Enable SPL and binman to generate u-boot.img (machine mode) and u-boot.itb
(supervisor mode). DTB is placed at fixed address to ensure that it is 8
byte aligned which is not ensured when dtb is attached behind SPL binary
that's why SPL and U-Boot are taking DTB from the same address.
Also align addresses for both defconfigs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/85506bce5580d448f095f267d029e3932c5e9990.1707911544.git.michal.simek@amd.com
Although there were still some variations in board DTS files based on
meson-gxbb SoC but I think those were minor differences from upstream
and shouldn't impact boot on these devices.
So enable OF_UPSTREAM to use upstream DT and add amlogic/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
With the SYSRESET subsystem enabled we do not need to implement
reset_cpu() in the board directory.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable the appropriate PMIC driver as well as the `pmic` command.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver supports the I2C module on the Renesas RZ/G2L (R9A07G044)
SoC, also known as the RIIC module.
This patch is based on both the u-boot driver in the Renesas RZ BSP
3.0.5 release [1] (commit 7fcc1fdc2534), and the Linux v6.7 driver
(commit 0dd3ee311255).
Support for deblocking the I2C bus is included as this may be needed
after triggering a reset via the Power Management IC (PMIC) over I2C
(the PMIC asserts the reset line before the SoC completes the I2C write
transaction with obvious bus locking effects). If the SDA line is
observed to be low during initialisation, we automatically attempt to
deblock.
[1]: https://github.com/renesas-rz/renesas-u-boot-cip
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for booting the imxrt1050-evk from spi.
Add imximage config and the ability for SPL to boot from NOR.
Enable binman in Kconfig and device tree for imxrt* as it is used to
prepend fspi_header.bin to SPL and u-boot.img.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
When booting Android with AVB enabled, an OOM is observed:
=> avb init ${mmcdev}
=> avb verify _a
## Android Verified Boot 2.0 version 1.1.0
read_is_device_unlocked not supported yet
read_rollback_index not supported yet
avb_util.c:182: ERROR: Failed to allocate memory.
OOM error occurred during verification
A custom malloc length of 128MB is required as documented in
commit 285a83b12bdf ("configs: meson64_android: increase SYS_MALLOC_LEN to 128M for AVB")
However, this 128M custom malloc length was not ported to Kconfig in
commit 7cfbba36e9f8 ("Convert CONFIG_SYS_MALLOC_LEN to Kconfig")
Add it back to fix AVB verification on VIM3/VIM3L.
Fixes: 7cfbba36e9f8 ("Convert CONFIG_SYS_MALLOC_LEN to Kconfig")
Co-developed-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Link: https://lore.kernel.org/r/20240209-vim3-avb-malloc-v1-1-91427d8c19ab@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Nishanth Menon <nm@ti.com> says:
This is a wide cleanup to switch to setting fdtfile using env_set
instead of scripted magic. 'fdtfile' is expected to be set by default.
This allows the stdboot triggered efi loaders to find the correct OS
device tree file even if regular boot process is interrupted by user
intervention.
Stop using the findfdt script and switch to setting the fdtfile from C
code.
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Stop using the findfdt script and switch to setting the fdtfile from C
code.
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Stop using the findfdt script and switch to setting the fdtfile from
C code.
While at this, replace findfdt in environment with a warning as it is
no longer needed
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Stop using the findfdt script and switch to setting the fdtfile from
C code.
While at this, replace findfdt in environment with a warning as it is
no longer needed
Reviewed-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
The Sielaff i.MX6 Solo board is a control and HMI board for vending
machines. Add support for this board.
The devicetree files are taken from pending changes in the Linux
kernel that are available from linux-next and will likely be
part of Linux v6.9.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
There is no imx8mp-msc-sm2s.dtb file in upstream Linux.
Change it to imx8mp-msc-sm2s-ep1.dtb.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Redundant environment support is required for software updates.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Currently, the Ethernet ports are not working.
The Ethernet PHY reset lines are controlled by the TCA6424 I2C GPIO
expander.
The TCA6424 I2C GPIO expander is supported by the CONFIG_DM_PCA953X
driver.
Select the CONFIG_DM_PCA953X option so that the Ethernet PHYs can
go through a proper reset making Ethernet to be functional.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
The conversion to DM_SERIAL is mandatory, so do the conversion.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
These systems are unlikely to use EFI as this functionality has not been
enabled until it got pulled in by Kconfig default. This functionality
does add some 60-70 kiB to the u-boot.img size, which overflows the size
limit. Disable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Adding a tiny bit more code for mini u-boot leads to a OCM
image overflow. Fix this by enabling LTO for this board, so that such
changes still can be made to the common U-Boot code.
Enable building mini u-boot image with LTO, which results in about 8KB
reduction in size.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240126081139.3210211-1-venkatesh.abbarapu@amd.com
Adding a tiny bit more code for mini u-boot leads to a OCM
image overflow. Fix this by enabling LTO for this board, so that such
changes still can be made to the common U-Boot code.
Enable building mini u-boot image with LTO, which results in about 8KB
reduction in size.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20240126080900.3209323-1-venkatesh.abbarapu@amd.com
add support for Serial Downloader Boot via UUU as well as flashing emmc
via UUU on USB0 Port of phyBOARD Pollux.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Commit 68dcbdd594d4 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" and rebooting the board causes U-Boot to hang because
of this overlap.
Fix this problem by selecting CONFIG_LTO so that the U-Boot proper
size can be reduced.
Also, to prevent this same problem to happen in the future, use
CONFIG_BOARD_SIZE_LIMIT, which can detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT is calculated as follows:
CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot-img.dtb offset
CONFIG_BOARD_SIZE_LIMIT = 0xc000 - 69 * 1024
CONFIG_BOARD_SIZE_LIMIT = 715766
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Linux 6.6.y with KASLR enabled would print the following message on boot:
"
KASLR disabled due to lack of seed
"
Enable the 'kaslrseed' command so a random number seed can be pulled
from CAAM and inserted into the /chosen node 'kaslr-seed' property of
Linux kernel DT before boot, thus letting KASLR work properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Add smbios information for Pine64 RockPro64 board and enable in
config
Signed-off-by: Shantur Rathore <i@shantur.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit enables support for DM_SERIAL in the vexpress_ca9x4 boards.
When running the board with the DM_SERIAL driver, the board ran out of
memory in SPL when initialising the DM serial driver.
Thus this required an increase in the pre-allocated SRAM memory. I did
increase it to 0x800, and it now works graciously.
It could probably be set lower, but I do not see any reason not to use the
available SRAM at this point.
Also adds stdout-path to the 'chosen' node in the device tree.
Signed-off-by: Ole P. Orhagen <ole.orhagen@northern.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Enrico Leto <enrico.leto@siemens.com> says:
The common folder was initialially created for the common parts of
the products based on draco-am355x board family. We have the
product lines 'pxm2', 'rut' and the base line unfortunately named
'draco'! Adding the new capricorn-imx8 board family, the files
were enhanced without cleanup.
Simplify first EEPROM probe and access that implements both i2c
with & without driver model. Use abstraction functions for this.
Move all am355x specifics to a new file 'board_am335x'.
Clean-up includes, config checks, maintainer.
Add support for driver model where EEPROM data are read in draco board.
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
