Introduce board/renesas/common/Makefile and remove the multiple
duplicate copies of obj := ../common/*.o from board Makefiles.
Let the build system include the common Makefile using the
HAVE_VENDOR_COMMON_LIB and build the common objects that are
shared by all the boards that way. No functional change intended.
Some of the remaining board files which include board specific
settings have been updated to use obj-y += to avoid rewriting
the board obj-y target and avoid dropping object files from the
build.
The board/renesas/common/Makefile is now also used when building
RZG2L targets which also set CONFIG_RCAR_64 symbol and 32bit R-Car
Gen2 targets, however, this common code is specific to 64bit R-Car
only. Inhibit the build of this common code for RZG2L using extra
ifndef CONFIG_RZG2L and do not include any code for R-Car Gen2 so
far.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The SPL on R-Car V3U Falcon is never built, remove the Makefile entry.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Rename directory board/renesas/rcar-common to board/renesas/common and
move files. This allows the build system to use HAVE_VENDOR_COMMON_LIB
which automatically includes board/$(VENDOR)/common/Makefile . Create
temporarily empty board/renesas/common/Makefile to be extended with
actual content later in this series. This is a preparatory patch for
board Makefile simplification. No functional change so far.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Samsung Galaxy Core Prime VE LTE is an entry-level PXA1908-based
smartphone. It has 1GB of DRAM, 8GB eMMC and USB connectivity.
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Enabling ODT is required to suppress reflection of the data signal on
DDR write operation. SolidRun Armada 388 SoM only connects M_ODT[0] even
when both chip-select are used.
Enable ODT[0] for both chip-select during write only.
Original work by Baruch Siach [1] and Chris Packham [2].
[1] aba763a611
[2] dbaf09590d
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This config is causing conflicts with how fdtfile variable is
initialized.
For K3 devices, CONFIG_DEFAULT_DEVICE_TREE= "ti/k3-<board>.dtb".
With CONFIG_TI_FDT_FOLDER_PATH also prefixing "ti", fdtfile is then
"ti/ti/k3-<board>.dtb". This variable is updated when fitImage is
booted and fails to boot due to the parsing error "ti/ti/".
Given that there are no other users of this config other than K3 for
now, it is being removed.
Since am64x, j721e and j721s2 also define a DEFAULT_FDT_FILE, update
them to conform to the DEFAULT_DEVICE_TREE standard.
Signed-off-by: Aashvij Shenai <a-shenai@ti.com>
We set the boot source as environment variable 'boot'.
Also include 'uart' and 'usbdfu' as possible boot sources.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
With commit 22ce56a3ebdb ("ram: k3-ddrss: Add k3_ddrss_ddr_bank_base_size_calc()
to solve 'calculations restricted to 32 bits' issue") we need to provide the
detected RAM size in the device tree node prio to K3 DDRSS driver probe.
This is done by calling fdt_fixup_memory_banks() in do_board_detect().
After probing, call into k3-ddrss driver to fixup device tree and resize
the available amount of DDR if ECC is enabled.
A third fixup is required from A53 SPL to take the fixup
as done from R5 SPL and apply it to DT passed to A53 U-boot,
which in turn passes this to the OS.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
In newer 1.2 PinePhone board revisions LIS3MDL magnetometer was replaced by
AF8133J. They use the same PB1 pin in different modes.
LIS3MDL uses it as an gpio input to handle interrupt.
AF8133J uses it as an gpio output as a reset signal.
It wasn't possible at runtime to enable both device tree
nodes and detect supported sensor at probe time.
AF8133J has reset pin (PB1) connected to the SoC. By default AF8133J
is in a reset state and don't respond to probe request on I2C
bus. Extra code would be needed to handle reset signal. Therefore this
code uses LIS3MDL magnetometer instead of AF8133J.
Introducing new dts 1.2b with AF8133J sensor would require probing in
SPL. That would lead to pulling in into SPL I2C controller driver,
RSB controller driver, introducing new AXP803 driver to power-up
sensors for probe. It's working, but SPL is pretty size-constrained on
A64 and doesn't have much space. Therefore fdt fixup is done in U-Boot
proper without introducing new board revision and new dts.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://lore.kernel.org/all/20240908214718.36316-1-andrej.skvortzov@gmail.com/
Link: https://lists.denx.de/pipermail/u-boot/2024-February/545700.html
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: fix formatting]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all sunxi boards programming the DCDC1 power rail on the AXP PMIC
also set the DCDC5 rail, so we could handle both with the same DCDC1
guard.
Some boards using the AXP313 will need to set DCDC1 now as well, and
since the AXP313 only has three buck converters, there will be no DCDC5,
so this trick is not going to work anymore.
Don't try to be too clever, and just protect programming the two DCDC
rails with two separate guards.
This has the interesting side effect of fixing operation on A80 boards,
using the AXP809 PMIC. Apparently programming DCDC5 right after DCDC1,
but before the other three rails caused some glitch, which made the board
hang during Linux boot, during the PSCI handler in U-Boot. Just keeping
the old setup order (DCDC1,2,3,4,5) will make those boards boot to the
Linux prompt again.
Fixes: ffb02942fab024d4a9b6a ("sunxi: board: simplify early PMIC setup conditions")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Add defconfig & devicetree for IBM SBP1 board BMC based on AST2600 SoC.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Include k3_rproc.env to access rproc boot commands and specify rproc
firmware names for adding remoteproc support in J722S SoCs.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add instructions on how to build and package OP-TEE for the
phycore-imx8mm based boards. The build instructions are identical for
phyGATE-Tauri-L and phyBOARD-Polis.
Also fix missig '-' for TF-A build instructions.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Enable dynamic settings to mmcdev and mmcroot for i.MX8MQ-EVK
Since we are here, clean up the including headers
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for K230 CanMV board with serial console and usb otg
support. It can boot via vendor's u-boot-spl and boot into Linux
via tftp through the onboard RTL8152.
Signed-off-by: Junhui Liu <junhui.liu@pigmoral.tech>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As there are few redundant functions in board/ti/*/evm.c files, pull
them to a common location of access to reuse and include the common file
to access the functions.
Call k3-ddrss driver through fixup_ddr_driver_for_ecc() to fixup the
device tree and resize the available amount of DDR, if ECC is enabled.
Otherwise, fixup the device tree using the regular
fdt_fixup_memory_banks().
Also call dram_init_banksize() after every call to
fixup_ddr_driver_for_ecc() is made so that gd->bd is populated
correctly.
Ensure that fixup_ddr_driver_for_ecc() is agnostic to the number of DDR
controllers present.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
This releases the DP configuration from reset early on during the boot process
for K26 SOM. It will also avoid the boot hang situation should any attempt be
made to configure the DP registers while it is still in reset.
Fixes the same issue as described by the commit 8b81010a2fe3 ("video:
zynqmp: Add support for reset").
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20241218130129.687650-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
USB hub initialization is done by driver introduced by commit 09f557e106ef
("usb: onboard-hub: Add i2c initialization for usb5744 hub") that's why
there is no need to do initialization via variables.
Reported-by: Love Kumar <love.kumar@amd.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/96e9c80aeeed4e9664858bf236476997d17a9914.1734522042.git.michal.simek@amd.com
The main reason for this change is that upstream QEMU has no multiboot
register implemented that's why access to it fails which ends up in CI
failure for our target.
That's why in JTAG bootmode returns 0 which is correct behaviour because
multiboot register is not used in this mode and value should be ignored and
as a side effect it is also fixing CI/Qemu issue.
Also move versal_get_bootmode() to avoid function declaration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/484b9cafc45e72308a1a29a3ab772020f96784cc.1736155238.git.michal.simek@amd.com
Use generic is_cortex_a() functions instead of open-coded midr_el1 read.
No functional change.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The commit 7cec3e701940 ("rockchip: rk3588-nanopc-t6: Add support for
NanoPC-T6 LTS") added support for the LTS variant of NanoPC T6. However,
a board specific -u-boot.dtsi file was never added.
Due to the missing -u-boot.dtsi file the LTS fdt included in the FIT is
never tagged with bootph props.
When ENV_IS_IN_SPI_FLASH is enabled, not enabled in defconfig, the env
can successfully load from SPI flash on the non-LTS variant, something
that does not work on the LTS variant due to missing bootph-some-ram
props in the LTS fdt.
Fix this by adding a LTS -u-boot.dtsi file that just include the non-LTS
-u-boot.dtsi file.
Reported-by: Ricardo Pardini <ricardo@pardini.net>
Fixes: 7cec3e701940 ("rockchip: rk3588-nanopc-t6: Add support for NanoPC-T6 LTS")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa ROCK 5C[1] is a Rockchip RK3588S2 based single board computer.
[1] https://radxa.com/products/rock5/5c
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPi R3S(as "R3S") is an open source platform with dual-Gbps
Ethernet ports designed and developed by FriendlyElec for IoT
applications.
Specification:
- Rockchip RK3566
- 2GB LPDDR4X RAM
- optional 32GB eMMC module
- SD card slot
- 2x 1000 Base-T
- 3x LEDs (POWER, LAN, WAN)
- 2x Buttons (Reset, MaskROM)
- 1x USB 3.0 Port
- Type-C 5V 2A Power
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
