Rename spl_soc_init() to spl_dram_init() because the generic function
name does not reflect what the function actually does. Also
spl_dram_init() is commonly used for dram initialization and should be
called from board_init_f().
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add configs related to spi nor flash for Sophgo Milk-V Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add spi nor flash controller node for cv18xx SoCs
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add spi nor flash controller driver for cv1800b SoC
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add configs related to ethernet and ethernet boot command for Sophgo Milk-V
Duo board
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Initialize register in cv1800b ethernet phy to make it compatible with
generic phy driver
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Let the sbi command detect the coreboot and oreboot SBI Implementation IDs
defined in SBI specification v2.0.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
OpenSBI has implemented the Supervisor Software Events Extension.
Allow detecting it in the sbi command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add sysreset configs as well as poweroff and reset commands for Sophgo
Milk-V Duo board.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bind cv1800b sysreset driver for Sophgo Milk-V Duo board in board_init
function.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Currently, only the receive delay is configured while the transmit delay
is not set, which may result in errors when writing to the file. This issue
can be resolved by setting PHY_TX_SRC_INVERT to SDHCI_PHY_TX_RX_DLY.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The instruction and data cache line sizes of Andes core
are 64-byte. Select SYS_CACHE_SHIFT_6 for RISCV_NDS so
the SYS_CACHELINE_SIZE is enabled with a default value.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We should not pass GUIDs by value as this requires copying.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use Sphinx style for return value.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Previous patches added QueryVariableInfo at runtime tests and
split a common function that can be used at boottime. Weire it
up and run a similar set of tets. While at it move a test which is
checiking for 0 available storage in the common code
Add tests for
- Test QueryVariableInfo returns EFI_SUCCESS
- Test null pointers for the function arguments
- Test invalid combination of attributes
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Since we support QueryVariableInfo at runtime now add the relevant
tests. Since we want those to be reusable at bootime, add them
in a separate file
Add tests for
- Test QueryVariableInfo returns EFI_SUCCESS
- Test null pointers for the function arguments
- Test invalid combination of attributes
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Since commit c28d32f946f0 ("efi_loader: conditionally enable SetvariableRT")
we are enabling the last bits of missing runtime services.
Add support for QueryVariableInfo which we already support at boottime
and we just need to mark some fucntions available at runtime and move
some checks around.
It's worth noting that pointer checks for maxmimum and remaining
variable storage aren't when we store variables on the RPMB, since the
Secure World backend is already performing them.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The check of the return code is already done a few lines above.
Although it doesn't cause any functional issues, remove the superfluous
checks
Addresses-Coverity-ID: 492766 Control flow issues (DEADCODE)
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If 'env print -e' is invoked without variable name, all UEFI variables are
listed.
Describe that 'env print -e' requires CONFIG_HEXDUMP=y to print content of
UEFI variables.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If the UEFI boot manager fails there is no point in installing the
device-tree as a configuration table.
Unload image if device-tree cannot be installed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The image is not unloaded if a security violation occurs.
If efi_set_load_options() fails, we do not free the memory allocated for
the optional data. We do not unload the image.
* Unload the image if a security violation occurs.
* Free load_options if efi_set_load_options() fails.
* Unload the image if efi_set_load_options() fails.
Fixes: 53f6a5aa8626 ("efi_loader: Replace config option for initrd loading")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If efi_bootmgr_load() fails, there is no point in trying to start an image
that has not been loaded.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI_CALL() invokes __efi_entry_check() which executes set_gd(efi_gd).
There is no need to execute set_gd(efi_gd) again via efi_restore_gd().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Daniel Schultz <d.schultz@phytec.de> says:
This patch series extends PHYTEC's SOM detection by minor
fixes, a generic helper function and a new valid flag.
Moreover, it adds a module to provide access to the SOM
detection for our TI AM6 products.
Add all functions to read each SOM option from the EEPROM
image and detect whether it's the correct product for this
image.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The ptr variable is currently defined as int and sizeof
returns the size of the eeprom data struct as Byte (32 in total).
In case the eeprom is empty, the check, if the eeprom is empty,
will most likely stop after 8 iterations because it will continue
with the stack which should contain some data. Therefore, the
init function will detect an empty EEPROM as API0 and return with
the valid flag set to True.
Fixes: dc22188cdc8 ("board: phytec: Add common PHYTEC SoM detection")
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
For all of the functions that access the eeprom_data, make sure these
data are valid. Use the valid member of the phytec_eeprom_data struct.
This fixes a bug where only the API revision check guarded against
accessing rubbish. But if API revision was e.g. 6, eeprom setup failed
before, but phytec_get_imx8m_eth would still happily access the data.
Fixes: dc22188cdc8 ("board: phytec: Add common PHYTEC SoM detection")
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Add a new nember to the eeprom_data that indicates whether the
associated data is valid or not. Make use of this new member in the
phytec_eeprom_data_init function by setting the valid value
appropriately.
Move the eeprom data to a new struct payload that holds
the payload of the eeprom.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Add a generic function to apply overlays in our board code to not
implement the same logic in different PHYTEC products.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
The phycore-rk3288 can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for rockchip vendor prefix accordingly.
Move device tree nodes required for u-boot to rk3288-phycore-rdk-u-boot.dtsi
such as chosen, i2c_eeprom_id and it's alias.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am64x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
While at it, drop the redundant definitions of AM642_PHYBOARD_ELECTRA_DTB
& SPL_AM642_PHYBOARD_ELECTRA_DTB from the binman dtsi file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am62x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Judith Mendez <jm@ti.com> says:
The following patch series includes a MMC tuning algorithm
fix according to the following published paper [0].
This seris also includes fixes for OTAP/ITAP delay values
in j721e_4bit_sdhci_set_ios_post and for HS400 mode.
For DDR52 mode, also set ENDLL=1 and call am654_sdhci_setup_dll()
instead of am654_sdhci_setup_delay_chain() according to
device datasheet[1].
[0] https://www.ti.com/lit/an/spract9/spract9.pdf
[1] https://www.ti.com/lit/ds/symlink/am62p.pdf
At HS400 mode the ITAPDLY value is that from High Speed mode
which is incorrect and may cause boot failures.
The ITAPDLY for HS400 speed mode should be the same as ITAPDLY
as HS200 timing after tuning is executed. Add the functionality
to save ITAPDLY from HS200 tuning and save as HS400 ITAPDLY.
Fixes: c964447ea3d6 ("mmc: am654_sdhci: Add support for input tap delay")
Signed-off-by: Judith Mendez <jm@ti.com>
According to the device datasheet [0], ENDLL=1 for
DDR52 mode, so call am654_sdhci_setup_dll() and write
itapdly after since we do not carry out tuning.
[0] https://www.ti.com/lit/ds/symlink/am62p.pdf
Fixes: c964447ea3d6 ("mmc: am654_sdhci: Add support for input tap delay")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Set itap_del_ena if ITAPDLY is found in DT or if the tuning
algorithm was executed and found the optimal ITAPDLY. Add the
functionality to save ITAPDLYENA that can be referenced later
by storing the bit in array itap_del_ena[].
Signed-off-by: Judith Mendez <jm@ti.com>
U-Boot is failing to boot class U1 UHS SD cards due to incorrect
OTAP and ITAP delay select values. Update OTAP and ITAP delay select
values from DT.
Fixes: c7d106b4eb3 ("mmc: am654_sdhci: Update output tap delay writes")
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Currently the sdhci_am654 driver only supports one tuning
algorithm which should be used only when DLL is enabled. The
ITAPDLY is selected from the largest passing window and the
buffer is viewed as a circular buffer.
The new tuning algorithm should be used when the delay chain
is enabled; the ITAPDLY is selected from the largest passing
window and the buffer is not viewed as a circular buffer.
This implementation is based off of the following paper: [1].
Also add support for multiple failing windows.
[1] https://www.ti.com/lit/an/spract9/spract9.pdf
Fixes: a759abf569d4 ("mmc: am654_sdhci: Add support for software tuning")
Signed-off-by: Judith Mendez <jm@ti.com>
Caleb Connolly <caleb.connolly@linaro.org> says:
This is a subset of [1]. With more platform maintainers switching to
OF_UPSTREAM I didn't want to get in the way (it has also proven more
difficult than I hoped to remove only the fully compatible header
files).
This series removes only the dt-bindings headers which contain generic
data like GPIO flags, input event codes, etc.
It then implements support for building all DTBs for a vendor with
OF_UPSTREAM_BUILD_VENDOR. This removes the need to maintain a set list
of DTBs that can be built by U-Boot and opens up the possibility of new
boards becoming supported "by default" just by landing their DT
upstream.
[1]: https://lore.kernel.org/u-boot/20240321-b4-upstream-dt-headers-v2-0-1eac0df875fe@linaro.org
This adjusts OF_UPSTREAM to behave more like the kernel by allowing for
all the devicetree files for a given vendor to be compiled. This is
useful for Qualcomm in particular as most boards are supported by a
single U-Boot build just provided with a different DT.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on Amlogic boards builds
Drop all the subsystem headers that are compatible with the headers in
dts/upstream.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
MD Danish Anwar <danishanwar@ti.com> says:
The series introduces device tree and config changes and AM65x
to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY
for AM65x in order to load overlay over spl.
The ICSSG2 node is added in device tree overlay so that it remains in
sync with linux kernel.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
The users need to set env variables fw_storage_interface, fw_dev_part,
fw_ubi_mtdpart, fw_ubi_volume to indicate which storage medium and
partition they want to use to load firmware files from. By default the env
fw_storage_interface=mmc and fw_dev_part=1:2 but users can modify these
envs as per their requirements.
When ICSSG driver is enabled (CONFIG_TI_ICSSG_PRUETH=y) set
storage_interface and fw_dev_part env variables.
These variables need be set appropriately in order to load differnet
ICSSG firmwares needed for ICSSG driver. By default the storage
interface is mmc and the partition is 1:2. User can modify this based on
their needs.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
When CONFIG_TI_ICSSG_PRUETH is enabled, add config name check for the
icssg2 overlay in board_fit_config_match() API.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
