_ACCESS(x) (x << 0)
EXT_CSD_EXTRACT_BOOT_ACK(x) (((x) >> 6) & 0x1)
EXT_CSD_EXTRACT_BOOT_PART(x) (((x) >> 3) & 0x7)
EXT_CSD_EXTRACT_PARTITION_ACCESS(x) ((x) & 0x7)
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field used by the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
Additionally provide arrays of the field names and allow those to be
used in the 'mmc partconf' command and in board support files.
The first patch adds enumerated types and makes use of them which
represents no compiled code change.
The 2nd patch adds the array of names and uses them in the 'mmc
partconf' command.
The 3rd patch uses the array of hardware partition names in a board
support file to show what emmc hardware partition U-Boot is being loaded
from.
To aid in understanding what emmc hardware partition is being
used to boot on power-up, display the hardware partition name in the
SPL.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field which is also the value used to specify the
hardware partition of the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
This represents no code changes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Sughosh Ganu <sughosh.ganu@linaro.org> says:
This is a follow-up from an earlier RFC series [1] for making the LMB
and EFI memory allocations work together. This is a non-rfc version
with only the LMB part of the patches, for making the LMB memory map
global and persistent.
This is part one of a set of patches which aim to have the LMB and EFI
memory allocations work together. This requires making the LMB memory
map global and persistent, instead of having local, caller specific
maps. This is being done keeping in mind the usage of LMB memory by
platforms where the same memory region can be used to load multiple
different images. What is not allowed is to overwrite memory that has
been allocated by the other module, currently the EFI memory
module. This is being achieved by introducing a new flag,
LMB_NOOVERWRITE, which represents memory which cannot be re-requested
once allocated.
The data structures (alloced lists) required for maintaining the LMB
map are initialised during board init. The LMB module is enabled by
default for the main U-Boot image, while it needs to be enabled for
SPL. This version also uses a stack implementation, as suggested by
Simon Glass to temporarily store the lmb structure instance which is
used during normal operation when running lmb tests. This does away
with the need to run the lmb tests separately.
The tests have been tweaked where needed because of these changes.
The second part of the patches, to be sent subsequently, would work on
having the EFI allocations work with the LMB API's.
[1] - https://lore.kernel.org/u-boot/20240704073544.670249-1-sughosh.ganu@linaro.org/T/#t
Notes:
1) These patches are on next, as the alist patches have been
applied to that branch.
2) I have tested the boot on the ST DK2 board, but it would be good to
get a T-b/R-b from the ST maintainers.
3) It will be good to test these changes on a PowerPC platform
(ideally an 85xx, as I do not have one).
The LMB memory is typically not needed very early in the platform's
boot. Do not add memory to the LMB map before relocation. Reservation
of common areas and adding of memory is done after relocation.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
With the introduction of separate config symbols for the SPL phase of
U-Boot, the condition checks need to be tweaked so that platforms that
enable the LMB module in SPL are also able to call the LMB API's. Use
the appropriate condition checks to achieve this.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current LMB API's for allocating and reserving memory use a
per-caller based memory view. Memory allocated by a caller can then be
overwritten by another caller. Make these allocations and reservations
persistent using the alloced list data structure.
Two alloced lists are declared -- one for the available(free) memory,
and one for the used memory. Once full, the list can then be extended
at runtime.
[sjg: Use a stack to store pointer of lmb struct when running lmb tests]
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
[sjg: Optimise the logic to add a region in lmb_add_region_flags()]
Users experiencing random kernel crashes due to new versions of
Marvell's DDR training algorithm can solve the issue by setting DDR
speed to 1333H.
But if kernel crashes, it has to be done in U-Boot, which is impossible
without UART connection.
In order to make it easier for users, use the rescue button mechanism:
when rescue mode 9 is selected (that is when 10 LEDs are ON), U-Boot
will train DDR in 1333H mode and also update EEPROM so that subsequent
boot will use this mode.
User has to use the `eeprom` command in U-Boot or `omnia-eeprom` command
in OS to switch back to 1600K mode.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the i2c_eeprom miscellaneous driver for reading Turris Omnia EEPROM
in U-Boot proper. Keep using dm_i2c_read() in SPL build, since adding
the i2c_eeprom driver to SPL build increases the image by 1.5 KiB.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename the variable holding the EEPROM udevice from `chip` to `eeprom`.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22211
- Enable SPI NOR flash support and MTD partitions for phycore_imx8mp.
- Convert mx6slevk to OF_UPSTREAM and watchdog DM.
- Cleanup some mx5/mx6 USB options.
- Make PLL settings configurable at board level.
- Set CONFIG_SPL_LOAD_FIT_ADDRESS for verdin-imx8m/p.
- Make the mxc-gpio reading state of GPIO pins in output mode to be
consistent with the Linux kernel.
- Add HUK derivation support for ELE AHAB.
Chintan Vankar <c-vankar@ti.com> says:
This series enables Ethernet Boot on SK-AM62 device.
This series is based on commit 'f4f845b85926' of origin/next branch of
U-Boot.
Logs for Ethernet Boot for AM625-SK:
https://gist.github.com/chintanv133/464782796a9a60b9f5a49e674c5fc31a
Depending on if a SPI-NOR flash is populated add the mtd partition
table to the device tree. For this we have to also probe the
flash before booting.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
We don't need a full word for this boolean value. Convert it into a flag
to save space in global_data.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The Data Modul i.MX8M Plus eDM SBC does have USB gadget capable port
accessible via USB A-A cable plugged into the bottom USB 3.0 port.
Use USB SDPS as the fallback boot device, so USB SDPS loading can
be performed using e.g. uuu tool.
Signed-off-by: Marek Vasut <marex@denx.de>
Added m7 core support in uboot for imx8mp by adding
the boot variable prepare_mcore.
Based on commit 0ed32cc8568a ("LF-6555 imx8m[m/n/p/q]_evk: add
bootargs to support mcore")
Signed-off-by: Yashwanth Varakala <y.varakala@phytec.de>
With DM_SERIAL in place, there is no need to setup the UART pins
in the board code.
The UART pins are setup via devicetree, thanks to DM.
Remove the unneeded code.
Signed-off-by: Fabio Estevam <festevam@denx.de>
CONFIG_DM_MMC and CONFIG_DM_SPI are alway selected so the mmc
and spi board code can be safely removed.
Remove it to make the code cleaner.
Signed-off-by: Fabio Estevam <festevam@denx.de>
With commit 922d4504bcab ("imx: scu_api: update to version 1.16 and
add more APIs") added the reboot API.
Add the board code to use that.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
