Remove unused CONFIG_IMX9_LOW_DRIVE_MODE kconfig and
imx93_11x11_evk_ld_defconfig.
Remove the ld timing file.
The LD mode support will be added back with runtime detection later.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add trdc_mbc_blk_num to get num blks in a MBC mem slot, then drop
the hardcoded value '40' for NIC OCRAM configuration.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8M and i.MX9 have duplicated fixup_thermal_trips, so move it
to arch/arm/mach-imx/fdt.c to avoid duplicated code.
The critial temperature point for i.MX9 set to "maxc - 5" back to give
some margin.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for iMX93 low performance parts 9302 and 9301 which
restrict to low drive voltage only.
The parts run A55 max speed at 900Mhz and M33 at 133Mhz, have NPU
and A55 core1 (9301) disabled.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support 1.866GTS LPDDR4x timing script, need to add 233Mhz freq
to DDR PLL for second mission point at 933MTS. Otherwise DDR training
will fail.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Normally, the wdog will be used for trigger external PMIC reset
through the WDOG_ANY pin. If the PMIC chip has debounce logic for
the reset signal, in some corner case the wdog can NOT trigger
external PMIC reset if the SoC has been reset internal before the
PMIC captures the WDOG_ANY pin reset, so need to keep the WDOG3-5
reset masked in the SRC to let the PMIC to do the reset safely.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since we use SPEED GRADE fuse to set A55 frequency, remove the
set_arm_core_low_drive_clk function which has hard coded frequency.
And adjust clock_init called sequence and split it to early and late
functions.
Set the authen register in early function, because CCF driver checks
NS bit.
Set bus and core clock in late function, because the fuse read and
SoC type/rev depend on ELE.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace the static CONFIG_IMX9_LOW_DRIVE_MODE with runtime target
voltage mode by checking the part's SPEED GRADE fuse.
SPL will configure to highest A55 speed which is indicated by the SPEED
fuse and select corresponding voltage mode.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The boot image includes Edgelock Enclave(ELE) Firmware. Print the
information out to let user know which version firmware is being used.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The second Ethernet MAC (eQOS) fuse layout is changed since i.MX93 A1
following other i.MX platforms, for example i.MX8MP.
Order for A0:
MAC1_ADDR[15:0]
MAC1_ADDR[31:16]
MAC1_ADDR[47:32]
MAC2_ADDR[47:32]
MAC2_ADDR[15:0]
MAC2_ADDR[31:16]
Order since A1:
MAC1_ADDR[15:0]
MAC1_ADDR[31:16]
MAC1_ADDR[47:32]
MAC2_ADDR[15:0]
MAC2_ADDR[31:16]
MAC2_ADDR[47:32]
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support OSCCA enabled part which has disabled FSB access from SOC,
change directly read from FSB to use fuse_read API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Print UID in big endian format and as one buffer of bytes, so customer
can directly use it for EdgeLock 2GO.
Before:
UID: 0xf6c8ae93 0x0f46b326 0x10d61eb3 0x0583c2d2
Become:
UID: 93aec8f626b3460fb31ed610d2c28305
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
ROM use UID[0] and UID[1] as serial number with big endian when usb serial
download.
After update this, uuu(>1.6) can use below command to filter out devices
when multi boards connected.
uuu -ms <serial#> ...
[sudo] uuu -lsusb can list known devices with serial# informaiton.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On OSCCA part, M33 TCM is used for ROM PATCH and protected by ELE ROM.
So after release TRDC, we need to configure TRDC for M33 TCM,
otherwise A55 can't access the TCM.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
SSAR handshake done means power on finished, not ISO done. so correct
the waiting mask.
Fixes: 0256577a83b ("imx: imx9: Add MIX power init")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-imx, CPU specific sub-directories and
include/asm/arch-mx* files and when needed add missing include files
directly.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This event callback imx9_probe_mu needs to be called in board_r
as well, because many ELE APIs depending on this MU probed
Signed-off-by: Ye Li <ye.li@nxp.com>
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Commit d5eae216d833 ("net: dwc_eth_qos: Add board_interface_eth_init()
for i.MX93") implemented board_interface_eth_init for i.MX9 platforms.
However it only accounted for the EQOS interface while any board using
FEC as primary Ethernet interface was left out as return value -EINVAL
is always returned from the function in such case.
Fix this by returning 0 (success) when FEC interface is primarily used
instead of EQOS interface on i.MX93.
Fixes: d5eae216d833 ("net: dwc_eth_qos: Add board_interface_eth_init() for i.MX93")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Tested-by: Mathieu Othacehe <m.othacehe@gmail.com>
Read i.MX9 CPU temp grade from fuses and fixup thermal trips in Linux
device-tree accordingly.
Based on commit 0543a1ed2787 ("imx8m: fixup thermal trips")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
All i.MX93 targets rely on using binman to generate the U-Boot
binary.
Select it at the SoC level instead of per board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Removed fdt_addr from verdin-imx8mm to fix booting via bootefi.
- Support Ethernet PHY autodection on Data Modul i.MX8M Mini/Plus eDM
SBC
- Add i.MX93 binman support
- Add support for imx93-var-som
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add dedicated Makefile targets for the i.MX93 and a new imx93-u-boot.dtsi
device-tree to create binman images.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add a common board_interface_eth_init() called by the DWC MAC driver to
setup the MAC <-> PHY interface according to the PHY mode obtained from
DT.
Remove the board-side configuration in the i.MX93 EVK files.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
If dram_init_banksize() is called from SPL, the rom_pointer, at that
point, is not correctly initialized. This causes wrong calculation of
DRAM start and size in dram_init_banksize(). The issue became apparent
only in Falcon Mode. Added an extra condition to prevent using
rom_pointer in SPL.
Signed-off-by: Elena Popa <elena.popa@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Very few of the existing event-spy records use the arguments they are
passed. Update them to use a simple spy instead, to simplify the code.
Where an adaptor function is currently used, remove it where possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.
This solution is based on (with added SPL support):
Link: https://lore.kernel.org/all/20211020191626.3648540-1-ricardo@foundries.io/
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
