A valid memory location to stash bootstage information at will be
architecture dependent. Move the existing defaults to the main Kconfig
file for this option and set 0x0 as the default only for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
After adding the U_BOOT_LONGHELP macro some new commands came in still
that were not making use if it. Switch these cases over and in a few
places add missing newlines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch makes STM32 PWR regulators available on stm32mp13xx.
This requires TFA to clear RCC_SECCFGR, is disabled by default
on stm32mp13xx and can only be enabled on board config level.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since commit 7b78d6438a2b3 ("efi_loader: Reserve unaccessible memory")
memory region above ram_top is tagged in EFI memory map as
EFI_BOOT_SERVICES_DATA.
In case of STM32MP1/STM32MP13 platforms, above ram_top, there is one
reserved-memory region tagged "no-map" dedicated to OP-TEE :
_ addr=de000000 size=2000000 for stm32mp157x-dkx and stm32mp135f-dk
_ addr=fe000000 size=2000000 for stm32mp157c-ev1
Before booting kernel, EFI memory map is first built, the OPTEE region is
tagged as EFI_BOOT_SERVICES_DATA and when reserving LMB, the tag LMB_NONE
is used.
Then after, the LMB are completed by boot_fdt_add_mem_rsv_regions()
which try to add again the same OPTEE region (addr=de000000 size=2000000
in case of stm32mp157x-dkx / stm32mp135f-dk or addr=fe000000 size=2000000
in case for stm2mp157c-ev1)
but now with LMB_NOMAP tag which produces the following error message :
_ for stm32mp157x-dkx / stm32mp135f-dk :
"ERROR: reserving fdt memory region failed (addr=de000000 size=2000000 flags=4)"
_ for stm32mp157c-ev1 :
"ERROR: reserving fdt memory region failed (addr=fe000000 size=2000000 flags=4)"
To avoid this, OPTEE area shouldn't be used by EFI, so we need to mark
it as reserved.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Make sure the OS would not get any spurious IWDG pretimeout IRQ
right after the system wakes up. This may happen in case the SoC
got woken up by another source than the IWDG pretimeout and the
pretimeout IRQ arrived immediately afterward, but too late to be
handled by the suspend main loop. In case either of the IWDG is
enabled, ping it first and then return to the OS.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
In case node "/reserved-memory/optee" is not found, return -ENOENT
instead of 0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from all mach-stm32 and mach-stm32mp files and when
needed add missing include files directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch avoids compilation issue when CONFIG_USB_GADGET is deactivated
in defconfig, with undefined reference to run_usb_dnl_gadget and to
g_dnl_set_product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
"#if" was used instead of "#ifdef"
Fixes: 01a701994b05 ("stm32mp2: initial support")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
We cannot use stm32key commands without CONFIG_CMDLINE so add the
required condition.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG options must not use lower-case letter. Convert this and related
ones to upper case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Activate the command stboard for stm32mp25 STMicroelectronics boards,
add the default used OTP identifier and the associated board identifier:
- stm32mp25xx-ev1 = MB1936
- stm32mp25xx-dk = MB1605
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change OTP number to 364 for STM32MP25 as it is done in bsec driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a function setup_mac_address() to update the MAC address from the
default location in OTP for stm32mp2 platform.
The max number of OTP for MAC address is increased to 8 for STM32MP25,
defined with get_eth_nb() and checked in setup_mac_address.
The MAC address FF:FF:FF:FF:FF:FF, the broadcast ethaddr, is a invalid
value used for unused MAC address slot in OTP, for example for board
with STM32MP25x part number allows up to 5 ethernet ports but it is not
supported by the hardware, without switch; the associated variable
"enetaddr%d" is not created.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support of serial number for stm32mp25, gets from OTP with BSEC driver.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Add a new file soc.c for common functions between stm32mp1 and stm32mp2
family and move print_cpuinfo() in this new file.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Add support of BSEC for STM32MP25x family to access OTP.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add driver data in BSEC driver to test presence of OP-TEE TA,
mandatory for STM32MP13 family and prepare the support of new device
with more OTP than 95.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add chip revision B support for STM32MP25, for displaying it in trace.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the new bootm/z_run() functions to avoid having to create an
argument list for the stm32prog code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Rather than assigning to the bootm_argv[] array multiple times, use
local variables for the two things that can change and assign them at
the end.
This makes it easier to drop the array eventually.
Tidu up an overly short line while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When building with AARCH64 defconfig, we got warnings, fix them.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Limit DDR usage under 4GB boundary on STM32MP regardless of
memory size declared in device tree.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When building with AARCH64 defconfig, we got warnings for debug
message
- format '%x' expects argument of type 'unsigned int',
but argument 3 has type 'size_t' {aka 'long unsigned int'}).
- format '%lx' expects argument of type 'long unsigned int',
but argument 2 has type 'phys_addr_t' {aka 'long long unsigned
int'}
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case there is no RAM driver retrieve RAM size from DT as fallback.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Obtain from TAMP backup register information about image authorization
status and partition id used for booting. Store this info in
environmental variables ("boot_auth" and "boot_part" correspondingly).
Image authorization supported values:
0x0 - No authentication done
0x1 - Authentication done and failed
0x2 - Authentication done and succeeded
These values are stored to TAMP backup register by Trusted Firmware-A [1].
Testing:
STM32MP> print boot_part
boot_part=1
STM32MP> print boot_auth
boot_auth=2
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?h=refs/heads/integration&id=ab2b325c1ab895e626d4e11a9f26b9e7c968f8d8
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
While 23e20b2fa6 ("arm: stm32mp: Fix compilation issue when
SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled") tried fixing
this issue, fix it really by adding #if checks for SYS_ICACHE_OFF
and SYS_DCACHE_OFF.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PWR_MPUCR CSTBYDIS bit is set, therefore the CA cores can never
enter CStandby state and would always end up in CStop state. Clear
the PDDS bit, which indicates the CA cores can enter CStandby state
as it makes little sense to keep it set with CSTBYDIS also set.
This does however fix a problem too. When both PWR_MPUCR and PWR_MCUCR
PDDS bits are set, then the chip enters CStandby state even though the
PWR_MCUCR CSTBYDIS is set. Clearing the PWR_MPUCR PDDS prevents that
from happening.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Now all linker symbols are declared as type char[]. Though we can
reference the address via both the array name 'var' and its address
'&var'. It's better to unify them to avoid confusing developers.
This patch converts all '&var' linker symbol refrences to the most
commonly used format 'var'.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Change the default base for offset parsing with simple_strtoull(),
so offset in flashlayout is coded in base 10 by default, even if string
start with '0'. The Octal encoding is not supported. The base 16
is still supported when the '0x' header is detected.
This patch solves an unexpected parsing result when the address,
provided by decimal value is starting by 0, for example 0x4400 = 00017408
is a invalid with current code.
...
P 0x04 fsbl1 Binary mmc0 00017408 tf-a.stm32
....
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Avoid to ignore the OTP read/write error and transmits the error
to STM32CubeProgrammer.
Today the error is only displayed in log error:
so the user on HOST thinks the OTP operation is performed.
Reported-by: Mickael GARDET <m.gardet@overkiz.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fixes: 75ea9e75931c ("stm32mp: stm32prog: add TEE support in stm32prog command")
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a protection in misc bsec ops for request with null size.
For example OP-TEE error occurs when get_eth_nb() return 0 in
setup_mac_address() for unknown part number because U-Boot read 0 OTPs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of STM32MP15x Rev.Y for the Silicon revision REV_ID = 0x2003.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The get_stm32mp_rom_api_table() function is defined in sys_params.h ,
add the missing header to avoid compiler warning.
Fixes: dbeaca79b79 ("ARM: stm32: Factor out save_boot_params")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
