commit f0215440069c4fb12958d2d321e05faa2708a11d Linux upstream.
The patch adds support for touchscreen on the stm32f746-disco board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 7a5f349e592c254f3c1ac34665b6c3905576efc2 Linux upstream.
The patch replaces the number 12 with the appropriate numerical constant
already defined in the file stm32f7-rcc.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 0920ccdf41e3078a4dd2567eb905ea154bc826e6 Linux upstream.
Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The
chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral
configuration and CAN3 in single peripheral configuration:
- Dual CAN peripheral configuration:
* CAN1: Primary bxCAN for managing the communication between a secondary
bxCAN and the 512-byte SRAM memory.
* CAN2: Secondary bxCAN with no direct access to the SRAM memory.
This means that the two bxCAN cells share the 512-byte SRAM memory and
CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
* CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
512-byte SRAM memory.
-------------------------------------------------------------------------
| features | CAN1 | CAN2 | CAN 3 |
-------------------------------------------------------------------------
| SRAM | 512-byte shared between CAN1 & CAN2 | 512-byte |
-------------------------------------------------------------------------
| Filters | 26 filters shared between CAN1 & CAN2 | 14 filters |
-------------------------------------------------------------------------
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 011644249686f2675e142519cd59e81e04cfc231 Linux upstream.
Add pin configurations for using CAN controller on stm32f7.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize RZ R8A774E1 RZ/G2H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774C0 RZ/G2E DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774B1 RZ/G2N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774A1 RZ/G2M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Synchronize RZ R7S72100 RZ/A1 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779F0 S4 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779A0 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77995 D3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77990 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77980 V3H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77970 V3M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77965 M3-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77951 H3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7794 E2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7790 H2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
A '.update' extension does not get preserved by buildman, so change it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Walle <michael@walle.cc>
Trying to boot a fitImage after a successful hab_auth_img operation
causes the following error:
## Loading kernel from FIT Image at 88000000 ...
Using 'conf-imx7d-smegw01.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x8800010c
Data Size: 9901752 Bytes = 9.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80800000
Entry Point: 0x80800000
Hash algo: sha256
Hash value: 28f8779bbf010780f16dd3d84ecb9b604c44c5c2cf7acd098c264a2d3f68e969
Verifying Hash Integrity ... sha256Error in SEC deq
CAAM was not setup properly or it is faulty error!
The reason for this error is that the BootROM uses the CAAM Job Ring 0,
so disable its node in U-Boot to avoid the resource conflict.
imx8m dtsi files also have the Job Ring 0 disable since the following
kernel commit:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch?h=v6.5&id=dc9c1ceb555ff661e6fc1081434600771f29657c
For a temporary solution, disable the Job Ring 0 in imx7s-u-boot.dtsi.
Reported-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Correct the i2c address for si570 oscillator that generates the si570_user1
clock. i2c address was changed by commit b6a8c603d680 ("arm64: zynqmp: Fix
i2c addresses for vck190 SC") because address in node name wasn't aligned
with reg property. But actual 0x5f address is correct which is quite rare
because all other si570s are at 0x5d.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6f31881b0e2dd657f0d4ff0869c009c2e1224f22.1694441445.git.michal.simek@amd.com
Added no-wp DT property in OSPI flash node for all board dts & dtsi files
on which the WP# signal of the OSPI flash device is not connected. If this
property is set, then the software will avoid setting the status register
write disable (SRWD) bit in status register during status register
write operation.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e88dd7b9306bdf0738b2248bf9017e1997d25dc.1694441445.git.michal.simek@amd.com
xlnx,mio_bank was used in past but it was renamed to xlnx,mio-bank because
'_' in property shoudln't be used. There is no impact on the platform
because if the properly is not defined bank 0 is default. Bank 0 and 1 have
the same configuration that's why there shouldn't be any issue.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ace68d4b7701d1606a85cb18242409fce941b363.1694441445.git.michal.simek@amd.com
Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.
Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.
In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
gpio toggle gpio@ff0a000038
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7ecd98b2a302c5c6628e0234482f23c38e721fd6.1693492064.git.michal.simek@amd.com
Revision 2 is SW compatible with revision 1 but it is necessary to reflect
it in model and compatible properties which are parsed by user space.
Rev 2 has improved a power on boot reset and MIO34 shutdown glich
improvement done via an additional filter in the GreenPak chip.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6b9e68ebfb436da391daeb147f2a9985ac984c0c.1692951005.git.michal.simek@amd.com
All si570 mgt chips have factory default 156.25MHz but DT changed it to
148.5MHz. After tracking it is pretty much c&p fault taken from Zynq
zc702/zc706 boards where 148.5MHz was setup as default because it was
requirement for AD7511 chip available on these boards.
ZynqMP board don't contain this chip that's why factory default frequency
can be used.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c052ddf39e392e97f87f1c57ea06f3508733c672.1692947486.git.michal.simek@amd.com
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
NOTE: sync with v6.6-rc1 will bring in this change naturally.
Signed-off-by: Nishanth Menon <nm@ti.com>
Introduce the new serdes header from kernel v6.6-rc1
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Signed-off-by: Nishanth Menon <nm@ti.com>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To have the WDIOF_CARDRESET support for the TI AM65x platform watchdog,
this patch reserves some memories, which indicate if the current boot due
to a watchdog reset.
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Update the DDR settings to those generated using 0.10 version of Jacinto
7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.
This board family can be identified by the 24c32 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 45 41 47 4c 45 |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d 00 00 30 32 30 30 37 38 |PLAY-A0-..020078|]
https://beagleplay.org/https://git.beagleboard.org/beagleplay/beagleplay
baseline of base device tree is v6.5-rc1.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
Add a newline at the end of the dts, without which the build fails
when including a dtsi file.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
