The correct spelling is R-Car, including the dash, update the usage.
Comment change only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The U-Boot is currently not capable of handling ethernet-phy-ieee802.3-c45
PHYs correctly, and also does not handle MDIO bus wide reset-gpios property.
Until proper C45 PHY support lands in U-Boot, disable AVB1/AVB2 interfaces.
This only disables the two MACs with 88Q2110/88Q2112 100/1000BASE-T1 PHYs
on ethenet sub-board, the main board AVB0 ethernet is unaffected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
It doesn't make sense for these files to have the x bit set. It was,
probably accidentally, added in:
Fixes: 2c494e62c31a (arm: dts: Stratix10: Add QSPI node)
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Enable PCIe/NVMe support on Data Modul i.MX8M Mini eDM SBC. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
The YModem support in SPL was never really used on this device,
the SDP support is much more convenient on i.MX8M Mini based
hardware. Replace the YModem support with SDP support.
The SDP can be utilized by forcing the board into SDP boot mode
by grounding test point right next to silkscreen label U30, and
then by using mfgtools 'uuu -brun spl flash.bin' once the device
enumerates on host system USB bus. The SDP capable USB port is
available on the USB micro-B port on the base board.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DRAM configuration GPIO straps must be accessible in SPL and before
relocation because the GPIOs are sampled both in U-Boot SPL as well as early
on in U-Boot proper. The already present bootph-pre-ram DT property made the
GPIO controllers available in SPL, but not early on in U-Boot proper, which
made gpio_request_list_by_name_nodev() in board dmo_get_memcfg() fail. Add
missing bootph-some-ram DT property to all GPIO controllers which are
referenced in dmo,ram-coding-gpios DT property to make those GPIO
controllers available early in U-Boot proper as well.
Fixes: 8c103c33fb14 ("dm: dts: Convert driver model tags to use new schema")
Signed-off-by: Marek Vasut <marex@denx.de>
Make use of OF_UPSTREAM which uses Linux dts.
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since 50cdd3f74af3 ("clk: imx: clk-imx8mn Fix nand and spi clock parent"),
drivers/clk/imx/clk-imx8mn.c clk_get_by_name(dev, "osc_24m", &osc_24m_clk)
fails with error -22 EINVAL in SPL. This is because clk_get_by_name() in the
end calls fdtdec_parse_phandle_with_args(), which iterates over all phandles
in clock-controller@30380000 { clocks = <&osc_32k>, <&osc_24m>, ... } node
'clocks' property in an attempt to find the "osc_24m" clock, but fails to
resolve the &osc_32k phandle and returns with -EINVAL.
Include the osc_32k clock in SPL DTs as a low risk fix for v2025.01 release.
This way, fdtdec_parse_phandle_with_args() can resolve both the osc_32k and
following osc_24m phandle and successfully look up the osc_24m clock.
Fixes: 50cdd3f74af3 ("clk: imx: clk-imx8mn Fix nand and spi clock parent")
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mn-beacon
Wadim Egorov <w.egorov@phytec.de> says:
Our SoMs are available in multiple configurations, managed via device
tree overlays. To determine the specific variant in use, we read the
EEPROM and apply the appropriate overlays during boot to the device tree
used by the OS.
Apply overlays for phyCORE-AM62x and phyCORE-AM64x SoMs.
Future K3 SoMs will be able to reuse this logic and overlays.
Link: https://lore.kernel.org/r/20241030164815.1763506-1-w.egorov@phytec.de
Include SoM dt-overlays that handle variants of our SoMs into
u-boot's FIT image.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Include SoM dt-overlays that handle variants of our SoMs into
u-boot's FIT image.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Sort the DTSI alphabetically. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ethernet0_rmii_pins_a pinmux change has no effect on any
DHSOM based hardware. The mco2_pins_a and mco2_sleep_pins_a
are both part of stm32mp15-pinctrl.dtsi . Drop both pinmux
changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove unused local DT copies after the OF_UPSTREAM conversion.
Fixes: cccb29fc1270 ("ARM: dts: stm32: Switch to using upstream DT on DH STM32 DHSOM")
Reported-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In previous version of pwm driver, the polarity of pwm were implemented
in reverse. In recent release, that issue in the driver is fixed,
therefore, correctly set the polarity in the device tree.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3e8e38b77101335f86bca0f05b3988877bb12993.1729766551.git.michal.simek@amd.com
Use RTC available in HW on Kria SOM without using emulation that's why
configure it properly and disable emulated one.
Power on reset value of RTC Calibration register without battery backup is
not matching with crystal frequency which leads to RTC time drift. That's
why write CALIB_WRITE register with crystal frequency (0x7FFF). There is
also an option to write zero so that Linux will set default value (0x7FFF)
in driver probe but calibration 0 is not permited by DT schema.
Co-developed-by: Srinivas Goud <srinivas.goud@amd.com>
Signed-off-by: Srinivas Goud <srinivas.goud@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9b684faeec85381b9b8fe796aaebc2ee79f17b8e.1729663761.git.michal.simek@amd.com
The FriendlyElec NanoPi R2S Plus is a single-board computer based on
Rockchip RK3328 SoC. It features e.g. 1 GB DDR4 RAM, 32 GB eMMC,
SD-card, 2x GbE LAN, optional M.2 SDIO Wi-Fi and 2x USB 2.0 host.
Features tested on a NanoPi R2S Plus 2309:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Cool Pi GenBook, it works as a carrier board
connect with CM5 SOM.
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
Tested by Armbian boot on USB disk.
Change-Id: I4d9b8572dc7c400077dde666633f3fea1b47dd03
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For upstream Linux kernel we use below DTBs for HiHope boards:
- r8a774a1-hihope-rzg2m-ex.dtb
- r8a774e1-hihope-rzg2h-ex.dtb
- r8a774b1-hihope-rzg2n-ex.dtb
Update the CONFIG_OF_LIST to match the above. Now that we have switched
upstream DTS, drop deleting the nodes and also rename the
r8a774*-u-boot.dtsi files to r8a774*-ex-u-boot.dtsi to match the OF_LIST
files so that the `bootph-all` property gets applied to required nodes
in upstream DTS.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
We are now using the dts/upstream subtree for the RZ/G2L SoC family so
we can drop unused devicetree files from arch/arm/dts.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable OF_UPSTREAM to use upstream DT and add nxp/imx/ prefix to the
DEFAULT_DEVICE_TREE. And thereby directly build DTB from dts/upstream/src/
including *-u-boot.dtsi files from arch/$(ARCH)/dts/ directory.
Signed-off-by: Marek Vasut <marex@denx.de>
Commit 136b7b6d2e98 ("Subtree merge tag 'v6.11-dts' of dts repo [1] into
dts/upstream") updates the upstream dts for E850-96 board, bringing
upstream TRNG node. There is no need to keep TRNG node in appended dts
anymore, so remove it.
Tested on E850-96 board by running 'rng' command in U-Boot shell.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Create an SoC R5 dtsi file that could be used at board level R5 files. This
would help in keeping the SoC level changes in sync across board files.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet (through eQOS interface)
- SD-Card
- UART console
The device tree file is taken from upstream Linux Kernel
through OF_UPSTREAM
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jan Kiszka <jan.kiszka@siemens.com> says:
This adds support for the new IOT2050 SM variant, introduces a sysinfo
driver which also permits SMBIOS support and switches the board to
OF_UPSTREAM. There are some further fixes for the boards included as well.
Not yet included is configuration support for DMA isolation via the PVU as
this depends on not yet merged DT bindings and another overlay.
[trini: This is just the first 10 patches in the series for now]
Link: https://lore.kernel.org/r/cover.1729577070.git.jan.kiszka@siemens.com
Main differences between the new variant and Advanced PG2:
1. Arduino interface is removed. Instead, an new ASIC is added for
communicating with PLC 1200 signal modules.
2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is
available.
3. DP interface is tailored down. Instead, to communicate with the
PLC 1200 signal modules, a USB 3.0 type B connector is added but the
signal is not USB.
4. DDR size is increased to 4 GB.
5. Two sensors are added, one tilt sensor and one light sensor.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: rebased over OF_UPSTREAM]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This requires some tweaking of the defconfig and
board_fit_config_name_match so that the new sources are taken into
account.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
We can simply use the default DT, Basic PG1, because no nodes that are
different between the variants play a role for SPL. Will help with the
migration to OF_UPSTREAM.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Patrick Rudolph <patrick.rudolph@9elements.com> says:
Based on the existing work done by Simon Glass this series adds
support for booting aarch64 devices using ACPI only.
As first target QEMU SBSA support is added, which relies on ACPI
only to boot an OS. As secondary target the Raspberry Pi4 was used,
which is broadly available and allows easy testing of the proposed
solution.
The series is split into ACPI cleanups and code movements, adding
Arm specific ACPI tables and finally SoC and mainboard related
changes to boot a Linux on the QEMU SBSA and RPi4. Currently only the
mandatory ACPI tables are supported, allowing to boot into Linux
without errors.
The QEMU SBSA support is feature complete and provides the same
functionality as the EDK2 implementation.
The changes were tested on real hardware as well on QEMU v9.0:
qemu-system-aarch64 -machine sbsa-ref -nographic -cpu cortex-a57 \
-pflash secure-world.rom \
-pflash unsecure-world.rom
qemu-system-aarch64 -machine raspi4b -kernel u-boot.bin -cpu cortex-a72 \
-smp 4 -m 2G -drive file=raspbian.img,format=raw,index=0 \
-dtb bcm2711-rpi-4-b.dtb -nographic
Tested against FWTS V24.03.00.
Known issues:
- The QEMU rpi4 support is currently limited as it doesn't emulate PCI,
USB or ethernet devices!
- The SMP bringup doesn't work on RPi4, but works in QEMU (Possibly
cache related).
- PCI on RPI4 isn't working on real hardware since the pcie_brcmstb
Linux kernel module doesn't support ACPI yet.
Link: https://lore.kernel.org/r/20241023132116.970117-1-patrick.rudolph@9elements.com
Add support for Arm sbsa [1] v0.3+ that is supported by QEMU [2].
Unlike other Arm based platforms the machine only provides a minimal
FDT that contains number of CPUs, ammount of memory and machine-version.
The boot firmware has to provide ACPI tables to the OS.
Due to this design a full DTB is added here as well that allows U-Boot's
driver to properly function. The DTB is appended at the end of the U-Boot
image and will be merged with the QEMU provided DTB.
In addition provide documentation how to use, enable binman to fabricate both
ROMs that are required to boot and add ACPI tables to make it full compatible
to the EDK2 reference implementation.
The board was tested using Fedora 40 Aarch64 Workstation. It's able
to boot from USB and AHCI or network.
Tested and found working:
- serial
- PCI
- xHCI
- Bochs display
- AHCI
- network using e1000e
- CPU init
- Booting Fedora 40
1: Server Base System Architecture (SBSA)
2: https://www.qemu.org/docs/master/system/arm/sbsa.html
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Update defconfig to enable features included in pending upstream DT and
implement board_fit_config_name_match() to load correct DT for LTS and
non-LTS version of the NanoPC-T6.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The SPI flash node has been added in upstream DT, drop all props beside
bootph-* props from the SPI flash related nodes from u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The SPI flash node has been added in upstream DT, drop all props beside
bootph-* props from the SPI flash related nodes in u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The SPI flash node has been added in upstream DT, drop all props beside
bootph-* props from the SPI flash related nodes in u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22989
- Remove unneeded USB board code and fix reset on mx6ul_14x14_evk.
- Update fastboot buffer size/address for verdin-imx8m{m|p}.
- Fix imxrt1050-evk boot and convert it to standard boot.
- Fix imx8qxp-mek and imx8qm-mek boot.
- Add support for the i.MX93 9X9 QSB board.
- Make livetree API to work on i.MX.
- Set sane default value for i.MX8M SPL_LOAD_FIT_ADDRESS.
- Deduplicate DH i.MX8MP/i.MX6 DHSOM defconfigs.
- Select default TEXT_BASE for i.MX6/i.MX7.
- Several updates for DH i.MX8MP DRC02.
Two of the clocks required by the usdhc1 controller are missing from the
clock controller node. A recent change enables all the clocks in the
esdhc node, which fails as they are not defined in the clock controller.
Fixes: 76332fae769 ("mmc: fsl_esdhc_imx: Enable AHB/IPG clk with clk bulk API")
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
The Hardkernel ODROID-M1S is a single-board computer based on Rockchip
RK3566 SoC. It features e.g. 4/8 GB LPDDR4 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0.
Features tested on a ODROID-M1S 8GB rev1.0 20230906:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Features tested on a ODROID-M2 16GB rev1.0 20240611:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the board detection logic (again) to make it compatible with
the upstream device-trees, and switch to OF_UPSTREAM.
Now the device boots with the device-tree for the 353P, and then
loads the correct device tree (of 10) in the later stages of SPL.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
