Upstream Linux commit f90b68d6c8b0.
The CORE/BUS root slice has following design, simplied graph:
The difference is core not have pre_div block.
A composite core/bus clk has 8 inputs for mux to select, saying clk[0-7].
It support target(smart) interface and normal interface. Target interface
is exported for programmer easy to configure ccm root. Normal interface
is also exported, but we not use it in our driver, because it will
introduce more complexity compared with target interface.
The normal interface simplified as below:
SEL_A GA
+--+ +-+
| +->+ +------+
CLK[0-7]--->+ | +-+ |
| | | +----v---+ +----+
| +--+ |pre_diva+----> | +---------+
| +--------+ |mux +--+post_div |
| +--+ |pre_divb+--->+ | +---------+
| | | +----^---+ +----+
+--->+ | +-+ |
| +->+ +------+
+--+ +-+
SEL_B GB
The mux in the upper pic is not the target interface MUX, target
interface MUX is hiding SEL_A and SEL_B. When you choose clk[0-7],
you are actually writing SEL_A or SEL_B depends on the internal
counter which will also control the internal "mux".
The target interface simplified as below which is used by Linux Kernel:
CLK[0-7]--->MUX-->Gate-->pre_div-->post_div
A requirement of the Target Interface's software is that the
target clock source is active, it means when setting SEL_A, the
current input clk to SEL_A must be active, same to SEL_B.
We touch target interface, but hardware logic actually also need
configure normal interface.
There will be system hang, when doing the following steps:
The initial state:
SEL_A/SEL_B are both sourcing from clk0, the internal counter
choose SEL_A.
1. switch mux from clk0 to clk1
The hardware logic will choose SEL_B and configure SEL_B to clk1.
SEL_A no changed.
2. gate off clk0
Disable clk0, then the input to SEL_A is off.
3. switch from clk1 to clk2
The hardware logic will choose SEL_A and configure SEL_A to clk2,
however the current SEL_A input clk0 is off, the system hang.
The solution to fix the issue is in step 1, write twice to
target interface MUX, it will make SEL_A/SEL_B both sources
from clk1, then no need to care about the state of clk0. And
finally system performs well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The mux flags (u8), div flags (u8), and gate flags (u8) are not the clk
flags (unsigned long). They have different meanings
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The mux flags (u8), div flags (u8), and gate flags (u8) are not the clk
flags (unsigned long). They have different meanings
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for PCIe clocks required to enable PCIe support on
iMX8MM SoC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for PCIe clocks required to enable PCIe support on
iMX8MP SoC.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice*
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since commit cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
the apalis-imx8qm board no longer boots.
The reason is that the imx8qm clock driver does not handle the
LPUART IPG clocks inside get_rate(), set_rate() and enable() functions.
Fix the boot regression by adding the LPUART IPG entries.
Fixes: cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
the colibri-imx8qxp board no longer boots.
The reason is that the imx8qxp clock driver does not handle the
LPUART IPG clocks inside get_rate(), set_rate() and enable() functions.
Fix the boot regression by adding the LPUART IPG entries.
Fixes: cc7df0b9e8bc ("serial: lpuart: Enable IPG clock")
Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Colibri iMX8X
Acked-by: Sean Anderson <seanga2@gmail.com>
Switch to using new dump operation in clock provider drivers instead of
overriding soc_clk_dump.
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Link: https://lore.kernel.org/r/20231109105516.24892-8-ivprusov@sberdevices.ru
Based on Linux kernel 6.7-rc4, add necessary clocks for the PWM
controllers.
Signed-off-by: Nicolas Heemeryck <nicolas.heemeryck@devialet.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX93 CCF driver support.
Modifed from Linux Kernel v6.5-rc2 and adapted for U-Boot.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are some newer clocks added to the kernel recently,
so to fix prepare for resycing the device trees, update
the clock list. Since there are some minor changes to
the USB clocks, update which USB clocks are enabled
to match with the upstream kernel as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add clock for the DWMAC EQoS block. This is used among other things
to configure the MII clock via DM CLK.
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
[backport from linux commit bedcf9d1dcf88ed38731f0ac9620e5a421e1e9d6]
Unlike audio_pll1 and audio_pll2, there is no video_pll2. Further, the
name used in the RM is video_pll. So, let's rename "video_pll1" to
"video_pll" to be consistent with the RM and avoid misunderstandings.
No functional changes intended.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20221219113127.528282-3-dario.binacchi@amarulasolutions.com
[backport from linux commit a429c60baefd95ab43a2ce7f25d5b2d7a2e431df]
The IMX8MN platform does not have any video processing unit (VPU), and
indeed in the reference manual (document IMX8MNRM Rev 2, 07/2022) there
is no occurrence of its pll. From an analysis of the code and the RM
itself, I think vpu pll is used instead of m7 alternate pll, probably
for copy and paste of code taken from modules of similar architectures.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20221219113127.528282-2-dario.binacchi@amarulasolutions.com
This converts 7 usages of this option to the non-SPL form, since there is
no SPL_CMD_CLK defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the
QSPI clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the
ecspi clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock
inside the non-SPL block to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
PWM is not used inside SPL, so do not define the PWM clocks inside
SPL to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add gpmi nand clock. Those clock can be used in mxs nand driver
to run nand to EDO mode 5, 4, ...
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add shared counter in order to avoid to swich off clock that
are already used.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The i.MXRT11 series has two new pll types but are variants of existing.
This patch adds the ability to read one of the pll types' frequency
as it can't be changed unlike the generic pll it also has the
division factors swapped.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Upstream commit 7a2c3be95a50 ("clk: imx8mp: Fill in DWC3 USB, USB PHY,
HSIOMIX clock") added usb_core_ref for USB Controller but never set it
to be used as a clock source, using rather "osc_32k" instead.
This produces following boot log message:
"clk_register: failed to get osc_32k device (parent of usb_root_clk)"
Fix the USB controller clock source by using usb_core_ref instead of
osc_32k.
Fixes: 7a2c3be95a50 ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Root clock name contained underscore, which does not match to the actual
clock name.
Correct the name to match what is present in the FDT.
Fixes: 87f958810fcb ("clk: imx8mp: Add ECSPI clocks")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fix registration of 24M and 32k clock, those got applied or rebased
incorrectly, so fill in the correct code.
Fixes: 7a2c3be95a5 ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Add clock tables required to bring up DWC3 USB, USB PHY and HSIOMIX domain.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Re-factor the imx8m[nmpq] rate tables into the common pll1416x clock
driver.
43cdaa1567ad3 ("clk: imx8mm: Move 1443X/1416X PLL clock structure to common place")
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
This is a DM clock driver based off the imx8mm u-boot driver and the linux
kernel driver.
All of the PLLs and clocks are initialized so the subsystems below are
functional and tested.
1) USB host and peripheral
2) ECSPI
3) UART
4) I2C all busses
5) USDHC for eMMC support
6) USB storage
7) GPIO
8) DRAM
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Acked-by: Sean Anderson <seanga2@gmail.com>
This converts most CCF drivers to use generic ops. imx6q is the only
outlier, where we retain the existing functionality by moving the check to
request().
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220320203446.740178-2-seanga2@gmail.com
[ fixed missing include for at91 ]
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The clock composite is required when using the clock framework. So
select it automatically.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
At present some drivers use -ENOSUPP to indicate that an unknown or
unsupported clock is used. Most use -EINVAL, indicating an invalid value,
so convert everything to that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
